2. When the heating mode, when press the sleep button to enter sleep mode, an hour later, the set temperature automatically reduce 1°C,
2 hours later, the set temperature automatically reduce 2°C.
3. Press the sleep button again to exit the sleep function.
Note: in sleep mode, the wind speed will be locked in low wind and the temperature can not be adjusted.
TIMER:
1. You can set the timer on/off. Timing start up: after setting timing start up, the machine will automatically start up and run when the timing
time arrives. In standby mode, press the timing key, and the corresponding timing indicator time value flashes.The timing time can be
adjusted by adjusting the temperature up and down key (step distance is 1 hour), and the time interval range can be set as 1~24
hours.Finally, press this button to start timing. At this time, the timing indicates that the time value is always on, and the display displays
the remaining time.
1.1.The machine will automatically start up and run after the timing time is set.
1.2. If you want to cancel the timing function, you can press this button again.
1.3.If the set timing boot time is not reached, press the ”on/off” button in advance, the timing will be cancelled, and the machine will start
up and run at the same time.
2. Regular shutdown: after regular shutdown is set, the machine will automatically stop running when the regular time is reached.
2.1.In the boot state, press the timing button, and the corresponding timing indicator time value flashes.The timing time can be adjusted
by adjusting the temperature up and down key (step distance is 1 hour), and the time interval range can be set as 1~24 hours. Finally,
press this button to start timing, and the timing LED will always be on;The digital tube displays the current set temperature.
2.2. The machine will shut down automatically when the timing time is set.
2.3. If you want to cancel the timing function, you can press this button again.
2.4. If the set timing shutdown time is not reached, press the ”on/off” button in advance, the timing will be cancelled, and the machine will
be shut down and stop running.
ON/OFF:
1. Press ”on/off” to start up, and then press ”on/off” to shut down.
WIND:
1. Press the swing wind button to start the swing wind function; Press the swing button again, and the left and right swing function will be
cancelled.
TEMP-:
1. Under cooling and heating function, set in the range of 16 ~ 31 °C temperature. Every click on the temperature, set temperature reduced
by 1 °C.
TEMP+:
1. Under cooling and heating function, set in the range of 16 ~ 31 °C temperature. Each press keys on temperature, set temperature
increase 1 °C.
MODE:
1. Press the mode key to perform mode conversion and select one of the operation modes of ”refrigeration, dehumidification, air supply,
heating , and automation”.
1.1.Cooling operation: Press the mode key until the refrigeration indicator is on, and select the refrigeration function. While the
refrigeration function is in progress, extend the bar Put the tube out of the window so that hot air can escape from the room. According to
the temperature rise or lower key can adjust the set temperature, the temperature range of 16-31 °C / 61 ~ 88 °F. Press the wind speed
button to select one of the high, medium and low wind speeds. Note: In order to improve the cooling capacity of the machine, please note
the following: A) if the room is in direct sunlight, please close the curtains. B) do not place the machine where there is a heat source.
Depending on the rate of in which room is heating up and its size it might be not possible to cool it down to selected temperature.
1.2.Dehumidifying operation: Close the doors and Windows when using the machine to prevent excess moisture from entering the
room. Press the mode key, the dehumidification indicator will light up, and the display screen will display dH, and select the
dehumidification function. In this mode, the wind speed is not adjustable, the default low speed. In the case of selecting dehumidification
mode, expansion tube is not required.
1.3.Fan operation: Press the mode key, the display will display FA, and select the function of air supply. Press the wind speed button to
select one of the high, medium and low wind speeds.
1.4.Automatic function: Press the mode key, the automatic light will turn on and select the automatic function.The machine can
automatically select appropriate functions according to the set temperature.
Temperature display conversion:
1. Press both the temperature - and + keys, and the display will switch between Fahrenheit and Celsius.
OPRÓŻNIANIE ZBIORNIKA NA SKROPLINY / PROCEDURE FOR EMPTING WATER TANK
1. Jeśli na wyświetlaczu zaświeci się komunikat „E3" urządzenie przestanie pracować i
konieczne jest opróżnienie zbiornika na skropliny. By to zrobić należy wyjąć gumową
zaślepkę z wylotu zbiornika (A) i spuścić z niego wodę. Po jego całkowitym opróżnieniu należy
ponownie zaślepić otwór zaślepką i zrestartować urządzenie by wznowiło pracę.
1. When the tank is full, “E3”will be displayed on the display panel. Please remove the rubber cap
(A) from the drainage hole to drain out the water. After the drainage is completed, please
restart the unit and then the unit can operate normally.
8
A
PL
EN
