FORTEZA F-S2000 User manual

F-S2000 ELECTRIC BOLT ACTION LOCK
INSTALLATION MANUAL
POWER SUPPLY:DC12V 1A.
OPERATION CURRENT 850mA, HOLDING CURRENT 300mA .
FAIL-SAFE TYPE (POWER LOCK)
DOOR SENSOR:N.C. & N.O
OPERATION DELEAY TIME:0 SEC. 2.5SEC. 5SEC. 9SEC.
BUILT-IN DELAYED EGRESS CONTROL POINT
FACE PLATE:200mm(L)x32mm(W)x40mm(D)
STRIKE PLATE:90mm(L)x26mm(W)x2mm(D)
PUSH BUTTON
AP-10
DC 12V
1A
+DC12V
RED
N.O.
F-S2000
N.C. COM
READER
ORANGE
※Please switch on the appliance again to validate any adjustment of
DIP switch value
0 SEC.
2.5 SEC.
5 SEC.
9 SEC.
Setting door lock delay timer :
BROWN
F-S2000 (6 PIN )
RED : + DC12V
BROWN : GND
YELLOW : DOOR POSITION SENSOR(N.C.)
GREEN : DOOR POSITION SENSOR(COM.)
ORANGE : PUSH BUTTON
BLUE : DOOR POSITION SENSOR(N.O.)
Page 1

Accessories:
X 1 Lock body X 1 Strike plate
X 2 Shims(small)
For strike plate X 2 Shims (Large) for
Lock body
SCREWS:
5-PIN Connector
Lock body
templates
Faceplate
X 8 Small wood screws for strike
plate( 4 x 8 mm)
X 4 Large metal screws for lock
body and shims( 5 x 8 mm)
Strike plate template
Time (sec.)
X4 Small metal screws for strike plate
and shims( 4 x 26 mm)
X 2 Large wood screws for lock
body( 5 x 15 mm)
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
900
800
700
400
600
500
300
200
100 Delay Time
Setting
Start
Stand-by
~ ~
Door Close
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
65
60
55
40
50
45
35
30
25
70
~ ~
Current
(mA)
Time (sec.)
Time (min.)
Temperature
(℃)
Supply power & door close
Current and Temperature Chart:
Page 2

Installation:
For double doors For single doors For single doors
Important-For vertical
mounting, wires must come
out the top of the unit.
Instruction:
Diagram 1: Dimensions
Diagram 2: For double door mounting
Diagram 3: For single door mounting
Diagram 4: For vertical mounting
Diagram 1
Diagram 2 Diagram 3 Diagram 4
Page 3

Strike plate
Faceplate
20mm
Installation:
Please make sure the correct
direction of the shims when mounted
For hollow metal doors: For wood doors:
45mm
Drill hole for deadbolt
(If wood door)
Drill hole for magnet
(if wood door)
Door
◆
The lock is hot?
The operating temperature of the lock is normally within 55℃.
◆
No operation after installation?
1.Please check power supply. 2.Please check if the direction of
the template is being installed correctlly 3.Please check the
connection points(N.O or N.C)
◆
Lock will open when force is applied on the reader (eg. Hitting
hard or vibrating the reader).?
1.Please check all the connections .
2.Reader's N.C points might strike immediately when force is
being applied on it this eventually causes the fail-safe type of lock
to open when sudden power cut occured. Please refer to page 1
for wiring to prevent such case happen.
Question & Answer
19.6.V1.E Page 4