FONESTAR MA-125 User manual

MA-125, MA-245
PA AMPLIFIER
INSTRUCTION MANUAL
160906_MA-125_MA-245_MANUAL_(EN)_Maquetación 1 28/11/16 18:22 Página 1

We take this opportunity to thank you for buying this product.
We recommend you read the instruction manual before switching on the machine and follow the instructions
that are given. Keep the manual for future reference.
SECU ITY AND THE ENVI ONMENT
ELECTR CAL SECUR TY
Check that the current in the mains connection where the machine is to be installed corresponds to the
power supply of the machine.
To avoid damaging the equipment, electrical shocks, fire or physical injury when you connect or disconnect
the equipment from the power supply, pull the plug firmly out of the mains socket holding the plug, never the
cable.
Always do this with dry hands.
Keep the power supply cable far from sources of heat. Do not put heavy objects on top of it or change it.
Clean dust and dirt off the power supply cable regularly.
Do not open the machine; you could get an electric shock.
CAUT ON
While installing the machine, make sure it is switched off and unplugged.
Do not open the machine. Touching the internal parts is dangerous and you could receive an electric shock.
The machine must not be splashed or dripped on. Never place recipients with liquid inside on the machine.
Do not place anything inside the machine.
LOCAT ON
Place the equipment on a horizontal surface with enough space around it to allow ventilation.
Avoid direct sunlight, heat sources and excessive dust.
Do not place the machine near magnetic fields or static electricity.
Do not use surfaces which vibrate or receive impact.
Do not pile machines on top of one another.
VENT LAT ON
Never block or cover the ventilation slits on the machine.
Do not expose it to direct sunlight or place it near sources of heat.
PER ODS OF NACT V TY
When the machine is not going to be used for a long period of time, disconnect it from the mains.
f you are using an adapter, take into account that it will continue using electricity even if the machine is
switched off. f it is not going to be used for a long period of time, disconnect it from the mains.
THE ENV RONMENT
To save energy, switch the machine off when you are not going to use it for a long time. The machine could
contain substances that are harmful to the environment or human health. To minimize the effect of these
substances the machine must be correctly managed and recycled when you decide to dispose of it.
When you dispose of it remember: it cannot be thrown into a conventional rubbish bin.
f it contains or uses batteries, these must be disposed of separately.
The machine (without batteries) must be disposed of correctly. Put it in a container specially intended for the
collection of electronic and electrical appliances, at the dump or hand it over to the dealer when you purchase
similar equipment, so that the dealer can dispose of it correctly (at no added cost).
- 2-
EN
160906_MA-125_MA-245_MANUAL_(EN)_Maquetación 1 28/11/16 18:22 Página 2

SIGNIFICANCE OF THE SYMBOLS ON THE MACHINE*
The symbol formed by the expression “Class 1 laser product” written in a rectangle
indicates that visible or invisible laser radiation could be produced. Avoid direct expose to
the laser.
The symbol formed by a ray of lightening inside a triangle shows that the machine has
connection terminals or a circuit with areas with a current which could cause an electric
shock, even in normal working conditions.
The symbol formed by an exclamation mark in a triangle shows that the instruction manual
must be referred to for information on how the machine works and its use.
The symbol formed by one square inside another square shows that the machine has
double electrical insulation.
The European Community symbol shows that the machine complies with the current
European Union legislation, as well as its transposition to local legislation.
The symbol of a rubbish bin crossed out and over a horizontal line shows that when the
product is disposed of it must be done properly, placing it in a special selective electronic
and electrical equipment container or through a dealer when purchasing a similar product,
at no additional cost. t also shows that the machine was put on the market after 13th
August 2005 (European Community Directive 2002/96/CE of Electrical and Electronic
recycling, and its Spanish equivalent R.D.208/2005).
n accordance with what is set out in the aforementioned decree, FONESTAR is registered
in the RAEE (Registro de Aparatos Eléctricos y Electrónicos) in a special section RE
(Registro de establecimientos ndustriales), with the entry number 001851.
* t is possible that some of these symbols do not appear on the machine.
EXEMPTION OF LIABILITY
The characteristics of the equipment and the content of the manual can change without forewarning.
FONESTA , S.A. does not assume responsibilities regarding the inappropriate use of the equipment or the
information supplied in this instruction manual, and specifically disclaims any implied liability for marketability
or fitness for any other use.
All rights reserved by FONESTA , S.A.
- 3-
EN
160906_MA-125_MA-245_MANUAL_(EN)_Maquetación 1 28/11/16 18:22 Página 3

EN
- 4-
DESC IPTION
- PA amplifier.
- With phantom power supply and priority.
CONT OLS AND FUNCTIONS
F ONT PANEL
1.- INPUT 1-4 and AUX: controls which regulate the volume of inputs 1 to 4 and the aux input.
2.- BASS: reinforces or attenuates bass frequencies ±10 dB.
3.- T EBLE: reinforces or attenuates treble frequencies ±10 dB.
4.- MASTE : control which regulates the general output volume of all the inputs.
5.- OUTPUT LEVEL: LED indicators for the output signal level. t regulates the individual volume controls
of the inputs or the general (MASTER) output volume control so that the level does not exceed the green
LED indicators. The red LED indicators indicate saturation or a distorted signal which could damage the
loudspeakers or the amplifier.
6.- POWE : amplifier on/off switch.
EA PANEL
1.- Ventilation grille: to ventilate the output stage.
2.- GND. Earth: screw to earth the amplifier to be used in the case of the mains connection not having one
incorporated.
3.- 115V/230V: power supply voltage selector.
4.- AC socket: for the AC power supply cable connection.
5.- AMP IN/P E OUT: the connection bridge between the two RCA connectors communicates the output
signal from the preamplifier (PRE OUT) with the amplifier input (AMP N).
6.- LINE OUT: aux line output. Signal output for recording, mixer, amplifier etc., 2 x RCA connectors.
7.- AUX: aux input. Signal source input, allows connection of audio sources via RCA connectors.
160906_MA-125_MA-245_MANUAL_(EN)_Maquetación 1 28/11/16 18:22 Página 4

8.- LINE/PHANTOM 24 V/MIC: input and 24 V phantom sensitivity switches. These switches have 3 positions:
LINE: in this position, high level audio sources can be connected to inputs 1 to 4: preamplified
microphones, CDs, tapes, tuners, etc.
MIC: in this position, 30-600 Ω low impedance dynamic microphones can be connected to inputs 1 to 4.
PHANTOM 24 V: in this position, electret condenser microphones which require 24 V phantom power
supply can be connected to inputs 1 to 4.
Use this switch with the volume at its minimum to avoid noise.
9.- MUTE/SEN: control which allows priority to be activated/deactivated in the NPUT 1 and TEL inputs.
Turn the control clockwise to its maximum and the rest of the inputs will automatically attenuate when
a signal is detected in the NPUT 1 or TEL inputs. Turn it anti-clockwise and the priority function will be
at its minimum.
Note: the amplifier is supplied with priority deactivated. n order to activate this function you must turn
the MUTE/SENS control clockwise to its maximum (maximum priority).
10.- TEL. LEVEL: TEL. NPUT volume control. This allows the volume of the telephone switchboard which
is connected to the TEL. NPUT terminals to be adjusted. Turning the control clockwise increases the
volume and anti-clockwise decreases it.
11.- TEL. INPUT: telephone input terminals. Allow connection to a telephone switchboard to page from the
switchboard with priority over the rest of the inputs. Consult the characteristics of the switchboard in
order to adjust the input level of the amplifier. The signal level can be adjusted with the TEL. LEVEL
control on the rear panel.
Note: the amplifier is supplied with priority deactivated. n order to activate this function you must turn
the MUTE/SENS control clockwise to its maximum (maximum priority).
12.- Aux loudspeaker output terminals 1 W 8 Ω - 600 Ω (Monitor): output terminals which permit the
connection of an external loudspeaker as a monitor. t has a 1 W internal amplifier. t only monitors the
AUX N input, controlled with the AUX volume, and adjustable level with the LEVEL/MOH control on the
rear panel.
13.- LEVEL/MOH: monitor output volume control. Turning the knob in a clockwise direction, increases the
the volume and in an anti-clockwise direction, decreases it.
14.- INPUT 1 to 4: microphone/line inputs which use a combined XLR and 6.3 mm jack connector, accepting
balanced and unbalanced microphone signals of 30-600 Ω and balanced electret condenser
microphones which require 24 V phantom power supply in pins 2 and 3 of the XLR connector. They
accept high level line signals, balanced or unbalanced, from mixers, CDs, tapes, tuners, etc.
Select the appropriate position with the switch, being careful to set the volume controls at their minimum
to avoid noise.
The microphone 1 input has the priority function, which cancels all other inputs to give priority to paging,
emergencies, etc. The amplifier is supplied with priority deactivated. n order to activate this function you
must turn the MUTE/SENS control, on the rear panel of the device, in a clockwise direction to its
maximum (maximum priority).
CAUTION: when connecting or disconnecting an unbalanced microphone it is necessary that the switch
is in the M C position. f the switch is in the PHANTOM 24 V position it could damage the microphones.
When using microphones that do not require phantom power supply, make sure that the switch is in the
M C position, as the voltage present in pins 2 and 3 of the XLR connector could damage the
microphones. f in doubt, please consult your supplier or the FONESTAR technical service.
15.- OUTPUT: loudspeaker output. For the connection of loudspeakers in low impedance 4 Ω and in high
impedance 100/70/25 V lines. Connect the line of loudspeakers between the COM terminal and the
required impedance or V line.
16.- DC Power Input: 24 V DC power supply terminals. For the amplifier to work with 24 V power supply,
batteries, emergency power supply systems, etc. Make the connection with 2.5 mm² section cable to
the – negative and the + positive terminals.
Note: when the amplifier is used with 24 V DC, the power is reduced by approximately 20%.
EN
- 5-
160906_MA-125_MA-245_MANUAL_(EN)_Maquetación 1 28/11/16 18:22 Página 5

EN
- 6-
CONNECTION
Make the connections with the amplifier and all the components of the audio system switched off and
disconnected from the power supply.
Firstly, connect the audio sources to the inputs. Connect the loudspeakers to the loudspeaker outputs. Use
the 4 Ω low impedance output or the 100, 70 or 25 V high impedance lines, according to the type of
loudspeakers you are going to connect. Do not use both types of output at the same time.
f you use the low impedance output, you must connect the loudspeakers in a series/parallel circuit so that
the load impedance of the loudspeakers is the same as the amplifier output impedance and that the power
supplied by the amplifier does not exceed that withstood by the loudspeakers.
f you use a 100, 70, or 25 V high impedance line output, you must connect all the loudspeakers in parallel
and the sum of the power of all the loudspeakers must not exceed the power supplied by the amplifier.
Once the connections have been made according to your needs, connect the system to the mains and turn
it on. After use, do not forget to switch the device off and disconnect it from the mains.
160906_MA-125_MA-245_MANUAL_(EN)_Maquetación 1 28/11/16 18:22 Página 6

TECHNICAL SPECIFICATIONS
MA-125 MA-245
CHA ACTE ISTICS PA amplifier.
Phantom power supply.
Priority paging.
POWE 180 W maximum, 120 W RMS 360 W maximum, 240 W RMS
ESPONSE 80-16 000 Hz ±3 dB
DISTO TION Harmonic: < 1 % at 1 kHz
INPUTS 4 balanced mics./lines, combo (XLR and 6.3 mm jack) 600 Ω 2 mV and
47,000 Ω 150 mV, switchable
1 aux, 2 x RCA, 47,000 Ω 300 mV
1 amp in, RCA 10,000 Ω 1 V
1 tel. input, screw terminal blocks 600 Ω 100 mV
OUTPUTS 1 line out, 2 x RCA 47,000 Ω 1 V
1 pre out, RCA 600 Ω 1 V
1 monitor, screw terminal blocks 600 Ω 775 mV and 1 W 8 Ω (aux input)
CONT OLS Tone:
Bass: ±10 dB
Treble: ±10 dB
Volume: inputs 1 to 4, aux and general volume
PHANTOM 24 V in mics 1 to 4, selectable
P IO ITY Tel. input and mic. 1 depending on signal level, selectable
IMPEDANCE 4 Ω and 100, 70 and 25 V lines, screw terminals
POWE SUPPLY 230/115 V AC, 290 W and 24 V
DC, 161 W
230/115 V AC, 600 W and 24 DC,
312 W
DIMENSIONS 420 x 89 x 300 mm depth. 2 U 19” rack
OPTIONAL MA-2N: mounts for assembly in 19” rack
- 7-
EN
- 7-
160906_MA-125_MA-245_MANUAL_(EN)_Maquetación 1 28/11/16 18:22 Página 7

BLOCK DIAG AM
- 8-
EN
160906_MA-125_MA-245_MANUAL_(EN)_Maquetación 1 28/11/16 18:22 Página 8

- 9-
ES
160906_MA-125_MA-245_MANUAL_(EN)_Maquetación 1 28/11/16 18:22 Página 9

- 10 -
EN
160906_MA-125_MA-245_MANUAL_(EN)_Maquetación 1 28/11/16 18:22 Página 10

- 11 -
ES
EN
DECLA ATION OF CONFO MITY
FONESTA SISTEMAS S.A.
Polígono de Trascueto s/n
39600 Revilla de Camargo, Cantabria (Spain)
Declares, under its responsibility, that the following equipment:
Description: PA amplifier
Brand: FONESTAR
Model: MA-125, MA-245
complies with the European Community directivas 2004/108/EC on Electromagnetic Compatibility,
2006/95/EC on Low Voltage and 2011/65/EU on the restriction on the use of certain dangerous
substances in electrical and electronic appliances (RoHS).
Santander, 28th June 2016
Juan Vallejo
Technical Engineer, Sales Department
WA ANTY
This product has been tested and has passed the corresponding quality control prior to being put on the market.
FONESTA guarantees the suitability of the product for its specified use during a period of 2 years from the delivery
date and commits itself to repair or substitute the goods as expressed in the Spanish law ‘La Ley General para la
Defensa de los Consumidores y Usuarios, Real Decreto Legislativo 1/2007 16 Noviembre.
The lack of conformity in the first six months after purchase, due to a manufacturing defect, will be rectified with
no more than showing the proof of purchase. After six months FONESTA reserves the right to demand proof of
the product being sold with that problem.
This warranty does not include damage produced by: inappropriate use or negligence, accidents, worn out parts
due to use, breakages, burns, spilt liquids or other substances, excessive humidity, battery deterioration and internal
manipulation of the device, the software or its components by unauthorized persons, and in general any use that
is unrelated to the nature and purpose of the product.
f any service is needed during the warranty period because of lack of conformity, please contact the business or
distributor where the product was purchased in no more than 2 months after being conscious of the problem. t is
only necessary to contact FONESTA if it is impossible or imposes an undue burden for them to solve it.
To benefit from this warranty it is necessary to show the proof of purchase with the date clearly visible, with no
corrections or crossing out.
This document adds information, and never decreases the consumers’ rights, which in all cases are protected by
the Spanish law ‘La Ley General para la Defensa de los Consumidores y Usuarios, Real Decreto Legislativo 1/2007
16 Noviembre’.
FONESTA is a member of ECOEMBALAJES ESPAÑA, S.A. “ECOEMBES”, with number 03497 and all our products
carry the symbol, backed by our membership and subscription to the above mentioned organization with the recycling
and subsequent management of our packaging.
FONESTAR, S.A. - N F: A28780443 - Polígono Trascueto - 39600 Revilla de Camargo, Cantabria (SPA N)
www.fonestar.com
160906_MA-125_MA-245_MANUAL_(EN)_Maquetación 1 28/11/16 18:22 Página 11

www.fonestar.com
160906_MA-125_MA-245_MANUAL_(EN)_Maquetación 1 28/11/16 18:22 Página 12