Focal IMPULSE 4.320 User manual

IMPULSE 4.320
Ultra-compact D-class amplifier
User manual / Manuel d'utilisation
English page 3
Français page 15
Deutch seite 27


Thank you for choosing Focal amplifiers for your Car Audio system and for sharing our philosophy: “the Spirit of
Sound”. This product offers the best of Focal technology in terms of compact D-class amplifiers.
In order to obtain the best results, we highly recommend you have your IMPULSE 4.320 amplifier installed by
your local Focal dealer. To maximise the use of all the functionalities of your amplifier and to fully enjoy its
performance, we recommend you thoroughly read all the instructions in this manual and keep it for future
reference. Any problems due to the non-compliance of these rules may void the warranty.
CAUTION
This symbol indicates important instructions. Failure to comply with these instructions may result in
injury or material damage.
Contents
- IMPULSE 4.320 amplifier
- User manual
- Set of accessories
Accessory available (sold separately):
- 1 ISO Plug and Play cable for connecting up to compatible head units
The Focal guarantee only applies if the enclosed guarantee card
is returned to us within 10 days of purchase.
English version
Your Focal-JMlab product was developed and manufactured with high-quality materials and components
which can be recycled and/or re-used. This symbol indicates that electrical and electronic equipment
must be disposed of separately from normal garbage at the end of its operational lifetime.Please dispose
of this product by bringing it to your local collection point or recycling centre for such equipment. This will
help to protect the environment in which we all live.
IMPULSE 4.320 AMPLIFIER
User manual
CAUTION
• Do not operate any functions which may distract you while driving. Functions or settings requiring sustained
attention must only be used when the vehicle is at a complete standstill. Always make sure to stop your vehicle in
a safe place before operating these functions. Failure to do so may cause an accident.
• Keep the volume at a low level to be able to hear outside noises while driving the vehicle. Failure to do so may
cause an accident.
• Never open your IMPULSE 4.320 amplifier and never make any modifications to the product. Failure to do so may
cause an accident, a fire or an electric shock.

4
IMPULSE 4.320 aMPLIfIEr
User manual
CAUTION
• Only use your IMPULSE 4.320 amplifier with 12V mobile applications. Any use other than the intended use may
cause a fire, an electric shock or injury.
• Use fuses with the adequate amperage. Failure to do so may cause a fire or an electric shock.
• Do not obstruct the heat sink on your IMPULSE 4.320 amplifier. Internal overheating may occur and cause a fire.
• Wire the connections correctly. Make sure you use the appropriate wire gauge and type of cable. Failure to do so
may cause a fire, injury and/or material damage.
• Do not use nuts or bolts on steering or breaking systems, tanks, seat-belt anchor points or other safety
elements for connecting the ground. Use of these parts as ground may deactivate the vehicle’s control system
and cause a fire or other technical problems.
• Keep all small objects which could be swallowed, such as fasteners, screws and accessories, out of the reach of
children. Swallowing such objects may cause serious injuries. If swallowed, seek medical advice.
• Before beginning installation, disconnect the negative terminal of the battery to avoid any risk of injury, fire or
material damage (fig. 1).
fig. 1
WARNING
Prolonged listening at high volumes, over 110dB, can cause long-term damage to your hearing. Listening at
volumes over 130dB, even for short periods of time, can cause permanent damage to your hearing.
Stop operation in the event of a problem. Failure to comply with this precaution may cause injury or material
damage. If a malfunction persists, return the equipment to your Focal dealer for repair.
Use the specified accessories and be sure to install them correctly. Only use the accessories specified in the user
manual and those which are supplied in the packaging. The use of other components could cause internal damage
to the equipment, or it may not be correctly installed. The parts used may become loose and cause damage or a
technical malfunction of the equipment. Failure to do so may cause an accident, a fire or an electric shock.
Do not install this product in very humid or dusty places. Avoid installing the equipment in places with high levels of
humidity or with an excessive presence of dust. Humidity or dust getting inside the product may cause a technical fault.

5
IMPULSE 4.320 aMPLIfIEr
User manual
Installing your IMPULSE 4.320 amplifier
Installation of this product requires technical knowledge and experience. If you are uncertain of your ability to
correctly install the amplifier, we strongly recommend you contact your Focal dealer who will install it for you, so
that you will be able to take full advantage of the full capabilities of your IMPULSE 4.320 amplifier.
Wiring your IMPULSE 4.320 amplifier
Only use the wiring harnesses recommended in this manual and the accessories supplied.
Use the ISO cable (sold separately) to facilitate wiring. The speaker driver cable must ONLY be used for connecting
the amplifier to the speaker drivers. The wire gauge of power cables must correspond with those indicated in the
table (paragraph 3.1) and depends on the power of your amplifier and the length of cable required. Use double or
triple shielded RCA cables to avoid any interference of the low-level signal.
Operating time of your IMPULSE 4.320 amplifier
Avoid using the amplifier for extended periods of time without starting the vehicle. This may cause the battery to run
flat prematurely.
Cooling system
Do not cover the top of your IMPULSE 4.320 amplifier as this may cause overheating.
Materials required for installation (in addition to accessories supplied)
• 2 sheaths of adequate cross-section (1 sheath for the power cable, 1 sheath for the speaker driver, REMOTE and
RCA modulator cables)
• Multimetre (voltage/amperage)
• Soldering iron + solder
• Crimpers
• Wire stripper
• Wire cutter
• Battery terminal spanner
• Hand drill and assorted drill bits
• Heat-shrink tubing of adequate diameter for the different cables
• Power cable of adequate length and wire gauge
• Remote turn-on cable (REM input on amplifier) of adequate length and wire gauge
• Ground cable of suitable length and wire gauge
• Fuse holder and suitable fuse
• Spade terminal for connecting to positive (+) battery terminal
• Spade terminal for connecting to the chassis of the vehicle (-).
• Screw with minimum 015⁄64" (6mm) screw head and its nut for ground connection to the chassis of the vehicle
Installation
The following section deals with issues related to the vehicle which must be considered for before installing your
amplifier. You will save time by planning the layout of the system and wiring in advance.
During this preparatory time, please ensure that all the settings remain accessible once the installation is complete.

6
IMPULSE 4.320 aMPLIfIEr
User manual
Before beginning the installation, please follow these rules carefully:
1 - After thoroughly reading the user manual, make sure you have understood all the instructions before installing
your amplifier.
2 - Disconnect the battery’s negative wire before installation (fig.1).
3 - To facilitate assembly, we strongly recommend you unwind all the wires before installing your amplifier.
4 - Route all RCA, speaker driver and REM cables, away from the power cables in order to avoid any signal interference.
5 - Use quality connectors/splicing or good soldering for connecting the amplifier in order to ensure a reliable
installation and to minimise any loss of signal or power.
6 – Before carrying out any operations, be extremely careful not to cut or drill through the fuel tank, fuel, brake,
hydraulic or vacuum lines, any electrical wiring or safety devices.
7 - Never route a wire under the vehicle. Wiring must be installed inside the vehicle. When routing the cables, make
sure they do not impede your driving. Cables obstructing or routing through areas such as the steering wheel,
pedals (brake, accelerator and clutch, etc.) may be extremely dangerous.
8 - Avoid routing wires over or through sharp edges. Any wire routed through metal must be protected with a
grommet. Route the cables well away from mobile parts (seat rails,…) and from sharp or pointed edges. This will
avoid getting the cables caught or damaging the cables which may cause a short circuit.
9 - Always protect the battery and electric circuit from potential damage using fuses. Install a fuse holder and
adequate fuses on the 12V positive (+) power cable less than 15" (40cm) away from the battery terminal. Ideally,
this above-mentioned distance should be as short as possible (fig.10).
10 - Prepare the chassis ground by scraping off any traces of paint on the metal surface in order to ensure proper
grounding. The grounding connections should also be as short as possible and ALWAYS be connected to metal
welded to the body or the chassis of the vehicle (fig.2). The ground point which is generally chosen is the one
connecting the negative terminal of the battery to the chassis of the vehicle.
11 - NEVER INSTALL this product in the engine compartment of the vehicle. This will void the warranty.
1 – Positioning of your IMPULSE 4.320 amplifier
Where to install your IMPULSE 4.320 amplifier?
Due to the power of the amplifier, heat dissipation is required for correct operation. For this reason, the amplifier,
particularly the top, must be installed in a well-ventilated area. Avoid covering or embedding the amplifier in its
installed location.
2 – Mounting your IMPULSE 4.320 amplifier
Position your amplifier at the desired location and make matchmarks.
Locate the attachment points on your support using the mounting bracket supplied.
Use screws suitable for your type of support.
3 – Wiring your IMPULSE 4.320 amplifier
CAUTION
If you are uncertain of your ability to correctly install the amplifier and to wire the system up properly, get
a Focal dealer/installer to do it for you.

7
IMPULSE 4.320 aMPLIfIEr
User manual
WARNING
Avoid routing power cables close to low-level input cables (LOW-LEVEL INPUTS) and high-level input
cables (HIGH-LEVEL INPUTS), close to the car aerial or close to sensitive equipment and harnesses.
High-current power supply cables can cause static/interference that affects audio signals.
WARNING
Keep the cables as short as possible to optimise the quality of the installation. This will also limit signal
loss.
WARNING
Before beginning the connection phase, remove the negative (-) terminal from the battery of the vehicle
(fig.1).
3.1 - What wire gauge should I use for the power cable?
Your IMPULSE 4.320 amplifier requires a power supply of adequate amperage.
The required wire gauge of power cables depends on the length of cabling to the battery. See recommended wire
gauge in the table below:
Length of cable to the battery in feet (metres)
Length < 3ft (1m) < 10ft (3m) < 13ft (4m)
Cross sectional area in mm2
ISO cable recommended 3.3mm2> 3.3mm2
AWG 12 AWG < 12 AWG
Compliance with these wiring rules is essential for the safety of your electrical installation, and important for
maintaining maximum performance of your IMPULSE 4.320 amplifier.
3.2 – Wiring the input and output signals on your IMPULSE 4.320 amplifier
3.2.1 – Your head unit is equipped with RCA outputs
Route the modulator cables (RCA), the speaker driver cables and the REM cable together, ensuring to isolate them
from other powerful automobile accessories, particularly electric motors (windscreen wipers,…). Keep the whole
length of the cables, which will be adjusted later on.
3.2.2 – Your head unit is only equipped with amplified outputs (speaker driver outputs).
Route the modulator cables coming from the head unit, and the speaker driver cables together, ensuring to isolate
them from other powerful automobile accessories, particularly electric motors (windscreen wipers,…). Keep the
whole length of the cables, which will be adjusted later on.
3.3 – Wiring the power supply to your IMPULSE 4.320 amplifier
3.3.1 – Route the positive power cable (+) making sure when doing so to route the cable to the opposite side of the
cables that you have previously installed to avoid any interference. DO NOT CONNECT THE CABLE YET.

8
IMPULSE 4.320 aMPLIfIEr
User manual
3.3.2 – Get the negative power cable (-). This cable should be as short as possible and ideally shouldn’t be any longer
than 3ft (1m), to ensure a perfect connection between the amplifier and the chassis of the vehicle. The cable and wire
gauge must comply with the table in section 3.1. Find a suitable grounding point, then sand it to remove any traces
of paint or other coating in order to optimise the quality of the contact point. Drill a hole in the metal that you have
previously sanded, making a hole the same diameter as the screw you are using, making sure that there are no fuel
lines, cables or any other sensitive vehicle devices nearby. Solder the ground cable to the wiring harness supplied for
your IMPULSE 4.320 amplifier and isolate using heat-shrink tubing (fig. 2).
3.4 – Connecting the input signals to your IMPULSE 4.320 amplifier
You can now start connecting the input/output cables.
3.4.1 – Your head unit is equipped with RCA outputs
Connect the RCAs to the RCA adapter cable supplied (fig. 3). Be careful to respect the polarities (INPUT Left = red, INPUT
Right = black or white) and distribution (F=FRONT, R=REAR). Connect the other end to the amplifier’s INPUTS panel.
fig. 2
fig. 3
Switch the INPUTS LEVEL to LOW (fig. 4).
fig. 4

9
IMPULSE 4.320 aMPLIfIEr
User manual
3.4.2 – Your head unit is only equipped with amplified outputs (speaker driver outputs).
Connect the speaker driver outputs of the head unit directly to the adapter cable supplied (fig. 5) ensuring the pola-
rities are respected. Connect the other end to the amplifier’s INPUTS panel.
fig. 5
Switch the INPUTS LEVEL to HIGH (fig. 6).
fig. 6
3.5 – Connecting the speaker drivers and remote to your IMPULSE 4.320 amplifier
Solder the REMOTE cable to the wiring harness supplied and isolate using heat-shrink tubing (fig. 7).
Connect the other end of the REMOTE cable to the car radio REMOTE terminal.
fig. 7

10
IMPULSE 4.320 aMPLIfIEr
User manual
Finally, connect the speaker driver cables to the amplifier, making sure the polarities on the wiring harness supplied
are respected (+ with +; - with -) (fig. 8).
fig. 8
WARNING
The speaker drivers or speaker driver kits wired to your IMPULSE 4.320 amplifier must systematically have a mini-
mum impedance of 2 Ohms.
WARNING
In bridged mode, the speaker drivers or speaker driver kits wired to your IMPULSE 4.320 amplifier must systemati-
cally have a minimum impedance of 4 Ohms.
The use of equipment with a lower impedance will void the warranty.
To use the IMPULSE 4.320 in bridged mode, and thus double the power available, make sure that connections and
polarities are respected as shown below (fig. 9)
fig. 9

11
IMPULSE 4.320 aMPLIfIEr
User manual
WARNING
The cable connecting the positive (+) terminal of the battery to the “+ BATT” terminal on the amplifier MUST be fused
(ampere rating: 25 amperes) at less than 15" (40cm) away from the battery of the vehicle.
The connections on the fuse-holder must be fully insulated.
Open the fuse holder, removing the fuse with care. Fix the fuse holder’s base.
Cut a length of power cable measuring between 4" and 15" maximum (10 and 40cm). Strip 025/64" (1cm), then tin.
Screw the cable to the terminal of the fuse holder (battery side). Crimp the power cable to the intended spade
terminal and screw to battery terminal.
Strip 025/64" (1cm) from the remaining length of cable, then tin. Screw the cable to the other fuse holder terminal.
Solder the positive (+) power cable to the wiring harness supplied for your IMPULSE 4.320 amplifier (fig. 10)
3.6 – Start-up and checks.
The connection phase is now complete. You must now check that the power supply is correct and that everything
is working correctly (head unit/amplifier/speaker drivers). Set the source gain to its minimum. Set the gain on
your amplifier to 1/3 of the way. Turn on the various devices. Once all the devices have been turned on, test your
installation at low volume.
.
40cm max
fig. 10

12
IMPULSE 4.320 aMPLIfIEr
User manual
4 - Control panel and connections
fig. 11
INPUTS: These connectors are dedicated to the low-level and high-level signal inputs.
GAIN (FRONT AND REAR): The GAIN knob allows you to adjust the incoming signal to the amplifier. The voltage gain
varies between 0.2V and 5V. To optimise the performance of your sound system, you need to apply a maximum of gain
as early as possible in the stereo system, and then a minimum of gain afterwards.
This knob must be set according to the source volume (line output level).
Start by setting the amplifier gain to its lowest level. Gradually increase the level of the source volume up to 3/4
of the way. Then increase the amplifier gain to the desired maximum listening volume. Turn the volume down if
distortion occurs. The FRONT knob controls the front speaker drivers. The REAR knob controls the rear speaker
drivers.
+12V: the “+BATT” power connector is dedicated to the power cable connecting the amplifier to the positive (+)
terminal of the battery.
GND: the GND (ground) power connector is dedicated to the negative (-) power cable connecting the amplifier and
the vehicle’s chassis.
REM: the REM connector connects the amplifier to the source (head unit) via a REM or REMOTE output on the head
unit. This enables the amplifier’s automatic power on function when the source (head unit) is turned on.
POWER and PROTECT: these LEDs enable you to check if the amplifier is working correctly.
A continuously lit POWER LED means the equipment is working correctly.
If the PROTECT LED is continuously or intermittently lit, the equipment is not working correctly. See troubleshooting
section paragraph 5.
INPUTS LEVEL: this switch selects the type of input level (HIGH: high-level / LOW: low-level RCA)

13
IMPULSE 4.320 aMPLIfIEr
User manual
5 – Troubleshooting
The state of the various LEDs indicates a malfunction or the source of a malfunction.
Check the possible causes shown below. If, despite these checks, the equipment is still not working correctly, contact
your IMPULSE 4.320 amplifier installer or dealer.
State of LEDs Presence of
sound
Possible cause Action
PROTECT
lit red
NO Output short
circuit
Turn off the sound system.
Check the speaker drivers, their minimal impedance,
their connections and the speaker driver cables.
Off NO No power or
poor
connection
Turn off the sound system.
Check power source is 12V.
Check the power cables and their polarity.
Check the fuses.
Off NO Overheating Turn off the sound system.
Wait for your amplifier to cool down before resuming use.
Off NO No REM signal Turn on the sound system.
Check there’s power on the REM terminal.
Off NO Fuse
malfunction
Turn off the sound system.
Check and replace the fuses if necessary.
POWER
flashing green
YES/NO
Or intermittent
Grounding
defect
Turn off the sound system.
Check the connection from the GND terminal
to the chassis of the vehicle.
INPUT SELECT: this switch enables channels 1 and 2 to be played through channels 3 and 4.
If you only have one output (one right and one left), you can still amplify the four channels by activating the 1/2 mode.
If you want to use the IMPULSE 4.320 with its independent 4-channel input configuration, select mode 3/4.
If you want to use the IMPULSE 4.320 with a 3-channel configuration, select mode 1+2. Channels 3/4 will then receive
the mono signal from channels 1 and 2 to drive your subwoofer.
PHASE (°): the PHASE knob enables you to adjust the channel phase according to the rest of the installation.
Adjusting the phase of the subwoofer enables the subwoofer output to be in phase with the other speaker drivers. On
a theoretical period of a signal, one of the sources can be delayed slightly so that the phase will be perfectly balanced
at the listening point.
X-OVER MODE: the crossover mode switch enables you to choose to activate the high-pass filter mode (HPF), the
low-pass filter mode (LPF) or the full range mode (FULL) for channels 3/4 or rear channels.
X-OVER FREQ (Hz): this knob controls the cut-off frequency by adjusting the low-pass and high-pass filter levels. The
selected value determines the frequency up to which or from which the signal will be cut off.
FRONT CH. (1/2): this switch activates a high-pass filter set at 75Hz for the front channels. Use this setting for solving
issues related to door vibrations in vehicles not equipped with vibration dampeners.

14
IMPULSE 4.320 aMPLIfIEr
User manual
6 – Technical specifications
IMPULSE 4.320
4/3/2-channel class D amplifier
High-level input / RCA low-level input √
CEA power (4 Ohms) 4 x 55Wrms
Power max (2 Ohms) 4 x 80Wrms
Power max (4 Ohms bridged) 2 x 160Wrms
Bandwidth 10Hz – 20KHz (+/- 1dB)
Total harmonic distortion THD+N < 0.05 % from 0.5 to 50Wrms 4Ω (1 kHz, 22kHz LPF)
Total minimum harmonic distortion 0.02 %
Cross-talk (1KHz) > 65dB (Ref. 10 Vout)
SNR (1W/A) > 80dBA
High-pass filter Activatable/deactivatable fixed at 75Hz on channels 1/2
High-pass/low-pass filter configurable from 40Hz - 200Hz on channels 3/4
Phase Adjustable 0/180° on channels 3/4
Full range mode on channels 1/2 and 3/4
Standby consumption – (Remote ON) 750mA
Fuse ratings 25A (15A if ISO harness)
Protection Short circuit/over-current/reverse polarity/ DC/voltage drop/
heat protection
Dimensions (LxHxW) 6 7/8" x 2 5/8" x 1 7/8"
(175mm x 66.5mm x 47mm)
Weight (1.2 lbs) 550g
Conditions of guarantee
All Focal loudspeakers are covered by guarantee drawn up by the official Focal distributor in your country. Your
distributor can provide all details concerning the conditions of guarantee. Guarantee cover extends at least to that
granted by the legal guarantee in force in the country where the original purchase invoice was issued.

15
amplifiCaTEUR impUlSE 4.320
Manuel d'installation
Sound”. Ce produit intègre le meilleur de la technologie Focal en matière d’amplification compacte classe D.
Pour obtenir les meilleurs résultats, nous vous recommandons de faire installer votre amplificateur IMPULSE
4.320 par votre revendeur Focal. Afin d’en exploiter l’ensemble des fonctionnalités et ainsi de profiter
pleinement de ses performances, nous vous conseillons de lire attentivement les instructions de ce livret, puis
de le conserver pour vous y référer ultérieurement. Tout problème dû au non-respect des règles d’utilisation
peut entraîner une invalidation de la garantie.
AVERTISSEMENT
Ce symbole désigne les instructions importantes. Le non-respect de ces instructions peut entrainer de
graves blessures ou des dommages matériels.
Contenu de l’emballage :
- 1 amplificateur IMPULSE 4.320
- 1 manuel d’utilisation
- 1 set d’accessoires
Accessoire disponible (vendu séparément) :
- 1 câble Plug and Play format ISO pour une connexion directe sur les autoradios compatibles
Pour validation de la garantie, merci de retourner,
dans les 10 jours suivant l’acte d’achat.
Version Française
AVERTISSEMENT
• N’activez aucune fonction susceptible de détourner votre attention lors de la conduite du véhicule. Les fonctions
ou réglages qui requièrent une attention prolongée ne doivent être exploités qu’à l’arrêt complet du véhicule.
Veillez à toujours stopper le véhicule dans un endroit sûr avant d’activer ces fonctions. Il y a risque de provoquer
un accident.
• Gardez le volume à faible niveau de façon à pouvoir entendre les bruits extérieurs lors de la conduite du
véhicule. Il y a risque de provoquer un accident.
• N’ouvrez pas votre amplificateur IMPULSE 4.320 et n’opérez pas de modifications sur le produit. Il y a risque
d’accident, d’incendie ou de choc électrique.
Votre produit Focal-JMlab a été conçu et fabriqué avec des matériaux et composants de haute qualité,
susceptibles d’être recyclés et réutilisés. Ce symbole signifie que les appareils électriques et électroniques,
lorsqu’ils sont arrivés en fin de vie, doivent être éliminés séparément des ordures ménagères. Veuillez
rapporter cet appareil à la déchetterie communale ou à un centre de recyclage. Vous contribuez ainsi à la
préservation de l’environnement.

16
amplifiCaTEUR impUlSE 4.320
Manuel d'installation
ATTENTION
• Utilisez votre amplificateur IMPULSE 4.320 sur des applications mobiles de 12 volts uniquement. Toute
utilisation autre que l’application désignée comporte un risque d’incendie, de choc électrique ou de blessure.
• Utilisez des fusibles d’ampérage approprié. Il y a risque d’incendie ou de décharge électrique.
• N’obstruez pas le radiateur de votre amplificateur IMPULSE 4.320. Une surchauffe interne peut se produire et
provoquer un incendie.
• Effectuez correctement les connexions. Vérifiez la section du câble et le type de câble. Il y a risque d’incendie,
de blessures et/ou d’endommagement de l’appareil.
• N’utilisez pas d’écrous ni de boulons du circuit de direction ou de freinage, des réservoirs, des ceintures ou
autres éléments de sécurité pour la connexion de la masse. L’utilisation de ces organes comme masse peut
désactiver le système de contrôle du véhicule et causer un incendie ou autre avarie.
• Gardez les petits objets susceptibles d’être ingérés, comme les boulons, accessoires ou les vis, hors de portée des
enfants. L’ingestion de tels objets peut entraîner de graves blessures. En cas d’ingestion, consultez un médecin.
• Avant d’entamer l’installation, déconnectez la borne négative de la batterie pour éviter tout risque de blessure,
d’incendie ou d’endommagement du matériel. (fig. 1)
fig. 1
ATTENTION
L’écoute prolongée à fort niveau, au-delà de 110 dB, peut détériorer durablement l’audition. Des écoutes, même
brèves, au-delà de 130 dB, peuvent provoquer des lésions auditives irrémédiables.
Interrompez toute utilisation en cas de problème. Le non-respect de cette précaution peut entrainer des blessures
ou endommager l’appareil. Si un dysfonctionnement persiste, retournez l’appareil auprès de votre revendeur Focal
en vue de sa réparation.
Utilisez les accessoires spécifiés et installez-les correctement. Utilisez uniquement les accessoires mentionnés
dans le manuel d’utilisation, ainsi que ceux qui sont fournis dans l’emballage. L’utilisation d’autres composants
peut causer des dommages internes au produit, ou son installation risque de ne pas être effectuée correctement.
Les pièces utilisées risquent de se desserrer et de provoquer des dommages ou une défaillance technique du
produit. Il y a risque d’accident, d’incendie ou de choc électrique.
N’installez pas le produit dans des zones fortement humides ou poussiéreuses. Evitez d’installer l’appareil dans
des zones du véhicule soumises à une forte humidité ou à une présence excessive de poussière. La pénétration
d’humidité ou de poussière à l’intérieur du produit risque de provoquer une défaillance.

17
amplifiCaTEUR impUlSE 4.320
Manuel d'installation
Installation de votre amplificateur IMPULSE 4.320
L’installation de ce produit requiert des compétences techniques et de l’expérience. En cas d’incertitude sur
l’aptitude à installer l’amplificateur, confiez cette tâche à un revendeur Focal afin de profiter pleinement de
l’ensemble des possibilités de votre amplificateur IMPULSE 4.320.
Câblage de votre amplificateur IMPULSE 4.320
Utilisez uniquement les départs de câbles préconisés dans le manuel d’utilisation et les accessoires fournis.
Utilisez éventuellement le câble ISO vendu séparément pour une mise en œuvre facilitée.
Le câble haut-parleur doit être UNIQUEMENT utilisez pour relier l’amplificateur aux haut-parleurs. La section des
câbles d’alimentation doit correspondre à celle mentionnée dans le tableau (paragraphe 3.1) et est fonction de
la puissance de l’amplificateur et de la longueur de câble nécessaire. Utilisez des câbles RCA à double ou triple
blindage pour éviter tout parasitage du signal bas niveau.
Durée de fonctionnement de votre amplificateur IMPULSE 4.320
Evitez de faire fonctionner l’amplificateur durant une longue période sans démarrer le véhicule. Ceci peut entraîner
la décharge prématurée de la batterie.
Ventilation
Il est impératif de ne pas couvrir la zone supérieure de votre amplificateur IMPULSE 4.320 afin de ne pas créer de
surchauffe.
Matériel requis pour effectuer l’installation (en dehors des accessoires fournis):
• 2 gaines de section adéquates (1 gaine pour le câble d’alimentation, 1 gaine pour le lot de câbles haut-parleurs,
REMOTE, modulation RCA)
• Multimètre (voltage/ampérage)
• Fer à souder + étain
• Pince à sertir
• Pince à dénuder
• Coupe-fils
• Clé de borne de batterie
• Perceuse à main et mèches assorties
• Gaines thermo-rétractables de diamètres appropriés aux différents câbles
• Câble d’alimentation de longueur et de section adéquates
• Câble d’allumage à distance (entrée REM de l’amplificateur) de longueur et de section adéquates
• Câble de masse de longueur et de section adéquates
• Porte-fusible et fusible adéquat
• Cosse de liaison à la borne positive (+) de la batterie
• Cosse de liaison au châssis du véhicule (-)
• Vis avec tête de vis de 6 mm au minimum et son écrou pour mise à la masse sur le châssis du véhicule
Installation
La section ci-dessous traite de points relatifs au véhicule dont il faut tenir compte pour l’installation de votre
amplificateur. Vous gagnerez du temps en planifiant à l’avance la disposition du système et du câblage.
Assurez-vous, durant cette étape préparatoire, que l’ensemble des réglages resteront accessibles une fois
l’installation terminée.

18
amplifiCaTEUR impUlSE 4.320
Manuel d'installation
Avant de commencer l’installation, merci de suivre scrupuleusement les règles suivantes :
1 - Apres lecture intégrale du manuel d’utilisation, assurez-vous d’avoir compris l’ensemble des instructions avant
d’installer votre amplificateur.
2 - Débranchez le fil négatif de la batterie avant de commencer l’installation (fig.1).
3 - Pour faciliter le montage, nous suggérons de dérouler tous les fils avant d’installer votre amplificateur.
4 - Acheminez l’ensemble des câbles RCA, haut-parleur et REM à l’écart des câbles d’alimentation afin d’éviter
tout parasitage du signal.
5 - Utilisez des connecteurs/raccords ou des soudures de qualité pour relier l’amplificateur afin d’assurer une
fiabilité d’installation et minimiser les pertes de signal ou de puissance.
6 – Vérifiez avant de réaliser quelque opération de ne pas couper ou percer le réservoir d’essence, les conduites de
carburant, de frein, hydrauliques ou de dépression, ainsi que le câblage électrique ou tout élément sécuritaire.
7 - Ne faites jamais passer de fil sous le véhicule. Il faut impérativement les installer à l’intérieur de celui-ci. Lors
du passage des câbles, vérifiez que ceux-ci ne gêneront pas la conduite du véhicule. Les câbles qui obstruent
ou dépassent à des endroits tels que le volant, les pédales (frein, accélérateur et embrayage, etc…), peuvent
s’avérer extrêmement dangereux.
8 - Evitez de faire passer des fils par-dessus ou à travers des bords tranchants. Tout fil acheminé à travers du métal
doit être protégé par des passe-fils. Acheminez les câbles à l’écart des pièces mobiles (rails d’un siège, …) et
des arêtes acérées ou pointues. Cela évitera ainsi de coincer ou d’endommager les câbles et d’engendrer un
court-circuit électrique.
9 - Protégez toujours la batterie et le circuit électrique de dommages potentiels à l’aide de fusibles. Installez un
porte-fusible et un fusible appropriés sur le câble d’alimentation 12 V positif (+) a moins de 40 cm de la borne
de la batterie. Idéalement, cette distance doit être la plus courte possible (fig.5).
10 - Préparez la masse du châssis en grattant toute trace de peinture sur la surface métallique afin d’assurer
une bonne mise à la masse. Les connexions de masse doivent être aussi courtes que possible et TOUJOURS
connectées à du métal soudé à la carrosserie ou au châssis du véhicule (fig. 2). Le point de masse généralement
retenu est celui assurant la liaison entre la borne négative de la batterie et le châssis du véhicule.
11 - NE MONTEZ JAMAIS ce produit dans le compartiment moteur du véhicule. Ceci entraînerait l’annulation de la
garantie.
I - Mise en place de votre amplificateur IMPULSE 4.320
Où installer votre amplificateur IMPULSE 4.320 ?
En raison de la puissance de l’amplificateur, une dissipation thermique est nécessaire au fonctionnement. Pour cette
raison, l’amplificateur doit être monté dans un endroit permettant une ventilation, tout spécialement sur le dessus.
Evitez tout encastrement ou recouvrement de l’amplificateur dans sa zone proche d’installation.
2 - Fixation de votre amplificateur IMPULSE 4.320
Positionnez votre amplificateur à l’emplacement souhaité et repérez-le.
Repérez les points de fixation dans votre support grâce aux pattes de fixation fournies.
Utilisez des vis de fixation adaptées à un vissage dans votre support.
3 – Câblage de votre amplificateur IMPULSE 4.320
AVERTISSEMENT
En cas de doute sur l’aptitude à installer l’amplificateur et câbler le système de façon adéquate, confiez
cette tâche a un revendeur/installateur Focal.

19
amplifiCaTEUR impUlSE 4.320
Manuel d'installation
ATTENTION
Evitez de faire passer les câbles d’alimentation près des câbles d’entrée bas niveau (LOW LEVEL INPUTS)
et haut niveau (HI LEVEL INPUTS), de l’antenne, des équipements et faisceaux sensibles. Les fils
d’alimentation transportent un courant élevé pouvant produire un parasitage du signal audio.
ATTENTION
Réduisez au maximum la longueur des câbles afin d’optimiser la qualité de l’installation et limiter ainsi
les pertes de signal.
ATTENTION
Avant de débuter la phase de connexion, retirez la borne négative (-) de la batterie du véhicule (fig. 1)
3.1 - Quelle section de câble d’alimentation choisir ?
Votre amplificateur IMPULSE 4.320 nécessite une alimentation d’ampérage approprié.
Les sections des câbles d’alimentation à utiliser dépendent de la distance de câblage à la batterie. Ils sont préconisés
dans le tableau suivant :
Longueur du câble en mètres jusqu’à la batterie
Longueur < 1 m < 3 m < 4 m
Section mm2Câble accessoire ISO
recommandé
3,3 mm2> 3,3 mm2
Section AWG 12 AWG < 12 AWG
Le respect de ces règles de câblage est indispensable à l’aspect sécuritaire de votre installation électrique, il est
également important pour maintenir les performances maximales de votre amplificateur IMPULSE 4.320.
3.2 – Câblage des signaux d’entrée et sortie sur votre amplificateur IMPULSE 4.320
3.2.1 – Votre autoradio est équipé de sorties RCA
Acheminez ensemble les câbles de modulation (RCA), les câbles haut-parleurs, le câble REM en les isolant des
autres accessoires automobiles de forte puissance, particulièrement les moteurs électriques (essuie-glace, ...).
Conservez toute la longueur des câbles, elle sera ajustée plus tard.
3.2.2 – Votre autoradio est uniquement équipé de sorties amplifiées (sorties haut-parleurs)
Acheminez ensemble les câbles de modulation en provenance des sorties de l’autoradio, les câbles haut-parleur
en les isolant des autres accessoires automobiles de forte puissance, particulièrement les moteurs électriques
(essuie-glace, ...). Conservez toute la longueur des câbles, elle sera ajustée plus tard.
3.3 – Câblage de l’alimentation de votre amplificateur IMPULSE 4.320
3.3.1 – Acheminez le câble d’alimentation positif (+) en prenant soin de le faire passer à l’opposé des câbles
précédemment tirés pour éviter tout parasitage. NE CONNECTEZ PAS LE CABLE POUR L’INSTANT.

20
amplifiCaTEUR impUlSE 4.320
Manuel d'installation
3.3.2 – Munissez-vous du câble d’alimentation négatif (-). Ce câble doit être le plus court possible et ne doit
idéalement pas dépasser 1 mètre afin d’assurer une parfaite liaison entre l’amplificateur et le châssis du véhicule.
Le câble et sa section doivent être conformes au tableau mentionné en 3.1. Trouver un point de masse adéquat,
puis poncez-le pour enlever toute trace de peinture ou autre verni et ainsi optimiser la qualité du contact. Percez la
tôle préalablement poncée au diamètre correspondant à la vis choisie en s’assurant qu’aucun passage de câbles
réservoir ou autre organe sensible du véhicule ne soit à proximité. Soudez et isolez (grâce à de la gaine thermo-ré-
tractable) le câble de masse sur le départ de câble fourni vers votre amplificateur IMPULSE 4.320 (fig. 2).
3.4 – Connexion des signaux d’entrée sur votre amplificateur IMPULSE 4.320
La phase de connexion des câbles d’entrée/sortie peut débuter.
3.4.1 – Votre autoradio est équipé de sorties RCA
Connectez les RCA au câble d’adaptation RCA fourni (fig. 3) en respectant les polarités (INPUT Left = noir ou blanc,
INPUT Right = rouge) et répartition (F=FRONT=AVANT, R=REAR=ARRIERE). Connectez l’autre extrémité au panneau
de connexion INPUTS de l’amplificateur.
fig. 2
fig. 3
Positionnez le sélecteur d’entrées ( INPUTS LEVEL) sur LOW (faible niveau). (fig. 4)
fig. 4
Table of contents
Languages:
Other Focal Car Amplifier manuals

Focal
Focal FP Dual Direct User manual

Focal
Focal Power Symmetric High-Cap User manual

Focal
Focal FPS 4160 User manual

Focal
Focal Power Symmetric User manual

Focal
Focal FPS 1500 User manual

Focal
Focal FPP1000 User manual

Focal
Focal POWER SYMMETRIC AMPLIFIERS User manual

Focal
Focal FP Dual Monitor User manual

Focal
Focal FP Dual Monitor User manual

Focal
Focal FPS 2300RX User manual