Sargent and Greenleaf 2740 User manual

page 1
Model 2740 High Security Safe Lock
Installation Instructions
Copyright© 2010, Sargent & Greenleaf
Document 630-745
Revised 7/22/2010
Mounting Considerations:
• This lock requires setup and adjustment with
the use of a setup module after installation. The
installation cannot be completed without the use
of a setup module. Setup modules are only issued
to S&G Certified Technicians who have sucessfully
completed specialized training on the 2740 lock.
• The Sargent & Greenleaf 2740 safe lock is
designed to use the same mounting screw
locations as common S&G mechanical and
electronic safe locks. In most instances it can
easily be mounted in place of these locks.
• The 2740 lock bolt is drilled and tapped to
accept an extension, if necessary. When attaching anything to the lock bolt,
make sure the end of the lock bolt (not the extension) can retract within 0.125 inch (3 mm) of being flush with the
end of the lock case.
• The 2740 accommodates right-hand, left-hand, vertical-up and vertical-down mounting applications. A single model
can be splined for any of these applications during the installation process.
• The dial ring diameter is approximately 3 ¾ inches, matching the diameter of the majority of S&G dial rings.
• Each 2740 lock and cover is configured to work together. If installing multiple locks, be very careful to avoid using
a cover with any lock other than the one with which it was shipped from S&G’s factory.
• Each 2740 lock requires one CR2450 coin cell battery and one CR123A lithium camera-type battery. Any time
one battery is replaced, the other should be replaced. Fresh batteries should be included with your lock. If not, be
careful to avoid using partially drained batteries.
• Modifications to the lock are not recommended and will void the manufacturer’s warranty.
• Personal information that can be directly related to a combination holder, such as a birth date, street number, or
phone number, should not be used in creating a lock code. Avoid combinations that could be easily guessed. Be
sure to change the combination from the factory setting 50-25-50 to one of your own choosing.
• The S&G 2740 is warranted against defects in materials and workmanship. This warranty applies only to locks
installed and set up by an S&G certified technician.
Sargent & Greenleaf, Inc.
A Wholly Owned Subsidiary of Stanley Security Solutions, Inc.
PO Box 930, Nicholasville, Kentucky 40340-0930 USA
Phone [phone]
Phone [phone]
FAX [phone]
FAX [phone]
Sargent & Greenleaf S.A.
9, chemin du Croset
1024 Ecublens, Switzerland
Phone [phone]
FAX [phone]

page 2
Installation Notes
The Sargent & Greenleaf model 2740 lock was designed to meet Federal Specification FF-L-2740A. It
can be retrofit to most security containers currently in service.
It is necessary to remove only the lock cover for installation. All other parts should remain in place as received from the
manufacturer.
Most safes and cabinets will already be prepped for lock installation. In the unlikely event that this is not
the case, locate exact position you want for the lock on the mounting plate. Using the template on the
last page of these instructions, drill and tap four holes for the attaching screws (1⁄
4" X 20 or M6 for metric
applications). Using the template, drill a hole for the spindle through the mounting plate. The minimum
spindle hole diameter is 3⁄
8" (9,5 mm). The optimum hole size is 1⁄ 2" (12,7 mm) diameter.
Wear the included static discharge wrist strap whenever you are about to remove the lock cover, or
whenever the cover is off of the lock body. The strap should be grounded to any bare metal of the safe
(container).
It is necessary to remove only the cover when attaching the lock. All other parts should remain in
place as received from the factory. When the cover is off of the lock, handle it carefully. It houses the
microprocessor and related circuitry. Do not touch the circuit board.
INSTALLATION INSTRUCTIONS
1. Make sure the lock bolt is in the extended position (Figure 1). Carefully remove the lock cover.
CAUTION: Handle the cover by its edges. Do not touch the circuit board or pin towers. Any inadvertent contact
may introduce a static discharge which will damage the electronics. Static discharge may cause immediate
lock failure or delayed failure.
CAUTION: Do not attempt to remove the drive cam or the lever.
2. Mount the lock body in place with four 1
⁄
4 X 20 attaching screws provided (Figure 1). Apply one drop
of Loctite 242® threadlocker to the threads of each mounting screw near the tip. No Loctite should be
allowed to contaminate the inside of the lock case.
Figure 1
Extended
Lock Bolt
Drive Cam
Mounting Screw Locations
(indicated by white circles)
Lever
3. Attach the dial ring to the front of the safe or cabinet by loosely installing the
attaching screws to hold the dial ring in place for alignment. The dial ring
opening index should be at the 12 o’clock center position (Figure 3).
Figure 3
Opening Index

page 3
7. Measure and/or mark the excess
spindle that projects beyond the
recessed inner surface of the drive
cam (Figure 5). When the spindle
is cut to length, it can be as much
as two threads short of flush with
the surface of the drive cam, but it
cannot extend beyond flush.
8. Remove the dial without moving the dial ring out alignment. Remove one dial ring screw, apply a drop
of Locktite® 242 threadlocker to the threads near the tip, re-install the screw, and tighten firmly. Do the
same with the remaining screw. Remove the masking tape used to temporarily hold the ring in alignment.
9. Remove the spring and washers from the dial. Cut off the excess spindle where you marked it, and
remove any burrs from the end. You may also find that the spindle threads more easily into the drive
cam if you bevel the end of the freshly cut spindle slightly. Do not discard the excess spindle piece as
you may use it to seat the spline key later in the installation.
Figure 4
Misaligned
Dial Edges Flush
with Ring
Aligned
Note that the small gap between the dial and ring is uneven when the dial ring is misaligned, but is even when the dial ring is properly
aligned. The center of a properly aligned dial ring is in perfect alignment with the center of the spindle hole in the drive cam.
Excess Spindle
Figure 5
Mark Here
4. Slide the dial spring over the spindle hub at the base of the
spindle. Place the metal dial washer on top of the spring, then
the white washer on top of the metal washer, as shown in the
photo to the right.
5. Hold the drive cam in place in the lock case with one hand and
thread the dial/spindle assembly into the cam until the dial’s
edge is flush with the top of the dial ring (Figure 4, far right) or
until the dial stops. Make sure the flat washer and spring stay in
place on the spindle hub while installing the dial into the cam.
Caution: When threading the dial into the cam, be careful to avoid
putting excessive pressure on the cam by pushing the spindle
against it.
6. The alignment of the dial and ring is important to the proper operation of the lock. Very good alignment
must be obtained. The dial should be flush and centered with the top surface of the dial ring for true
centering (Figure 4). When the dial ring is as perfectely aligned as possible, use masking tape to hold
it in position. Use several pieces of tape to make sure it doesn’t move out of alignment.

page 4
10. With the dial spring and flat washer in place, insert the dial into the lock. Hold the drive cam in
place, positioned for its gate (Figure 6) to receive the fence of the lever assembly, and thread the dial
into the cam until the top of the dial is flush with the top surface of the dial ring (Figure 4, far right)
or until the dial stops.
11. Turn the dial counterclockwise until zero is aligned with the opening index of the dial ring. If it was
necessary to turn the dial less than ½ turn, back it out of the drive cam one additional revolution. The
proper spindle spline keyway and drive cam spline keyway should now be closely aligned.
12. After the spline keyways are aligned, insert the spline key as far as you can with your fingers
(sequence in Figure 7). Make sure the spline key is oriented to fit into the recess in the cam. It
will only fit properly one way. The spindle and cam are now correctly splined for the way the lock is
mounted (RH, LH, VU, or VD). Use a pin punch or the piece of excess spindle you cut off in Step 9 to
carefully tap the spline key until its underside just touches the top surface of the drive cam. Be very
careful to avoid striking anything other than the spline key. With the spline key fully seated, the dial
must turn freely with no rubbing or interference. Once the spline key is seated, install the included
2-56 spline key screw firmly, but do not overtighten. If desired, you can carefully apply a very small
amount (much less than a drop) of Loctite® 242 threadlocker to the screw threads near the tip before
installing it.
Figure 6
Spline Key
Gate
Figure 7
Note: You can easily remove the spline key after removing the 2-56 screw by
threading the longer of the lock’s two cover screws into the center of the spline
key. As you turn the screw into the spline key, the key will be extracted. This
spline key is reusable.
LH Mount
RH Mount
VU Mount
VD Mount

page 5
13. Install the two batteries in the underside of the cover (Figure 8). The circular coin cell battery goes in
first, positive side up. Then the camera-type battery is inserted as shown. When the coin cell battery
and then the main battery are installed, you will hear a beep. If you do not hear the beep, remove
both batteries for one minute, then repeat the installation process. Always insert the coin cell battery
first then the camera-type battery. Ten seconds after the batteries are installed, the lock does a
battery check. If the battery check passes, another beep will be heard. If not, remove both batteries
for one minue, then repeat the battery installation process. If the second battery installation does not
produce the two beeps, repeat the battery installation process using new batteries.
14. Place the cover on the lock body, and fasten with the two screws provided. The longer screw goes in
the cover screw opening closest to the change key receptacle (Figure 9). Tighten securely.
Figure 9
Change Key
Receptacle
15. The Spy-Proof® dial cover is attached to
the dial ring at two points (Figure 10), one
on each side of the dial ring. The cover is
attached using a 4-40 socket head cap
screw (requiring a 3/32” hex driver) at each
of the two locations. Put one small drop of
Loctite 242® threadlocker on the tip of each
cap screw before installing. The cover does
not need to be removed for combination
changing. The Spy-Proof® cover must
be installed for the lock to meet Federal
Specifications.
Figure 8
Figure 10

page 6
16. Again, check to make sure the dial turns freely.
17. Place the self-adhesive orange label inside the safe or container, where it is readily visible when the
door or locking drawer is open. For instance, the locking drawer’s inside cover is a good location.
There is also a 5/8" wide label on the same sheet that is sized to fit on the top surface of file drawer
back plates (Figure 11), where it will be in plain view of anyone who opens the drawer.
The lock installation is complete. Refer to the operating instructions for calibration and combination
setting procedures. The installation is not complete until the lock is calibrated.
1 15
⁄
16" (49,2 mm)
(17,5 mm)
11
⁄
16"13
⁄
16"
(20,6 mm)
RIGHT-HAND
LEFT-HAND
VERTICAL-UP
VERTICAL-DOWN
LOCK TEMPLATE
Figure 11