Fontana Showers FS1320D User manual

Plumbers Tape Tape Measure Adjustable Wrench
Screwdriver
Drill
Hex Wrench
Level
Pencil or Marker
Thread Sealant
*not included
POSSIBLE TOOLS REQUIRED*
FONTANASHOWERS BRUSHED NICKEL CEILING
MOUNT RAINFALL DUAL SHOWER HEAD SET WITH
HANDSHOWER INSTALLATION INSTRUCTIONS
Product code: FS1320D
1
Please read installation instructions below. All plumbing should be
installed in accordance with applicable building codes and regulations.
Unpack and inspect the items for any shipping damages. If you find
damages, do not install.
All products must be installed by a professional and certified plumber
otherwise warranty may be voided.
PRIOR TO INSTALLATION
FontanaShowers©
FontanaShowers©
FontanaShowers
FontanaShowers Customer Service: 800-684-4489
fontanashowers.com

FontanaShowers©
FontanaShowers©
FontanaShowers
FontanaShowers Customer Service: 800-684-4489
fontanashowers.com
2
Shower Head Installations Instruction
Parts:
Step 3:
Step 1:
D
C
E
F F
Mark the 4 drilling positions then
use the Ø6mm drill to drill holes on the
wall according to the marked hole
position.
Inset the plug(D) into the hole, hold the fix base (C) use the tapping screw (D) through
fix base(C) holes, tighten the tapping screw (D) tighten the top shower fixed bar(E) and
the inlet hose (F) with the fix base (C)

Fixed the top shower with the top shower fixed bar (E) , then connect with the inlet hose
(F) . 2 Inlets for Rainshower are provided in big shower heads so the water disperses
equally throughout the showerhead.
The installation is completed.
Note: The LED lights are powered by water flow, and will be activated once the water is
turned on.
E
F
Step 5:
Step 6:
FontanaShowers©
FontanaShowers©
FontanaShowers
FontanaShowers Customer Service: 800-684-4489
fontanashowers.com
3

Min 13±2mm
25mm
Trim Ring
Arm
Wall
Filter Washer
Ball Joint
Slide chrome trim ring onto the appropriate
end of the arm. Ensure that a minimum of
13±2mm of 1/2” connection thread protrudes
past the finished wall. Simply screw the arm
onto the connection. Correct water proofing
must be applied.
Position the arm vertically and push trim
ring into place. Use wrenching flats to
tighten.
DO NOT USE ARM TO LEVER
Remove the protective cap from the
showerhead ball joint and screw the unit onto
the overhead arm ensuring the filter washer is
in place.
Shower Head Installations Instruction
Step 1: Step 2:
Step 3: Step 4:
FontanaShowers©
FontanaShowers©
FontanaShowers
FontanaShowers Customer Service: 800-684-4489
fontanashowers.com
4

FontanaShowers©
FontanaShowers©
FontanaShowers
FontanaShowers Customer Service: 800-684-4489
fontanashowers.com
5
Mixer Installations Instructions
Step 2
Step 1
Step 3 ( Connection)
Hot water
Cold water
Rough-in Body
Anchor
Positioning
Bar
Tapping Screw 1
Tapping Screw 2
Plate
Cover
Button
Screw 1
Diverter
Handle
Temp.
Handle
On/Off
Handle
Hex Wrench
Hot Water In Cold Water In
Function 1
Function 2
Function 3

FontanaShowers©
FontanaShowers©
FontanaShowers
FontanaShowers Customer Service: 800-684-4489
fontanashowers.com
6
Step 1 Step 2
Step 3
Hand-Held Shower Installations Instructions
Step 5 Step 6
Step 4

FontanaShowers©
FontanaShowers©
FontanaShowers
FontanaShowers Customer Service: 800-684-4489
fontanashowers.com
7
Step 7 Step 8
Step 9
Step 11 Step 12
Step 10

8
FontanaShowers©
FontanaShowers©
FontanaShowers
FontanaShowers Customer Service: 800-684-4489
fontanashowers.com
Step 13 Step 14
Step 15: (Hand Shower Elbow Installation)
Step 17 Step 18
Step 16

9
FontanaShowers©
FontanaShowers©
FontanaShowers
FontanaShowers Customer Service: 800-684-4489
fontanashowers.com
Step 19 Step 20
Step 21 Step 22
Open The Closed Cover Of The Shower Holder And Take Out The Screws.
Drill Two Holes Size 0.2" (6mm) On The Wall According To The Hole Position Of The Shower Holder
Use A Hammer To Break 2 Plastic Wall Plug Into Two Holes. Tighten The Screws With The Plastic Wall Plug
And Locking With The Shower Holder.
Then Install The Closed Cover
Connect The Shower Hose With The Water Outlet Connection Part And Hand Shower. Plug The Hand
Shower In The Shower Holder.

10
FontanaShowers©
FontanaShowers©
FontanaShowers
FontanaShowers Customer Service: 800-684-4489
fontanashowers.com
Acid
Care & Cleaning
General Information
1. The product can be cleaned with warm water, a mild soap and a clean soft cloth.
2. Clean progressively and gently.
3. It is not required to use any abrasive cleaning pads, wire wool or cloths to clean the
product.
4. Avoid a vigorous cleaning action, as this could contribute to denaturing and dulling
5. Abrasive or strong cleaning products containing ammonia, bleaches, alcohol, dyes,
acids (hydrochloric, formic, phosphorus, chlorine or acetic) will be not be affected.
All products manufactured and supplied by Fontana are safe and comply to legislative
requirements. Providing they are installed correctly and receive regular maintenance in
accordance with these instructions your user experience will not be affected
6. If using a spray cleaner, apply the cleaning agent onto a soft cloth, never directly
spray onto the product as the cleaner may enter gaps and openings and cause
damage. Do not allow the cleaner to remain on the product for a period of time. After
cleaning, rinse thoroughly with clean water.