Fortinet FortiAnalyzer-2000B User manual

FortiAnalyzer-2000B®
Version 4.0 MR1
Rack and Hardware Install Guide

FortiAnalyzer-2000B Rack and Hardware Install Guide
Version 4.0 MR1
5 January 2010
Revision 1
© Copyright 2009 Fortinet, Inc. All rights reserved. No part of this publication including text, examples,
diagrams or illustrations may be reproduced, transmitted, or translated in any form or by any means,
electronic, mechanical, manual, optical or otherwise, for any purpose, without prior written permission of
Fortinet, Inc.
Trademarks
Dynamic Threat Prevention System (DTPS), APSecure, FortiASIC, FortiBIOS, FortiBridge, FortiClient,
FortiGate®, FortiGate Unified Threat Management System, FortiGuard®, FortiGuard-Antispam,
FortiGuard-Antivirus, FortiGuard-Intrusion, FortiGuard-Web, FortiLog, FortiAnalyzer, FortiManager,
Fortinet®, FortiOS, FortiPartner, FortiProtect, FortiReporter, FortiResponse, FortiShield, FortiVoIP, and
FortiWiFi are trademarks of Fortinet, Inc. in the United States and/or other countries. The names of actual
companies and products mentioned herein may be the trademarks of their respective owners.
Regulatory compliance
FCC Class A/Class B Part 15 CSA/CUS
Caution: Risk of explosion if battery is replaced by incorrect type.
Dispose of used batteries according to instructions

Contents
FortiAnalyzer-2000B Version 4.0 MR1 Rack and Hardware Install Guide
Revision 1 1
http://docs.fortinet.com/ • Feedback
Contents
Introduction .............................................................................................. 3
Registering your Fortinet product................................................................................. 3
Customer service and technical support...................................................................... 3
Fortinet documentation ................................................................................................. 3
Fortinet Tools and Documentation CD ....................................................................... 4
Fortinet Knowledge Base ........................................................................................... 4
Comments on Fortinet technical documentation ....................................................... 4
Conventions .................................................................................................................... 4
IP addresses............................................................................................................... 4
CLI constraints............................................................................................................ 4
Notes, Tips and Cautions ........................................................................................... 4
Typographical conventions......................................................................................... 4
Rack Installation Instructions................................................................. 7
Removing the system from the rack ......................................................................... 12
Cable Management Arm Installation ........................................................................... 13
Installing the Bezel........................................................................................................ 18
Connecting the Keyboard, Mouse, and Monitor ........................................................ 19
Connecting the Power Cables ..................................................................................... 20
Securing the Power Cord ............................................................................................. 20
Turning on the System ................................................................................................. 21
Installing Hard Drives ............................................................................ 23
Hard Drives............................................................................................................... 23
Mixed SAS/SATA Hard-Drive Configurations .................................................... 23
Removing a Hard-Drive Blank............................................................................ 23
Installing a Hard-Drive Blank.............................................................................. 24
Removing a Hot-Swap Hard Drive ..................................................................... 24
Installing a Hot-Swap Hard Drive ....................................................................... 24
Removing a Hard Drive From a Hard-Drive Carrier ........................................... 25
Installing a Hard Drive Into a Hard-Drive Carrier ............................................... 25
Index........................................................................................................ 27

Contents
FortiAnalyzer-2000B Version 4.0 MR1 Rack and Hardware Install Guide
2Revision 1
http://docs.fortinet.com/ • Feedback

Introduction Registering your Fortinet product
FortiAnalyzer-2000B Version 4.0 MR1 Rack and Hardware Install Guide
Revision 1 3
http://docs.fortinet.com/ • Feedback
Introduction
Welcome and thank you for selecting Fortinet products for your network protection.
FortiAnalyzer units are network appliances that provide integrated log collection and
reporting tools. Reports analyze logs for email, FTP, web browsing, security events, and
other network activity to help identify security issues and reduce network misuse and
abuse.
In addition to logging and reporting, FortiAnalyzer units also have several major features
that augment or enable certain FortiGate unit functionalities, such as DLP archiving and
quarantining, and improve your ability to stay informed about the state of your network.
This chapter contains the following topics:
•Registering your Fortinet product
•Customer service and technical support
•Fortinet documentation
•Conventions
Registering your Fortinet product
Before you begin, take a moment to register your Fortinet product at the Fortinet Technical
Support web site, https://support.fortinet.com.
Many Fortinet customer services, such as firmware updates, technical support, and
FortiGuard Antivirus and other FortiGuard services, require product registration.
For more information, see the Fortinet Knowledge Base article Registration Frequently
Asked Questions.
Customer service and technical support
Fortinet Technical Support provides services designed to make sure that your Fortinet
products install quickly, configure easily, and operate reliably in your network.
To learn about the technical support services that Fortinet provides, visit the Fortinet
Technical Support web site at https://support.fortinet.com.
You can dramatically improve the time that it takes to resolve your technical support ticket
by providing your configuration file, a network diagram, and other specific information. For
a list of required information, see the Fortinet Knowledge Base article Fortinet Technical
Support Requirements.
Fortinet documentation
The Fortinet Technical Documentation web site, http://docs.fortinet.com, provides the
most up-to-date versions of Fortinet publications, as well as additional technical
documentation such as technical notes.
In addition to the Fortinet Technical Documentation web site, you can find Fortinet
technical documentation on the Fortinet Tools and Documentation CD, and on the Fortinet
Knowledge Center.

Conventions Introduction
FortiAnalyzer-2000B Version 4.0 MR1 Rack and Hardware Install Guide
4Revision 1
http://docs.fortinet.com/ • Feedback
Fortinet Tools and Documentation CD
Many Fortinet publications are available on the Fortinet Tools and Documentation CD
shipped with your Fortinet product. The documents on this CD are current at shipping
time. For current versions of Fortinet documentation, visit the Fortinet Technical
Documentation web site, http://docs.fortinet.com.
Fortinet Knowledge Base
The Fortinet Knowledge Base provides additional Fortinet technical documentation, such
as troubleshooting and how-to-articles, examples, FAQs, technical notes, and more. Visit
the Fortinet Knowledge Base at http://kb.fortinet.com.
Comments on Fortinet technical documentation
Please send information about any errors or omissions in this or any Fortinet technical
document to [email protected].
Conventions
Fortinet technical documentation uses the conventions described below.
IP addresses
To avoid publication of public IP addresses that belong to Fortinet or any other
organization, the IP addresses used in Fortinet technical documentation are fictional and
follow the documentation guidelines specific to Fortinet. The addresses used are from the
private IP address ranges defined in RFC 1918: Address Allocation for Private Internets,
available at http://ietf.org/rfc/rfc1918.txt?number-1918.
CLI constraints
CLI constraints, such as <address_ipv4>, indicate which data types or string patterns
are acceptable input for a given parameter or variable value. CLI constraint conventions
are described in the CLI Reference document for each product.
Notes, Tips and Cautions
Fortinet technical documentation uses the following guidance and styles for notes, tips
and cautions.
Typographical conventions
Fortinet documentation uses the following typographical conventions:
Tip: Highlights useful additional information, often tailored to your workplace activity.
Note: Also presents useful information, but usually focused on an alternative, optional
method, such as a shortcut, to perform a step.
Caution: Warns you about commands or procedures that could have unexpected or
undesirable results including loss of data or damage to equipment.

Introduction Conventions
FortiAnalyzer-2000B Version 4.0 MR1 Rack and Hardware Install Guide
Revision 1 5
http://docs.fortinet.com/ • Feedback
Table 1: Typographical conventions in Fortinet technical documentation
Convention Example
Button, menu, text box,
field, or check box label
From Minimum log level, select Notification.
CLI input config system dns
set primary <address_ipv4>
end
CLI output FGT-602803030703 # get system settings
comments : (null)
opmode : nat
Emphasis HTTP connections are not secure and can be intercepted by
a third party.
File content <HTML><HEAD><TITLE>Firewall
Authentication</TITLE></HEAD>
<BODY><H4>You must authenticate to use this
service.</H4>
Hyperlink Visit the Fortinet Technical Support web site,
https://support.fortinet.com.
Keyboard entry Type a name for the remote VPN peer or client, such as
Central_Office_1.
Navigation Go to VPN > IPSEC > Auto Key (IKE).
Publication For details, see the FortiAnalyzer Rack and Hardware
Install Guide.

Conventions Introduction
FortiAnalyzer-2000B Version 4.0 MR1 Rack and Hardware Install Guide
6Revision 1
http://docs.fortinet.com/ • Feedback

Rack Installation Instructions
FortiAnalyzer-2000B Version 4.0 MR1 Rack and Hardware Install Guide
Revision 1 7
http://docs.fortinet.com/ • Feedback
Rack Installation Instructions
The FortiAnalyzer-2000B comes with a sliding rail kit. Use the instructions below to install
the rails.
To install the sliding rail kit
1Locate the components for installing the rail kit assembly:
• Two sliding rail assemblies (1)
• Two Velcro straps (2)
Figure 1: Rail kit contents
2In square-hole racks, do the following:
• Position the left and right rail end pieces of the rail module labeled FRONT facing
inward and orient each end piece to seat in the square holes on the front side of the
vertical rack flanges (3).
Caution: Only trained service technicians are authorized to remove the system cover and
access any of the components inside the system. Before you begin, review the safety
instructions that came with the system.
Note: The illustrations in this document are not intended to represent a specific server.
1
2

Rack Installation Instructions
FortiAnalyzer-2000B Version 4.0 MR1 Rack and Hardware Install Guide
8Revision 1
http://docs.fortinet.com/ • Feedback
Figure 2: Installing and removing the rails (square-hole racks)
• Align each end piece to seat the pegs in the bottom hole of the first U and the top
hole of the second U (4).
• Engage the back end of the rail until it fully seats on the vertical rack flange and the
second “tooth” on the latch locks in place. Repeat these steps to position and seat
the front end piece on the vertical flange (5).
• To remove the rails, pull on the latch release button on the end piece midpoint and
unseat each rail (6).
3In round-hole racks, do the following:
• Position the left and right rail end pieces of the rail module labeled FRONT facing
inward and orient each end piece to seat in the round holes on the front side of the
vertical rack flanges (7).
3
6
5
4

Rack Installation Instructions
FortiAnalyzer-2000B Version 4.0 MR1 Rack and Hardware Install Guide
Revision 1 9
http://docs.fortinet.com/ • Feedback
Figure 3: Installing and removing the rails (round-hole racks)
• Align each end piece to seat the pegs in the bottom hole of the first U and the top
hole of the second U (8).
• Engage the back end of the rail until it fully seats on the vertical rack flange and the
first “tooth” on the latch locks in place. Repeat these steps to position and seat the
front end piece on the vertical flange (9).
• To remove the rails, pull on the latch release button on the end piece midpoint and
unseat each rail (10).
4To install the system into the rack, do the following:
• Pull the inner slide rails out of the rack until they lock into place (11).
7
8
9
10

Rack Installation Instructions
FortiAnalyzer-2000B Version 4.0 MR1 Rack and Hardware Install Guide
10 Revision 1
http://docs.fortinet.com/ • Feedback
Figure 4: Installing the system on the rack
• Locate the three shoulder screws on one side of the system and lower them into the
J-slots on the slide assembly (12).
• Seat the three screws on the other side, lowering the system until all shoulder
screws engage in the J-slots (13).
• Push the system inward until the front release latch clicks into place. Press the
slide-release lock buttons on both rails and slide the system into the rack (14).
5To engage and release the slam latch, do the following:
• Facing the front, locate the slam latch on either side of the system (15).
11
12
13
14

Rack Installation Instructions
FortiAnalyzer-2000B Version 4.0 MR1 Rack and Hardware Install Guide
Revision 1 11
http://docs.fortinet.com/ • Feedback
Figure 5: Engaging and releasing the slam latch
• The latches engage automatically as the system is pushed into the rack and are
released by pulling up on the latches (16).
• To secure the system for shipment in the rack or for other unstable environments,
locate the hard-mount screw under each latch and tighten each screw with a #2
Phillips screwdriver (17).
6To route the cables, do the following:
• Locate the inner and outer CMA brackets on the interior sides of both rack flanges
(18).
15
16
17

Rack Installation Instructions
FortiAnalyzer-2000B Version 4.0 MR1 Rack and Hardware Install Guide
12 Revision 1
http://docs.fortinet.com/ • Feedback
Figure 6: Routing the cables
• Bundle the cables gently, pulling them clear of the system connectors to the left and
right sides (19).
• Thread the Velcro straps through the tooled slots on the outer or inner CMA
brackets on each side of the system to secure the cable bundles (20).
Removing the system from the rack
To remove the system from the rack
1Locate the lock levers on the front ends of both inner rails (1).
18
20
19

Rack Installation Instructions Cable Management Arm Installation
FortiAnalyzer-2000B Version 4.0 MR1 Rack and Hardware Install Guide
Revision 1 13
http://docs.fortinet.com/ • Feedback
Figure 7: Removing the system from the rack
2Pull up on each lever into the release position to unlock (2).
3Grasp the sides of the system firmly and pull forward and up to unseat the system from
the J-slots. Lift the system up and away from the rack and place on a level surface (3).
Cable Management Arm Installation
The FortiAnalyzer-2000B comes with a Cable Management Arm. Use the instructions
below to install the Cable Management Arm.
To install the cable management arm
1Locate the components for installing the Cable Management Arm (CMA) assembly:
• Cable Management Arm tray (1)
• Cable Management Arm (2)
• Nylon cable tie wraps (3)
1
3
2
Caution: Only trained service technicians are authorized to remove the system cover and
access any of the components inside the system. Before you begin, review the safety
instructions that came with the system.
Note: The illustrations in this document are not intended to represent a specific server.

Cable Management Arm Installation Rack Installation Instructions
FortiAnalyzer-2000B Version 4.0 MR1 Rack and Hardware Install Guide
14 Revision 1
http://docs.fortinet.com/ • Feedback
Figure 8: Cable Management Arm kit contents
2To install or remove the Cable Management Arm Tray, do the following:
• Align and engage each side of the tray with the receiver brackets on the inner
edges of the rails and push forward until the tray clicks into place (4).
1
2
3
Note: To secure the CMA for shipment in the rack, loop the tie wraps around both baskets
and tray and cinch them firmly. For larger CMAs, the tie wraps can be threaded through the
inner and outer baskets and around the tray to secure them. Securing the CMA in this
manner will also secure your system in unstable environments.
Note: The CMA tray provides support and acts as a retainer for the CMA.

Rack Installation Instructions Cable Management Arm Installation
FortiAnalyzer-2000B Version 4.0 MR1 Rack and Hardware Install Guide
Revision 1 15
http://docs.fortinet.com/ • Feedback
Figure 9: Installing and removing the Cable Management Arm Tray
• To remove the tray, squeeze the latch-release buttons on both sides toward the
center and pull the tray out of the receiver brackets (5).
3To install and remove the CMA, do the following:
• At the back of the system, fit the latch on the front end of the CMA on the innermost
bracket of the slide assembly until the latch engages (6).
5
4
Note: You can attach the CMA to either the right or left mounting rail, depending on how
you intend to route cables from the system. Mounting the CMA on the side opposite of the
power supplies is recommended; otherwise, the CMA must be disconnected in order to
remove the outer power supply. You must remove the tray before removing the power
supplies.

Cable Management Arm Installation Rack Installation Instructions
FortiAnalyzer-2000B Version 4.0 MR1 Rack and Hardware Install Guide
16 Revision 1
http://docs.fortinet.com/ • Feedback
Figure 10: Installing and removing the Cable Management Arm
• Fit the other latch on the end of the outermost bracket until the latch engages (7).
• To remove the CMA, disengage both latches by pressing the CMA release buttons
at the top of the inner and outer latch housings (8).
4To move the CMA away from the CMA tray, do the following:
• The CMA can be pulled away from the system and extended away from the tray for
access and service (9).
6
7
8

Rack Installation Instructions Cable Management Arm Installation
FortiAnalyzer-2000B Version 4.0 MR1 Rack and Hardware Install Guide
Revision 1 17
http://docs.fortinet.com/ • Feedback
Figure 11: Moving the CMA away from the CMA tray
• At the hinged end, lift the CMA up and off of the tray to unseat it from the tray catch.
Once it is unseated from the tray, swing the CMA away from the system (10).
5To cable the system using the CMA, do the following:
• Using the tie wraps provided, bundle the cables together as they enter and exit the
baskets so they do not interfere with adjacent systems (11).
9
10
Note: You can also extend the CMA into the service position once it is cabled to access the
back of the system.
Caution: To avoid potential damage from protruding cables, secure any slack in the status
indicator cable before routing this cable through the CMA.

Installing the Bezel Rack Installation Instructions
FortiAnalyzer-2000B Version 4.0 MR1 Rack and Hardware Install Guide
18 Revision 1
http://docs.fortinet.com/ • Feedback
Figure 12: Cabling the system using the CMA
• With the CMA in the service position, route the cable bundle through the inner and
outer baskets (12).
• Use the preinstalled Velcro straps on either end of the baskets to secure the cables
(13).
• Adjust the cable slack as needed at the hinge position (14).
• Swing the CMA back into place on the tray (15).
• Install the status indicator cable at the back of the system and secure the cable by
routing it through the CMA. Attach the other end of this cable to the corner of the
outer CMA basket. (16).
Installing the Bezel
A lock on the bezel restricts access to the power button, optical drive, and hard drive(s).
The LCD panel and navigation buttons are accessible through the front bezel.
To remove the Front Bezel
1Using the system key, unlock the bezel.
2Pull up on the release latch next to the key lock.
3Rotate the left end of the bezel away from the system to release the right end of the
bezel.
4Pull the bezel away from the system. See Figure 13.
11
12
13
14 15
16