FMC Technologies CN3 User manual

Pos: 2/ Tec hD OC /Seni ng /I ntr o's /Erst e Seite/I ntro: CM3 @ 7\mod_1422878233031_19.docx@ 126124@ @ 1
=== En de der Lis te für Te xtmar ke Intro = ==
Issue/Rev. 1.10 (01/15)
MN F08 001 EN  DOK-347E
EN - Instruction Manual
Turbin Check Meter
CN3
Sening®is a registered trademark of FMC Technologies

CN3

General MN F08 001 EN  DOK-347E  Issue/Rev. 1.10 (01/15)
2Sening®is a registered trademark of FMC Technologies
Pos: 4/ Tec hDOC /S eni ng/H ist ori e-Hinweis-Dokumente/DOK-347_CM 3 @ 7 \mod_1422878821531_19.docx@126147@ @ 1
Further documentation about this product:
Designation Order No.
None
Pos: 5/ Tec hDOC /S eni ng/H ist ori e-Hinweis-Dokumente/DOK-000_Hi nweis : D okum ent ationI nt ernet @ 5\mod_1378739240342_19.docx@ 95534@ @ 1
Documentation on the Internet:
www.fmctechnologies.com/seningttp
Pos: 6/ Tec hDOC /S eni ng/Al lg em ein/| FÜ 1---> Inhal ts verzeic hnis ( Deuts ch) @ 2\mod_1340182989966_19.docx @ 41391@ @ 1
History
Revision
Date
Originator
Status
Description
Rev. 1.01
October 2014
TR1
Created
First edition
Rev. 1.10
Januar 2015
/ HS / jp /
WIP
Div. modifications

MN F08 001 EN  DOK-347E  Issue/Rev. 1.10 (01/15) CN3  General
Sening®is a registered trademark of FMC Technologies 3
Table of Contents (English)
=== En de der Lis te für Te xtmar ke Inhal tsver zeich nis ===
Table of Contents (English) _________________________________ 3
1General ______________________________________________ 5
1.1 Orientation aids for the manual...................................................................5
1.2 Safety instructions........................................................................................6
1.3 Notes on Ex-protection ................................................................................6
1.3.1 Proper intended use............................................................................................6
1.4 General Application Information .................................................................7
1.4.1 Measurement at a Splitted Tank Compartment ...................................................7
2Device description_____________________________________ 8
2.1 Functional Principle of the CM3 ..................................................................8
2.2 Initial Operation.............................................................................................8
2.3 Measurement Operation...............................................................................8
2.3.1 Coupling/ Uncoupling..........................................................................................8
2.3.2 Controls...............................................................................................................9
2.3.2.1 Display............................................................................................................................9
2.3.2.2 Keypad ...........................................................................................................................9
2.3.3 Measurement Procedure.....................................................................................10
2.4 Storage ..........................................................................................................11
2.4.1 Storage bracket in the vehicle .............................................................................11
2.4.2 Removal from the holder CM3-AV.......................................................................11
3Maintenance__________________________________________ 12
3.1 Battery Replacement....................................................................................12
4Technical Data ________________________________________ 14
4.1 CM3................................................................................................................14
4.2 Repairs and Replacement Parts..................................................................14
5Address and contact details_____________________________ 15
Appendix A. Drawings and Approvals _______________________ 16
Index ._____________________________________________ 16

CN3

General MN F08 001 EN  DOK-347E  Issue/Rev. 1.10 (01/15)
4Sening®is a registered trademark of FMC Technologies
Drawings 17
51.250223 – Turbine Check Meter - CM3................................................................................17
51.250243 – Holder – CM3-AV................................................................................................18
Approvals19
KEMA - Certificate Of Conformity.............................................................................................19
Pos: 8/ Tec hDOC /S eni ng/Al lg em ein/| 1---> Allgemeines@ 0\mod_1307366793031_19.docx@ 5771@ 1 @ 1

MN F08 001 EN  DOK-347E  Issue/Rev. 1.10 (01/15) CN3

General
Sening®is a registered trademark of FMC Technologies 5
1 General
Pos: 9/ Tec hDOC /S eni ng/Al lg em ein/2 : O rien tier ung shi lfe n + Pi kt ogr amm e @ 0 \mod_1307366793359_19.docx@ 5784 @ 2@ 1
1.1 Orientation aids for the manual
We have provided some orientation aids so that you can easily find the necessary
information in this manual.
The information in this manual ranges from imperative safety procedures and standardized
guidelines through to concrete handling procedures and advice. To differentiate these more
easily, the information is marked with corresponding pictograms in front of the relevant text.
These are intended not just to draw particular attention to these passages, but also to make
it easier to find the information you want. Therefore the pictograms are symbolic of the
underlying textual content.
The following pictograms are used in this manual:
Danger sign
Danger of explosions caused by easily ignited gases and liquids here.
Risk of operating fault
Actions that may damage the equipment.
§ Legal notice
Actions that may have legal consequences.
Working step
Concrete action statements, e.g.: “Press the <Enter> key”.
Input necessary
e.g. via numeric or function keys.
Positive response message
e.g. “The main menu now appears”
Negative response message
e.g. “If a fault message appears now...”
Background information
Short-Tip, e.g. “See more detailed information in chapter XX”.
Option
Special case.
Function
Functional description.
NOTE:
indicates a special situation.
ATTENTION:
particular attention is to be paid.

CN3

General MN F08 001 EN  DOK-347E  Issue/Rev. 1.10 (01/15)
6Sening®is a registered trademark of FMC Technologies
Pos: 10 /T ec hDO C/ Seni ng /Sic her hei t/| 2---> > Sich erhei tshi nwei se @ 1\mod_1323246313304_19.docx@30393@ 2 @ 1
1.2 Safety instructions
Pos: 11 /T echD OC/Se ning /Sicher hei t/S1: Ta belle A CHTUN G: Sic herhei tshi nweis e @ 0\mod_1309780649733_19.docx@ 8604@ @ 1
Caution:
This information must be carefully read and observed before operating
the unit.
Pos: 12 /T echD OC /Se ni ng/ Sic her hei t/ 2: Hi n weis e z um E x-Schutz (CM3)@ 7\mod_1422891378111_19.docx@126194@ 2 @ 1
1.3 Notes on Ex-protection
The CM3 are designed for flow measurements of flammable liquids
(hazard classes AI and AIII) on tank trucks. Sparks and open flames
must be strictly avoided.
The CM3 shall not be used for fuel delivery with delivery pumps.
Certificate: xxx 04 ATEX xxxx X
Ignition protection type: II 2 EEx ia IIB T4
Pos: 13 /T echD OC /Se ni ng/ Sic her hei t/| 3--->> > Bestim mung sge mäße V erwend ung @ 1\mod_1323251107348_19.docx@ 30458@ 3 @ 1
1.3.1 Proper intended use
Pos: 14 /T echD OC /Se ni ng/ Sic her hei t/S 5: B esti m mung sg em äße Ver wend ung ( CM 3) @ 7\mod_1422951837335_19.docx@ 126220@ @ 1
The CM3 is only to be used for delivery of low-viscosity petroleum products on tank trucks.
The corresponding applicable safety regulations (e.g. Ex-protection) must be complied with.
Any form of use which exceeds the scope described above is deemed to be improper use;
the manufacturer is not liable for damages resulting from such improper use.
Proper use also includes compliance with the conditions set out by the manufacturer with
regard to operation, installation and maintenance.
The CM3 must only be operated, serviced and repaired by personnel who are familiar with
the equipment and who have been trained regarding the dangers involved.
The CM3 must not be used for the discharge of fuel using a feed pump.
The manufacturer cannot be held liable for any damages arising as a result of unauthorized
changes to the measuring systems.
The CM3 contains precision, high quality components. Therefore, mechanical influences
which do not result from operation (e.g. through being dropped) must be avoided.
§ Measurements which are subject to mandatory W&M certification shall not be carried out
with this device.

MN F08 001 EN  DOK-347E  Issue/Rev. 1.10 (01/15) CN3

General
Sening®is a registered trademark of FMC Technologies 7
Pos: 15 /T echD OC/Se ning /08-Mess a nlag en/D O K-347_CM3/2:AllgemeineAnwendungshinweise@ 7\mod_1422969221787_19.docx @ 126243@ 2 @ 1
1.4 General Application Information
The CM3 has been designed for measurement of products discharge by gravity from tank
trucks without a permanent measurement systems.
However, with measurement operation it must be taken into account that the CM3 is
operated without a gas extractor, i.e. any air in the product is also metered with it.
Pos: 16 /T echD OC/Se ning /08-Mess a nlag en/D O K-347 _CM3 /3 : M ess ung bei „ ges plit te ter“ Kam mer @ 7\ mod_1422969333795_19.docx@ 126265@ 3 @ 1
1.4.1 Measurement at a Splitted Tank Compartment
If a tank compartment volume must be splitted for multiple discharges, we recommend to
start the measurement with a full compartment. This provides the best measurement result
within the stated accuracy range.
The retained volume in the compartment can be calculated by the difference between the
loaded volume and the discharged volumen.
When measuring the entire retained volume in a compartment there is a risk of air entering
the discharge system. This air will be measured as discharged volume if flow is not
interrupted.
Pos: 17 /T echD OC/Se ning /Allg emein/| 1--->G erätebeschreibung@ 7\mod_1418651340908_19.docx@123728@ 1 @ 1

CN3

Device description MN F08 001 EN  DOK-347E  Issue/Rev. 1.10 (01/15)
8Sening®is a registered trademark of FMC Technologies
2 Device description
Pos: 18 /T echD OC/ Se ning /08-M ess anlag en/ DO K-347_CM3/2:Funktionsweisedes CM3 @ 7\mod_1422969413121_19.docx@ 126287@ 2 @ 1
2.1 Functional Principle of the CM3
The liquid flowing through the impeller-type meter sets the impeller rotating.
The rotation speed is proportional to the flow volume.
The rotating movement of the impeller blades is transferred by a magneto-inductive sensor.
These signals are evaluated within the measuring electronics and displayed.
The momentary flow rate in /min and the total dischargedvolume in litres can be displayed.
In addition a non-resettable totaliser is provided.
Pos: 19 /T echD OC/Se ning /08-Mess a nlag en/D O K-347_CM3/2:Inbetriebnahme@ 7\mod_1422969500154_19.docx@126309@ 2 @ 1
2.2 Initial Operation
The CM3 is factory tested and calibrated.
The device must be fitted with suitable couplings to connect to the discharge system of the
tank truck.
IMPORTANT:
Before operating the device for the first time, read the instructions for
use carefully and follow them.
Pos: 20 /T echD OC/Se ning /08-Mess a nlag en/D O K-347_CM3/|2--->> Messb etri eb @ 7\mod_1422969732828_19.docx@ 126331@ 2 @ 1
2.3 Measurement Operation
Pos: 21 /T echD OC/Se ning /08-Mess a nlag en/D O K-347_CM3/3:Ankuppeln/Abkuppeln@ 7\mod_1422969801624_19.docx @ 126353@ 3@ 1
2.3.1 Coupling/ Uncoupling
Connect the CM3 to the discharge coupling on the tank truck.
Orientate the CM3 so that the display can be read easily.
Make sure that the gaskets in the couplings are in good condition to prevent leakages.

MN F08 001 EN  DOK-347E  Issue/Rev. 1.10 (01/15) CN3

Device description
Sening®is a registered trademark of FMC Technologies 9
Pos: 22 /T echD OC/Se ning /08-Mess a nlag en/D O K-347_CM3/3:Bedienelemente@ 7\mod_1422969907938_19.docx @ 126375@ 3@ 1
2.3.2 Controls
The CM3 is shipped from the factory fully operational. For operation only the display panel
and the three keys on the operating panel are relevant.
Pos: 23 /T echD OC/Se ning /08-Mess a nlag en/D O K-347 _CM34: A nzeig e/ Ta stat ur@ 7\mod_1423153151317_19.docx @ 126813@ 44@ 1
2.3.2.1 Display
Two values are shown on the display.
The upper value is the discharged in litres
(total).
The lower value (smaller figures)
indicates the momentary flow rate in litres
per minute (
 /min).
2.3.2.2 Keypad
The CM3 has a total of three keys.
Pressing the left key (ACCUM. TOTAL) displays the total „accumulated“ discharge
volume on the upper display in litres. This value is only visible while the key is pressed.
This value is not resettable.
The central key (RESET)is used for zeroing the display. Once the key is pressed,
the CM3 display is set to zero.
The right key (PROG)is only used for programming the CM3. Since this procedure
is carried out by the manufacturer, this key has no significance for the operation of the
CM3.
The device has no ON/OFF switch. It always remains ready for operation. The current
consumption is minimised by an internal circuit for maximum battery lifetime.
3
2
1
1
2
3

CN3

Device description MN F08 001 EN  DOK-347E  Issue/Rev. 1.10 (01/15)
10 Sening®is a registered trademark of FMC Technologies
Pos: 24 /T echD OC/Se ning /08-Mess a nlag en/D O K-347 _CM3 /3 : M eß vorg ang @ 7\mod_1422971523452_19. docx@ 126419@ 3@ 1
2.3.3 Measurement Procedure
Measurement with the CM3 shall be carried following this procedure:
Step 1:
Check the interior for contamination or damage.
The impeller must turn easily and then stop abruptly.
Step 2:
Check the display; the upper and lower displays must indicate zero.
If the upper display indicates a value,
press the <RESET> key.
The display should now indicate zero.
Step 3:
Connect the CM3 to the discharge coupling on the vehicle.
Couple the discharge hose to the meter and the filling nozzle ().
The measurement process can now be started.
Step 4:
After discharge remove the product hose and disconnect the CM3 from the discharge
coupling. Place the device safely in its storage location.
Be sure that that no fuel flows into the environment

MN F08 001 EN  DOK-347E  Issue/Rev. 1.10 (01/15) CN3

Device description
Sening®is a registered trademark of FMC Technologies 11
Pos: 25 /T echD OC/Se ning /08-Mess a nlag en/D OK-347_CM3/|2--->>Lag er ung @ 7\mod_1422972241504_19.docx@ 126441@ 2 @ 1
2.4 Storage
Pos: 26 /T echD OC/Se ning /08-Mess a nlag en/D O K-347 _CM3 /3 : H alter u ng i m F ahr zeug @ 7 \mod_1422972313405_19.docx @126463@ 3 @ 1
2.4.1 Storage bracket in the vehicle
The CM3 should be stored in a special vibration-absorbing storage device on the tank truck.
Storage device example for model CM3:
Pos: 27 /T echD OC/Se ning /08-Mess a nlag en/D O K-347 _CM3 /Gr afi k: CM3 mi t H al ter ung @ 7\mod_1422972652174_19.docx@ 126485@ @ 1
Removal direction
Pos: 28 /T echD OC/Se ning /08-Mess a nlag en/D O K-347 _CM3/3 : Entn ahme a us der Halt erung @ 7\mod_1422972916516_19.docx@ 126507@ 3 @ 1
2.4.2 Removal from the holder CM3-AV
Loosen the coupling on MK CM3; while you hold the CM3 with the other hand firmly at the
handle.
Slide the CM3 on the bearing pin back and turn it at the same time by about 45 °.
Now the CM3 can be removed from the mandrel.
Pos: 31 /T echD OC/Se ning /Wart ung/|1---> Wart ung @ 0\mod_1309780689484_19.docx@ 9644 @ 1 @ 1

CN3

Maintenance MN F08 001 EN  DOK-347E  Issue/Rev. 1.10 (01/15)
12 Sening®is a registered trademark of FMC Technologies
3 Maintenance
Pos: 32 /T echD OC/Se ning /Wart ung/W artung ( CM3) @ 7\mod_1423139254910_19.docx@ 126560@ @ 1
The CM3 has been designed for minimum requirements. Each time the meter is used, it
must be checked whether the meter impeller wheel turns easily.
Lubrication of the impeller bearing is provided by the measured fluid. Therefore never
blow out the CM3 with compressed air. Damage to the bearing may occur.
With the CM3 regular safety inspections must be carried out, according to ElexV. §12
and VBG 4.
Pos: 33 /T echDO C/Seni ng/W artung /2: Wart ung Batt erie wechsel (C M3) @ 7\mod_1423146988522_19.docx@ 126590@ 2 @ 1
3.1 Battery Replacement
When the battery service life expires, after about 2 years, this is indicated on the display with
low bat.
The batteries must be replaced when the low bat indication appears in the display.
Important:
The CM3 is a so-called intrinsically safe component and is approved with regard to the
explosion protection. Therefore only genuine replacement batteries must be used.
The voltage supply for the CM3 is provided by two batteries.
Only one battery must be replaced at a time, because otherwise all the settings
will be deleted.
Unscrew the four mounting screws on the membrane keypad to change the batteries.
Then remove the membrane keypad and place it on a clean surface.

MN F08 001 EN  DOK-347E  Issue/Rev. 1.10 (01/15) CN3

Maintenance
Sening®is a registered trademark of FMC Technologies 13

The connecting lead to the sensor is
of sufficient length and does not need
to be removed.

Now pull off the connecting lead
between the battery and electronics.

Fit the new battery.

Ensure that the batteries are firmly
mounted with the appropriate cable
ties.

If the cable ties are not pulled
tight,
damage may occur later in operation.
Pos: 34 /T echD OC/ Seni ng /Tec hni sc he D ate n/|1---> Techni s che D at en @ 0\mod_1309780695828_19.docx @ 9748@ 1 @ 1

CN3

Technical Data MN F08 001 EN  DOK-347E  Issue/Rev. 1.10 (01/15)
14 Sening®is a registered trademark of FMC Technologies
4 Technical Data
Pos: 35 /T echD OC/Se ning /Tech nisc heD ate n/2: Tec hnisc he Daten C M3 @ 7\mod_1423147451370_19.docx@ 126612@ 2@ 1
4.1 CM3
Operating temperature:
- 20 °C to + 60 °C
Permissible pressure:
10 bar
Dimensions:
Depending on product variant
Material (in medium contact):
Aluminium; stainless steel
Weight:
approx. 8 kg, depending on product variant
Measurement range:
250 -2000

/min
Measurement accuracy: +/- 5 % in above measurement range at viscosities
between 0.6 and 5 mm
2
/s
Liquids: Low-viscosity petroleum products;
(gasoline, kerosene and diesel)
Dimensions (incl. Halterung):
170 mm wide; 400 mm high; 500 mm long
Voltage supply:
Two lithium batteries ***)
Battery service life:
about 2 years
Display:
LCD display
Total:
7 -figure display; 10 mm high
Accumulated total:
( Akkum. Totals)
see above
Flow rate:
4-figure display; 8,5 mm high
Splash-proof:
Conforming to IP 65
***) As a substitute may be used only explosion-proof batteries type xxxxx.
Refer to the Note: battery change (see chapter 3.1 "Battery Replacement" / page 12).
Pos: 37 /T echD OC/Se ning /Wart ung/2: W artung R epar atur u nd Ersat ztei le( CM 3)_E @ 7\mod_1423744279863_19.docx@ 126951@ 2 @ 1
4.2 Repairs and Replacement Parts
Repairs to the impeller or the electronics must only be carried out by the manufacturer.
Replacing the internal electronics requires a re-calibration of the measuring element.
Only replacement parts from F. A. Sening must be used: An overview of the available
replacement parts is given in the Replacement Parts Drawing:
•CM3 / 51.250223 (see Appendix 17) and for
•CM3-AV / 51.250243 (see page 18).
Pos: 38 /T echD OC/Se ning /Allg emein/| 1---> Ansc hrift u ndK onta kt @ 0\mod_1307366798125_19.docx@ 5888@ 1 @ 1

MN F08 001 EN  DOK-347E  Issue/Rev. 1.10 (01/15) CN3

Address and contact details
Sening®is a registered trademark of FMC Technologies 15
5 Address and contact details
Pos: 39 /T echD OC/Se ning /Allg emein/ Ansc hrift un d Konta kt @ 3 \mod_1358149758511_19.docx@ 71170 @ @ 1
Our service department will be happy to assist and can be contacted as follows:
Measurement Solutions
F. A. Sening GmbH
Regentstrasse 1
D-25474 Ellerbek
Tel.: [phone] - 0 (Switchboard)
Fax: [phone] - 152 (Service)
Fax: [phone] - 133 (Sales)
Fax: [phone] - 255 (Order processing)
E-Mail: [e-mail]
Web: www.fmctechnologies.com/seningttp
Pos: 40 /T echD OC/Se ning /Zeic hnung en/|A---> Zeic hnu ngen und Z ul ass ung en @ 0\mod_1310131619941_19.docx@ 10030 @ @ 1

CN3

Address and contact details MN F08 001 EN  DOK-347E  Issue/Rev. 1.10 (01/15)
16 Sening®is a registered trademark of FMC Technologies
Appendix A. Drawings and Approvals
Pos: 42 /T echD OC/Se ning /08-Mess a nlag en/DOK-347 _CM3 /Ta bel le: Zeic hnu nge n un d Zul ass ung en C M3 _E @ 7\mod_1423743007641_19.docx@ 126928@ @ 1
Drawings No. Page
Turbine Check Meter - CM3
51.250223
17
Holder – CM3-AV
51.250243
18
Turbine Check Meter model CM3-E
Turbine Check Meter model CM3-K3
Turbine Check Meter model CM3-K4
Holder CM3-AVK4
Certificates
KEMA_Certificate_ Of_Conformity_CM3 KEMA
19
Table 1: Drawing Overview
Pos: 43 /T echD OC/ Seni ng/H ist orie-Hin weis-Doku ment e/DOK -000_Hinweis:DokumentationZeichnungenAlsPDFInternet @ 6\mod_1394027360978_19.docx@ 115376@ @ 1
Documentation and drawings as PDF files on the Internet:
www.fmctechnologies.com/seningttp
=== En de der Lis te für Te xtmar ke Inhal t= ==
Index .
A
Application Information.................7
C
CM3................................6, 7, 8, 10
F
Functional Principle......................8
I
impeller.......................................10
M
Manufacturer................................ 6
measurement operation............... 7
Measurement Procedure........... 10
O
operating panel............................ 9
P
Pictograms................................... 5
S
Safety regulations ........................6
Service department....................15
splitted..........................................7
V
vibration-absorbing ....................11

Sening®is a registered trademark of FMC Technologies MN F08 001 EN  DOK-347E  Issue/Rev. 1.10 (01/15) 17
Pos: 46 .1 /Tec hDOC/ Seni ng/Zei chnu ngen/| FZ1---> Z eic hnu nge n @ 0 \mod_1309780698375_19.docx@ 9826 @ @ 1
Drawings
Pos: 46 .2 /Tec hDOC/ Seni ng/Zei chnu ngen/D OK-347_CM3/51.250223– Tur bine nzähl er -CM 3(Ne w)@ 7\mod_1423736555294_19.docx@126880@ @ 1
51.250223 – Turbine Check Meter - CM3

18 MN F08 001 EN  DOK-347E  Issue/Rev. 1.10 (01/15) Sening®is a registered trademark of FMC Technologies
Pos: 46 .3 /Tec hDOC/ Seni ng/Zei chnu ngen/D OK-347_CM3/51.250243– Aufnahmeeinrichtung– CM3-AV (New) @ 7\mod_1423736603412_19.docx@ 126903@ @ 1
51.250243 – Holder – CM3-AV

Sening®is a registered trademark of FMC Technologies MN F08 001 EN  DOK-347E  Issue/Rev. 1.10 (01/15) 19
Pos: 47 /T echD OC /Se ni ng/ Kon for mit äts er klär ung en /|F Z1---> Zul assu ngen @ 0\mod_1308137651118_19.docx @ 8404@ @ 1
Approvals
Pos: 48 /T echD OC/Se ning /Kon for mit äts er klär ung en /K EMA _C erti fica te _ Of _Co nf or mit y_CM 3 @ 7\mod_1423150009802_19.docx@ 126768@ @ 1
KEMA - Certificate Of Conformity
=== E nde d er List e für T e xtmar ke Z eic hnu nge n == =

Pos: 50 /T echD OC/Se ning /Intro' s/L etzte Sei te/I ntro: S ENING Vertri ebAdr ess en @ 0\mod_1307366798484_19.docx@ 5901 @ @ 1
=== E nde d er List e für T e xtmar ke I ntr o_ Letzt eS eit e ===
The specifications contained herein are subject to change without notice and any user of said specifications should verify from the manufacturer that the specifications are
currently in effect. Otherwise, the manufacturer assumes no responsibility for the use of specifications which may have been
changed and are no longer in effect.
Contact information is subject to change. For the most
current contact information, visit our website at www.fmctechnologies.com/measurementsolutions and click on the
“Contact Us” link in the left
-hand column.
Headquarters:
500 North Sam Houston Parkway West, Suite 100 Houston, TX 77067 USA, Phone: [phone], Fax: [phone]
Measurement Products and Equipment:
Eri
e, PA USA [phone]
Ellerbek, Germany
[phone]
Barcelona, Spain
[phone]
Beijing, China
[phone]
Buenos Aires, Argentina
[phone]
Burnham, England
[phone]
Dubai, United Arab Emirates
[phone]
Los Angeles, CA USA
[phone]
Melbourne, Australia
[phone]
Moscow, Russia
[phone]
Singapore
[phone]
Integrated Measurement Systems:
Corpus Christi, TX USA
[phone]
Kongsberg, Norway
[phone]
San Juan, Puerto Rico
[phone]
Dubai, United Arab Emirates
[phone]
Visit our website at
www.fmctechnologies.com/measurementsolutions
Printed in Germany ©
10/15 F. A. Sening GmbH, Inc. All rights reserved. MN F08 001 EN / DOK-347E Issue/Rev. 1.10 (01/15)