Flywoo Goku Versatile F405 5IN1 AIO User manual

Part1- Overview
Specs Overview
01
02
02
03
04
05
06
07
09
10
11
Wiring Diagram
Receiver Wiring Configuration Diagram
Dimensions
Package
Chip Layout
Pad Layout
Part2- Layout
Part3- Diagram
Part4- Receiver Frequency Calibration Steps
Part5- Adjustment of VTX Power and Channels
Part6- Definition of VTX LEDs
Part7- Troubleshooting FAQ
Versatile F405
5IN1 AIO
1-2S 12A 400mw
Bulit-in ELRS 2.4G
Uuser Manual V1

01
Specs Overview
Product Name Versatile F405 5IN1 AIO
1-2S 12A 400mw Bulit-in ELRS 2.4G
MCU STM32F405 BGA
ICM42688
SPL06
8M
Supported
Supported
Supported
1,2,3,4,6
ExpressLRS 2.4G
25/50/100/200/400mw
IRC Tramp
12A*4
1S-2S （3V-8.7V）
FLYWOO F405S_AIO
Flywoo EL24E 2400 RX 3.0.0
Z_H_30_REV16.7(BLHELI_S)
30.3*30.3mm
Oneshot125,Oneshot42,Multishot,
Dshot150,Dshot300,Dshot600.
GYRO
Barometer
Black Box
LED
OSD
Buzzer
UART
Built-in Receiver
Built-in VTX
VTX Protocol
ESC Protocol
Input Voltage
BF Firmware Target
ELRS Firmware
ESC Firmware
Size
25.5*25.5-3mm
4.6g (Without Antenna) 5.7g (With Antenna)
Mounting
Weight
Continuous Current

41.8mm
41.8mm
8.1mm
3.8mm
25.5mm
1
1
24
35
7
6
1x PH2.0 Connector 1x 25V 220UF Capacitor
5
21x Amass XT30 Connector 1x 5.8G Antenna 6
31x Hardware Set 1x GOKU Versatile F405
5IN1 AIO
7
41x ELRS 2.4g T Antenna
Dimensions + Package
02

OSD(AT7456E)
ELRS(SX1281)
WS2812 LED
TVS Diode
Anti-Voltage
Spike
BEC(5V/2A)
Micro usb
Current sensor
Baro(SPL06)
8M BlackBox
ESC MCU(BB21)
12A Mosfets
MCU(F405BGA)
Gyro(ICM42688)
ELRS(ESP8285)
ELRS(WIFI ANT)
03
Chip Layout
ELRS(RX ANT)
5.8G(IPX ANT)
5.8G(PA Chip)
5.8G(RTC6705)

Pad Layout
ELRS RX ROOT
FC BOOT
+4.5V
BAT+ (3V-8.7V)
GND
RX(ELRS RX)
TX(ELRS TX)
04
Blue LED: VTX Channel
Yellow LED: VTX Band
Red LED: VTX Power
Red LED: FC Power
Blue LED: Gyro Status
GND +3.3V BB+ BB-
Yellow LED: ELRS RX Status
GND
GND +5V +5V RX2 TX2
LED
CAM
GND +4.5V
RX3 TX3 SBUS(RX3)
GND +4.5V GND
RX4 TX4
SDA SCL
VTX Power off/on
RX6
TX6
5V
GND
D+ D-
M2
M1
M4
M3
BAT- (GND)

Caution: O3 unit can only be
used with a voltage of 2S.
G V R T S A
05
Wiring Diagram
5v
5v
GND
GND
RX
TX
Vcc
Vcc Vcc
GND GND
RX
TX
TX
RX
GND Vcc
GND
GND
GND
SBUS
SBUS
RX
RX
TX
TX
RX
TX
Wiring Diagram

S N




Receiver Wiring Configuration Diagram


TBS Nano RX
Frsky R-XSR
ELRS(ESP8285)
ELRS(RX ANT)
Built-in ELRS
ELRS(SX128X)
ELRS(WIFI ANT)
5v
GND
TX
TX
RX
GND
5V
SBUS
GND
5V
06
RX
5v
GND
TX
SBUS

TOOLS
01 FrSky GaSuite
02 FrSky SBEC
03 FrSky SxR
04 crossfire
05 ELRS
06 ......
ExpressLRS
Pkt.Rate
TLM Ratio
Power
RF Freq
[ Bind ]
200Hz(-112dbm)
1:64 (63bps)
500mW
2.4G FCC
[ Wifi Update ]
Receiver Frequency Calibration Steps
1.1
The FC quickly turns on and off the power three
times, with the yellow light flashing twice.
1.2
Open the tool menu on the remote
controller and select ExpressLRS.
1.4
The yellow light stays on,
indicating a successful BIND.
Tips:
1. Please make sure that the ELRS TX and RX are on the same firmware version, otherwise-
binding will not be possible.
2. ELRS RX yellow status LED:
- Steady LED indicates successful frequency calibration or normal communication.
- Fast flashing LED indicates that the receiver is in frequency calibration mode.
- Slow flashing LED indicates that the receiver has no transmitter signal or has not been
frequency calibrated.
- Rapid flashing LED indicates that it is in Wi-Fi flashing mode, and you can connect to Wi-Fi to
flash the firmware in this state.
1.3
Click on BIND.
07

Adjustment of VTX Power and Channels
-- MAIN --
PROFILE
FEATURES
OSD
FC&FIRMWARE
MISC
SAVE / EXIT
CONFIRM
YES
NO
-- FEATURES --
BLACKBOX
VTX
LED STRIP
POWER
FAILSAFE
BACK
-- TRAMP --
X R7 5880 25
PIT
BAND
CHAN
( FREQ )
POWER
T (C)
SET
BACK
OFF
RACE
1
5880
25
45
1.1
Turn on the transmitter, THR middle, YAW left, PITCH up, enter the OSD menu.
1.2
The PITCH moves the cursor up and down, and the ELE right to enter the next item.
Now, save and exit.
A
b
E
F
r
5865
5733
5705
5740
5658
CH1
5845
5752
5685
5760
5695
CH2
5825
5771
5665
5780
5732
CH3
5805
5790
5645
5800
5769
CH4
5785
5809
5885
5820
5806
CH5
5765
5828
5905
5840
5843
CH6
5745
5847
5925
5860
5880
CH7
5725
5866
5945
5880
5917
CH8
Frequency table:
Usage Precautions:
1. Before powering on, make sure to install the antenna for the VTX.
2. Do not keep the power on when the device is on the ground for an extended period of time to avoid
hardware damage caused by high temperatures.
3. Pay attention to the input voltage of the flight controller and ensure it is within the specified range.
4. The flight controller generates high temperature during continuous operation, so avoid touching it to
prevent burns.
The number of red light flashes represents the power level.
The number of blue light flashes represents the channel.
1.3
Definition of VTX LEDs.
FR/CH
08
Mode-2 Mode-1
Red LED:VTX power
Yellow LED:VTX band
Blue LED:VTX channel
The number of yellow light flashes represents the
frequency band.

Troubleshooting FAQ
Q : Can the built-in ELRS be turned off ?
A: Yes, when using a Black Sheep receiver, you need to change the receiver serial port in
the ground station. The built-in receiver will not interfere with the signal transmission
and reception of an external receiver.
Q: Can other versions of ELRS firmware be flashed to the built-in receiver ?
A: Yes, it is possible. This flight controller has a complete receiver serial port and Wi-Fi
flashing capability. You can use the ELRS ground station or connect to the receiver's
Wi-Fi for firmware flashing.
09
Q: Why does the flight controller get hot when plugged into the computer for tuning ?
A: The flight controller board has a built-in video transmitter and receiver. When
connected with a micro USB cable, it starts working and generates heat, which is a
normal phenomenon. If the flight controller gets too hot, it is recommended to let it
sit for a few minutes to allow for heat dissipation.
Troubleshooting FAQ: