FORENO NORTH NRT73RBB User manual

9421027 598973
FORENO TAPWARE (NZ) LTD | Freephone: 0508 FORENO | [e-mail] | 5 Hewlett Street, Port Whangarei 0110 | FORENO.CO.NZ
NORTH Double Head Shower
Brushed Brass (PVD) NRT73RBB
Congratulations on your purchase of this high quality product from Foreno Tapware.
Please read the following before installation and retain (along with your receipt) for future reference.
TECHNICAL SPECIFICATIONS
Suitable for Mains Pressure only
Minimum Pressure = 150kPa
Maximum operating Pressure = 500kPa*
Maximum operating Temperature = 65 deg. Celsius
For domestic use only.
TOP INLET PLUMBING CONNECTION.
CONFIGURATION
Mains Pressure systems Install as supplied.
Unequal Low Systems Not suitable.
Equal Low systems Not suitable.
INSTALLATION
*FOR PRESSURES EXCEEDING 500KPA INSTALL A PRESSURE REDUCING VALVE. THOROUGHLY FLUSH ALL
PIPES TO ELIMINATE ANY REMAINING DIRT AND RESIDUE, AND INSTALL INLINE FILTERS. FAILURE TO DO
SO MAY VOID THE WARRANTY.
CAUTION: IF USING YOUR OWN SCREWS TO INSTALL THE WALL BRACKETS, DO NOT USE COUNTER SUNK TYPE
SCREWS, AS THIS WILL VOID THE WARRANTY.
• Refer installation diagram, overleaf.

=
PROUD PARTNER AND SUPPORTER OF MASTER PLUMBERS, GASFITTERS AND DRAINLAYERS
FORENO TAPWARE (NZ) LTD | Freephone: 0508 FORENO | [e-mail] | 5 Hewlett Street, Port Whangarei 0110 | FORENO.CO.NZ
ATTACH PROOF OF PURCHASE HERE
WARRANTY
PLEASE CALL US BEFORE REMOVING TAPWARE OR UNDERTAKING ANY REPAIR WORK.
Please refer to our website for warranty information: www.foreno.co.nz/warranty
In the unlikely event that this product fails during its warranty period, phone our Customer Service team
immediately on 0508 FORENO (0508 367 366) – as unauthorised removal of the product may void the warranty.
CARE AND MAINTENANCE
NOT TO BE CLEANED WITH ASTRINGENT, ABRASIVE OR CITRIC CLEANERS.
A so, damp cloth is recommended for cleaning. Mild soap solutions can also be used on occasion.
Apply teflon tApe
Shower wAll outlet,
25mm diAmeter hole
1
4
(2)
(2)
(1)
(1)
(1) (3)
(3)
(3)
(2)
(4)
(3)
(5)
(6)
2
5
3
puSh plAStic plug into drilled hole.
locAte bottom mounting AdApter over
hole, And Screw firmly into plAce.
inStAll the Shower heAd (1)
onto the top tube (2) by
Screwing into plAce.
enSure pre-inStAlled rubber
wASher iS in plAce (5).
Screw the Shower hoSe (3)
onto the hAnd piece.
enSure pre-inStAlled rubber
wASher iS in plAce (6).
connect the Shower hoSe (1)
to the bottom tube (2)
AS Shown.
the inStAllAlAtion iS now
complete.
turn on wAter Supply to check
for leAkS.
inStAll the bottom tube
(2) into the top tube (1) by
Screwing into plAce.
fit onto wAll by gently puShing
onto inlet connector And
lower mounting AdApter.
tighten m5 grub ScrewS (3)
with Allen key to fix into plAce.
MAINTENANCE AND CARE
Should only be cleaned with
mild liquid detergent or Soap.
donot uSe creAm cleAnerS,
AS they Are AbrASive.
the uSe of unSuitAble cleAning
AgentS mAy dAmAge the SurfAce.
Any dAmAge cAuSed in thiS wAy
will not be covered by wArrAnty.
remove red flow reStrictor
(iffitted).
Screw AdApter to
wAll outlet.
tighten with SpAnner.
7mm diAmeter hole
diverter operAtion
hAnd piece
overheAd roSe
MAX DISTANCE 760mm