Fontana Showers FS1048 User manual

Plumbers Tape Tape Measure Adjustable Wrench
Screwdriver
Drill
Hex Wrench
Level
Pencil or Marker
Thread Sealant
*not included
POSSIBLE TOOLS REQUIRED*
Please read installation instructions below. All plumbing should be
installed in accordance with applicable building codes and regulations.
Unpack and inspect the items for any shipping damages. If you find
damages, do not install.
All products must be installed by a professional and certified plumber
otherwise warranty may be voided.
PRIOR TO INSTALLATION
BRAVAT BRUSHED GOLD SHOWER SET WITH VALVE MIXER
3-WAY CONCEALED WALL MOUNTED INSTALLATION
INSTRUCTIONS
Product code: FS1048
FontanaShowers©
FontanaShowers©
FontanaShowers
FontanaShowers Customer Service: 800-684-4489
fontanashowers.com
1

Wall Mount Shower Installations Instructions
Step 1: Step 2:
Step 3: Step 4:
Step 5: Step 6:
FontanaShowers©
FontanaShowers©
FontanaShowers
FontanaShowers Customer Service: 800-684-4489
fontanashowers.com
2

1. Remove the old shower head by using the channel lock pliers or monkey wrench. Be
sure to turn the pliers counter-clockwise to loosen the old shower head. (tip: right is tight,
left is loose.)
2. Remove the shower arm by turning it by hand counter-clockwise. Make sure you
remember to apply putty or tape to the new arm. (tip: using teflon tape is less messy)
3. Apply teflon tape to the threading of the shower arm by wrapping it around the threads,
go all the way around 3 or 4 times depending on the quality of the teflon tape.
4. Install the new shower arm by going clockwise by hand until it is tight, then put painters
tape around the arm and tighten the arm with the channel lock or monkey wrench.
5. Place teflon tape around the threads on the shower head and then place the shower
head onto the shower arm by turning the shower head clockwise after the shower arm is
already in the wall.t
Step 7: Step 8:
Step 9 (Note):
Product shown is only for installation display purpose
FontanaShowers©
FontanaShowers©
FontanaShowers
FontanaShowers Customer Service: 800-684-4489
fontanashowers.com
3
3

Apply Teflon Tape
Appropriate
fitting
To fit
flush
Can be cut
to length
Hand Shower Installations Instruction
Hand Shower Outlet Installation
• Complete the outlet pipework ensuring it ends in an appropriate 15mm x 1/2" BSP female thread elbow.
Note: This fitting is not supplied as variations in installations require the selection of a suitable solder or
compression fitting.
• Install the 'Wall Outlet', thread long male 1/2" BSP into the appropriate female fitting using PTFE tape to
give a watertight joint.
Note: The thread can be cut to size if required. Make sure that all debris is removed from the connector and
the section that has been cut is dressed correctly, before installation.
Step 1: Step 2:
Step 3: Step 4:
FontanaShowers©
FontanaShowers©
FontanaShowers
FontanaShowers Customer Service: 800-684-4489
fontanashowers.com
4

Body Jets Spray Installations Instruction
Step 1: Attach the escutcheon to the body
spray.
G1/2
Step 2: Apply teflon tape to threaded tail pipe
of the body spray
Step 3: Press the escutcheon against the
finished wall
Step 4: Screw the Body spray tightly into the
female of water Supply
Pressure Balancing Loop:
•If installing bodysprays in a bank of 3 or
fewer, a pressure balancing loop is not
necessary.
•If installing bodysprays in a bank of 4 or
greater, a pressure balancing loop must be
used to keep the pressure even between the
bodysprays.
FontanaShowers©
FontanaShowers©
FontanaShowers
FontanaShowers Customer Service: 800-684-4489
fontanashowers.com
5

Mixer Installations Instructions
Finished Wall
Floor
69-81 mm
Hot Cold
Close
Open
Hot Cold
90°
25°
Hot Water
Inlet
Cold Water
Inlet
Mixer
Body Jet
Shower
Hand
Shower
Step 2Step 1
Step 3 Step 4
Step 5 Connections
FontanaShowers©
FontanaShowers©
FontanaShowers
FontanaShowers Customer Service: 800-684-4489
fontanashowers.com
6
8
12

1. The product can be cleaned with warm water, a mild soap and a clean soft cloth.
2. Clean progressively and gently.
3. It is not required to use any abrasive cleaning pads, wire wool or cloths to clean the
product.
4. Avoid a vigorous cleaning action, as this could contribute to denaturing and dulling
5.Abrasive or strong cleaning products containing ammonia, bleaches, alcohol, dyes,
acids (hydrochloric, formic, phosphorus, chlorine or acetic) will be not be affected.
6. If using a spray cleaner, apply the cleaning agent onto a soft cloth, never directly spray
onto the product as the cleaner may enter gaps and openings and cause damage. Do
not allow the cleaner to remain on the product for a period of time. After cleaning, rinse
thoroughly with clean water.
Acid
General Information
Care & Cleaning
FontanaShowers©
FontanaShowers©
FontanaShowers
FontanaShowers Customer Service: 800-684-4489
fontanashowers.com
All products manufactured and supplied by Fontana are safe and comply to legislative
requirements. Providing they are installed correctly and receive regular maintenance in
accordance with these instructions your user experience will not be affected.
7