Fontana Showers FONTANA CARPI FS15045 User manual

Plumbers Tape Tape Measure Adjustable Wrench
Screwdriver
Drill
Hex Wrench
Level
Pencil or Marker
Thread Sealant
*not included
POSSIBLE TOOLS REQUIRED*
Before you begin, please read the installation instructions below. Observe
all local building and safety codes.
Unpack and inspect the items for any shipping damages. If you find
damages, do not install.
Please note all products must be installed by a professional and certified
plumber otherwise warranty might be voided.
BEFORE YOU BEGIN
FONTANA CARPI 20" LED INTELLIGENT
THERMOSTATIC DIGITAL DISPLAY TOUCH PANEL
WALL MOUNTED SHOWER SYSTEM INSTALLATION
INSTRUCTIONS
Product code: FS15045
1
FontanaShowers©
FontanaShowers©
FontanaShowers
FontanaShowers Customer Service: 800-684-4489
fontanashowers.com

FontanaShowers©
FontanaShowers©
FontanaShowers
FontanaShowers Customer Service: 800-684-4489
fontanashowers.com
Shower Head Installations Instruction
2
Shower Head Installations Instruction
Parts:
Step 3:
Step 1:
D
C
E
F F
According to drilling drawing sheet to
(B) mark the 4 drilling positions 1, then
use the Ø6mm drill to drill holes on the
wall according to the marked hole
position.
Inset the plug(D2) into the hole, hold the fix base (C) use the tapping screw (D1) through
fix base(C) holes, tighten the tapping screw (D1) tighten the top shower fixed bar(E) and
the inlet hose (F) with the fix base (C)

FontanaShowers©
FontanaShowers©
FontanaShowers
FontanaShowers Customer Service: 800-684-4489
fontanashowers.com
3
Fixed the top shower with the top shower fixed bar (E) , then connect with the inlet hose
(F) .
The installation is completed.
E
F
Step 5:
Step 6:

FontanaShowers©
FontanaShowers©
FontanaShowers
FontanaShowers Customer Service: 800-684-4489
fontanashowers.com
Step 7: Step 8:
Step 9: Step 10:
INPUT: 100-240V AC 1.1A 50/60Hz
OUTPUT: 12V AC 3.0A
LED Box
4

FontanaShowers©
FontanaShowers©
FontanaShowers
FontanaShowers Customer Service: 800-684-4489
fontanashowers.com
5
Step 2
Step 1
Step 4
Step 3
Step 6
Step 5
Digital Mixer 2 Way Installation Instructions

6
FontanaShowers©
FontanaShowers©
FontanaShowers
FontanaShowers Customer Service: 800-684-4489
fontanashowers.com
Step 8
Step 7
Step 10
Step 9
Notice
1. The control panel is sensitive, when installing it, please avoid to lel it ace directly to the water
from the hand shower and the head shower, because water will gel it misoperation or lock the
control panel.
2. The touch button is the best sensitive area.
3. The touch panel has water splash protection technology. When the system detect
misoperation, no response and need about 1 second to recover.
Function
Water TEMP adjust 2. Hand shower 3. Head Shower 4. Water flow adjust

FontanaShowers©
FontanaShowers©
FontanaShowers
FontanaShowers Customer Service: 800-684-4489
fontanashowers.com
7

FontanaShowers©
FontanaShowers©
FontanaShowers
FontanaShowers Customer Service: 800-684-4489
fontanashowers.com
8

FontanaShowers©
FontanaShowers©
FontanaShowers
FontanaShowers Customer Service: 800-684-4489
fontanashowers.com
9

FontanaShowers©
FontanaShowers©
FontanaShowers
FontanaShowers Customer Service: 800-684-4489
fontanashowers.com
Installation Of The Control Panel
1. Build the control panel into the shower panel
Step 1: Open a hole (6.7" X 3.7") on the shower panel, putting some glass cement around
the back of the control panel and fit it in the hole of the shower panel as picture shown.
Step 2: Fasten the mounting bracket onto the back of the control panel by screws.
Step 3: Install the host box on the back of the shower panel, connect the cold water and
hot water pipe, hand shower, and head shower's pipes.
1. Connect the G1/2" hot and cold water inlet pipes to the host box, tighten it and make
sure connection is well sealed (as the picture showed).
2. Connect the G1/2" water inlet pipe of the faucet to the water outlet pipe of the host box,
tighten it and make sure connection is well seated (as the picture is shown). Caution:
When installation, the hot water pipe, and the cold water pipe cannot mix up.
Otherwise, the system cannot work.
When you tighten the connector nut, torque should not exceed 8N M, GB 2.5N M is OK,
otherwise, it will damage the connector of the mixing valve and lead to water leaking.
Step 4: Connect the host box control cable with the control cable of shower faucet as an
arrow mark on the picture.
Caution: When connecting the two control cables, you must follow the arrow mark which
is shown in the cable joint. II riot, it will damage the cable joirlt.
Step 5: Connect the power supply cable of the host box with the adapter.
10

FontanaShowers©
FontanaShowers©
FontanaShowers
FontanaShowers Customer Service: 800-684-4489
fontanashowers.com
Recess Mounted Into Wall
According to the wall thickness, you can choose installation method A or B.
Method A: If the wall is thin, the host box and the shower control panel can be installed in
a different position.
Method B: If the wall is thick, the host box and the shower control panel can be installed
in the same position.
Method A:
Step 1: Open two-hole in the wall, and reserve space for the pipes and adapter.
Step 2: Drill four holes by 6mm diameter on the upside hole for install the wall bracket (as
the picture) and put the plastic screw into the hole.
Step 3: Drill four holes by 8mm diameter on the downside hole for the host box installa-
tion and put the expansion screws into the hole.
Step 4: Install the wall bracket of the control panel and the host box in two holes, accord-
ing to the pipe's position to set the host box position, adjust the screw of the wall bracket
to make sure it is concave the wall surface with a 0.5-1 mm difference.
Step 5: Connect the water pipe and the power supply cable of the host box, get water
supply to make sure the pipe has no leak. Connect the host box control cable to the con-
trol panel hole and fasten it, using the cement to seal the wall and cover it by the tiles.
Step 6: Connect the control cable between the host box and the control panel, put some
silicon on the back case of the control panel and put it on the wall bracket.
Method B: if the wall is thick
Step 1: Open one hole in the wall, and reserve space for the water pipes and power supply
cable.
Step 2: Drill four screw holes by 8mm diameter in the hole for the host box installation and
put the plastic screw into the holes.
Step 3: Fasten the control panel's bracket onto the host box by the M3 Self-tapping screws
provided. Install the host box which with the bracket into the hole by the plastic screw.
(according to the pipe's position to set the host box position), adjust the screw to make
sure the bracket's surface is lower than the wall surface with 0.5-1 mm.
Step 4: Connect the water pipe and the power supply cable of the host box, get water
supply to test the pipe no leak. Lead the host box control cable out to the control panel's
bracket and temporarily fasten it. And then use the cement to seal the wall and cover by
the tiles.
Step 5: Connect the control cable between the host box and the control panel, put some
silicon on the back case of the control panel and put it on the wall bracket.
11

FontanaShowers©
FontanaShowers©
FontanaShowers
FontanaShowers Customer Service: 800-684-4489
fontanashowers.com
12

FontanaShowers©
FontanaShowers©
FontanaShowers
FontanaShowers Customer Service: 800-684-4489
fontanashowers.com
13

FontanaShowers©
FontanaShowers©
FontanaShowers
FontanaShowers Customer Service: 800-684-4489
fontanashowers.com
Operation
1. Power on/off
Power on A. After electrify (The battery without electricity or not install battery), press the
fly-shuttle switch, power on and switch on the head shower automatically, adjust the ther-
mostatic Temp function. When you hear buzzer sound, the fly-shuttle switch and LCD
display would be lighting.
B. After electrify (The battery with electricity), press the fly-shuttle switch in 20 minutes
from last time turn it off. When power on, open the last time spray mode and TEMP
adjustable function (cold water or thermostatic function); if press the fly-shuttle switch
from more than 20 minutes from last time turn it off, power on and open the head spray
and TEMP adjustable function at the same time. You could hear buzzer sound, the
fly-shuttle switch and LCD display would be lighting.
C. When system is on, Water TEMP and water flow will be same as that you set last time.
Head shower (or hand shower) shows cursor and icon.
D. If you didn't set working time, default working time is 60 minutes.
Power off A. When system is on, press the fly-shuttle switch to power off system, you can
hear buzzer sound. B. The system will switch off automatically when working time comes
up.
Hand shower and head shower switch When the system is on, press Spray button on the
panel to switch the water outlet way between the head shower and hand shower. When
cursor and frame move to the head shower icon, the head shower comes water. When
cursor and frame move to the hand shower icon, hand shower comes water.
Setting When the system is on. rotate the fly-shuttle switch to adjust the water flow, press
the Setting button to adjust water TEMP and water flow. Press the Setting button and
keep for 3 seconds to set working time. System will restore to adjust water flow if no press
any button for 5 seconds.
Setting system on time When system is on, touch Setting panel switch to system on set-
ting, show Time icon. Rotating the fly-shuttle to setting system on time, counterclockwise
rotation is to reduce and clockwise rotation is to increase, setting range is 15-60 minutes.
You can hear a buzzer sound for each adjustment.
Stop setting for 5 seconds or touch Setting button, system on setting time TEMP will be
memory and exit system on-time setting, switch to water flow setting, close Time, icon.
Water TEMP adjust and cold water mode
When system is on, touch Setting button to enter into TEMP adjusting, cursor and frame
will move to TEMP cold icon. The °C icon on the LCD panel flash, at this time you could set
water TEMP from 29-48 °C. Rotate the fly-shuttle to adjust water TEMP and you can hear
buzzer sound for each step.
14

FontanaShowers©
FontanaShowers©
FontanaShowers
FontanaShowers Customer Service: 800-684-4489
fontanashowers.com
15
When the TEMP is lowest, rotating the fly-shuttle switch one round counter-clockwise to
enter into cold water mode, cursor and frame will move to the cold water icon. You can
hear buzzer sound when system enter into cold water mode. If you rotate the fly-shuttle
switch one round clockwise, system will enter into the water TEMP adjusting again.
If there's no touch on the panel for S seconds, water TEMP will be memory and exit the
water TEMP adjusting. Touch Setting button again to enter into water flow adjusting. °C
icon on the LCD panel will stop flashing. The fly-shuttle switch backlight color will change
according to the water TEMP as below.
blue color water TEMP <iii 33 °C blue;
orange color water TEMP < 41 °C;
red color >= 41 °C.
Water flow
When system is on, rotating the fly-shuttle switch to adjust water flow by default, if system
on other setting state, touching Setting button can switch to water flow setting. Cursor
and frame will move to the water flow icon . L on LCD panel flash, setting range is 4-18L
Rotating the fly-shuttle switch to adjust water flow, counter-clockwise rotating is to
reduce flow and clockwise rotating is to increase flow. You can hear a buzzer sound for
each adjustment. When water flow reaches the lowest and highest, no buzzer sound.
No touch on any button for 5 seconds, the water flow value will be saved. Or when you
touch Setting button, water flow value will be saved and switch to TEMP adjusting.
Working time setting
When system is on, keep pressing Setting button for 3 seconds, system will enter into the
working time setting icon Time will be shown on the LCD panel. Rotating the fly shuttle
switch to adjust the working time. The time range is1S-60 minutes. You can hear a buzzer
sound for each adjusting. No touch on any button for 5 seconds or press Setting button,
working time value will be saved and switch to TEMP adjusting.
Count down display
When system is on. the LCD panel shows count down for 60 minutes if the head shower
or hand shower is open.
Abnormal alarm
When water TEMP is over 49 Celsius degree, system will stop working and no water outlet
automatically. You could hear 3 times of buzzer sound. And the LCD panel shows error
code TE".

Step 1 Step 2
Step 3 Product Image
Hand Shower Outlet Installation
• Complete the outlet pipework ensuring it ends in an appropriate 15mm x 1/2" BSP female thread elbow.
Note: This fitting is not supplied as variations in installations require the selection of a suitable solder or
compression fitting.
• Install the 'Wall Outlet', thread long male 1/2" BSP into the appropriate female fitting using PTFE tape to
give a watertight joint.
Note: The thread can be cut to size if required. Make sure that all debris is removed from the connector
and the section that has been cut is dressed correctly, before installation.
The minimum required water pressure is 0.05 MPa (0.5 bar).
Flow rate 2.5 GPM (9.5 LPM).
Hand-Held Shower Installations Instructions
FontanaShowers©
FontanaShowers©
FontanaShowers
FontanaShowers Customer Service: 800-684-4489
fontanashowers.com
16

FontanaShowers
©
FontanaShowers©
FontanaShowers
FontanaShowers Customer Service: 800-684-4489
fontanashowers.com
17
Acid
Care & Cleaning
General Information
1. The product can be cleaned with warm water, a mild soap and a clean soft cloth.
2. Clean progressively and gently.
3. It is not required to use any abrasive cleaning pads, wire wool or cloths to clean the
product.
4. Avoid a vigorous cleaning action, as this could contribute to denaturing and dulling
5. Abrasive or strong cleaning products containing ammonia, bleaches, alcohol, dyes,
acids (hydrochloric, formic, phosphorus, chlorine or acetic) will be not be affected.
All products manufactured and supplied by Fontana are safe and comply to legislative
requirements. Providing they are installed correctly and receive regular maintenance in
accordance with these instructions your user experience will not be affected
6. If using a spray cleaner, apply the cleaning agent onto a soft cloth, never directly
spray onto the product as the cleaner may enter gaps and openings and cause
damage. Do not allow the cleaner to remain on the product for a period of time. After
cleaning, rinse thoroughly with clean water.