Bristan VAL2 BIB C CD Wiring diagram

56
2
4
3
1
Pack Contents
Installation Instructions
& User Guide
Prior to Installation
Installation
Please leave these instructions
with the end user
Product Code: VAL2 BIB C CD (D1)
All products manufactured and supplied by Bristan are safe provided
they are installed, used correctly and receive regular maintenance in
accordance with these instructions.
This product has been tested to the Water Regulations Advisory
Scheme (WRAS) and satisfies the requirements of the Water Supply
(Water Fittings) Regulations 1999 and current bylaws.
For full Installation Requirements & Notes (IRN) please visit
wras.co.uk/directory.
We recommend isolation valves to be fitted to the inlet water
supplies to ensure ease of future maintenance.
Before installing these taps the water supply must be
thoroughly flushed in order to remove any swarf, solder etc.
This product must not be modified in any way as this will
invalidate the guarantee.
If power tools are used do not forget to:
- Wear eye protection
- Unplug equipment after use
If in doubt, contact a registered plumber or your Local Water
Authority or the Secretary of the Institute of Plumbing, address
as follows:-
The Institute of Plumbing,
64 Station Lane,
Hornchurch,
Essex,
RM12 6NB, Tel: [phone]
Feed the tap bodies
through the wall.
Screw the shrouds on
to the tap bodies.
Secure the taps by using washers and metal
backnuts behind the wall (not supplied).
Connect the hot and cold water
supplies to the threaded tails.
We recommend using elbows
(not supplied).
Turn on water supply.
REMEMBER
Hot on the left,
cold on the
right!
To replace any spare parts
for your tap, why not
scan the QR Code or
visit www.bristan.com
and search for your product.
Spare Parts
x2
x2
1.0
5.0
Pressure
BAR
0.2
4.0
2.0 3.0
Pressure
BAR
1.0
5.0
0.2
4.0
2.0 3.0
Specifications
Maximum Static Pressure: 10.0 bar
Inlet Water Temperature
Inlet Connections
Min: 0.2 bar Max: 5.0 bar
Dynamic Water Pressure
Tools You’ll Need
Flat Head
Screwdriver
Long-Nosed
Pliers
1/2” BSP
60°C
65°C
60-65°C Recommended
Identify the required position of the taps and
prepare the water supply pipes.
Mark and drill holes. Finish the wall surface.
Create the rear
access point
in the back of
the wall cavity.
IMPORTANT
Turn on water
supply for a few
minutes and check
all joints and
connections for
any leaks.
IMPORTANT
Bib taps can also
be fitted to X US C
and BTE C.
Please refer to
those instructions
if being used.
Crosshead
Screwdriver
Adjustable
Spanner
Pipe Cutter Pencil Safety
Goggles
Drill

2
1
Using long-
nosed pliers,
unscrew
gently to
remove the
outlet.
Check for damage.
Soak using a suitable
solution to de-scale.
Screw back into the tap
body to replace the outlet.
IMPORTANT
Isolate the
water supply
before
starting!
2
3
1
4
Prise o the caps
and indices. Undo the
screws to remove
the handles.
Unscrew the valve
using an adjustable
spanner.
Check any seals
and O-rings for
damage. Replace
valve if necessary.
Place valves
in a suitable
solution and
soak until
fully de-scaled.
Reverse the steps to replace the
valves and handles.
Maintenance - Valve Cleaning
123
At Bristan, we want to make things as easy as possible for our customers.
That’s why we oer solid guarantees on all our products, eective from the date of purchase,
to give you peace of mind.
To start your free guarantee simply scan the QR code and register your product.
Alternatively visit www.bristan.com/register to register your product via a computer.
For full guarantee terms and conditions visit www.bristan.com/guarantees.
Operation General Cleaning
Troubleshooting
Notes
Symptom Cause Remedy
No flow or
low flow
rate
Partially closed isolation valve. Open isolation valve.
Instantaneous water heater cycles on
and o as flow rate or pressure is too
low.
Increase water flow rate or pressure through system.
Head of water is below the
minimum distance required.
Refer to specification for minimum distance required.
Hot or cold water being drawn o
elsewhere causing pressure changes or
instantaneous boiler temperature
changes.
Do not use other water outlets when using the taps.
Airlock or partial blockage in the supply
pipework.
Flush through pipework to ensure removal of debris
and any airlocks.
Water
dripping
from taps
This is normal for a short time after using
the taps.
This is caused by residual water tension, the build up
of water in the tap body.
If water continues to drip,
possibly due to the ceramic disc valves
Remove valves and clean, refer to 'Maintenance'
section before starting any maintenance.
Taps do not
turn on
Closed isolation valve. Open isolation valve.
Mains water supply turned o. Turn on mains water supply.
Please use this space for any notes
you or your installer may have
regarding the installation/plumbing
of this product.
Bristan products are made from premium
materials, with hand polishing and
electroplated finishes.
Your taps or shower should be regularly
cleaned with warm water, a mild pH-neutral
liquid soap, and polished with a soft cloth.
Any residues from soap, toothpaste,
shampoos and shower gels can cause
blemishes if not rinsed o straight after use.
Household bleaches and cleaners contain
harsh chemicals and may damage the surface
finish. Avoid using abrasive cloths, scouring
pads, scrub sponges, steel wool
or anything similar.
Some surfaces such as nickel and pewter
may be aected by the dye found in some
cloths, so it is also important to avoid
hanging cloths on spouts.
O
O
On
Hot
Cold
On
IMPORTANT
Isolate the
water supply
before
starting!
Maintenance - Clean/Replace Outlet
Love Your Chrome Bristan oers an eective chrome-friendly cleaning kit
for use with your taps and showers. Scan the QR Code
or search for ‘CLEAN KIT01’ on www.bristan.com.