Fortinet FortiWiFi 60CM User manual

FortiWiFi 60CM
QuickStart Guide

Auguest 20, 2013
01-430-135194-20130820
Copyright© 2013 Fortinet, Inc. All rights reserved. Fortinet®, FortiGate®, and
FortiGuard®, are registered trademarks of Fortinet, Inc., and other Fortinet
names herein may also be trademarks of Fortinet. All other product or company
names may be trademarks of their respective owners. Performance metrics
contained herein were attained in internal lab tests under ideal conditions, and
performance may vary. Network variables, different network environments and
other conditions may affect performance results. Nothing herein represents any
binding commitment by Fortinet, and Fortinet disclaims all warranties, whether
express or implied, except to the extent Fortinet enters a binding written contract,
signed by Fortinet’s General Counsel, with a purchaser that expressly warrants
that the identified product will perform according to the performance metrics
herein. For absolute clarity, any such warranty will be limited to performance in
the same ideal conditions as in Fortinet’s internal lab tests. Fortinet disclaims
in full any guarantees. Fortinet reserves the right to change, modify, transfer, or
otherwise revise this publication without notice, and the most current version of
the publication shall be applicable.

Table of Contents
Package Contents 1
Connecting Your Device 2
FortiExplorer 3
Connecting to the FortiWiFi Unit 5
Technical Specifications 6
LED Specifications 7
Cautions and Warnings 8
Documentation and Links 12
Register Your Product 13
Product License Agreement 14

Package Contents
USB Cable
Power Adapter
Ethernet Cable
Power Cable
The unit should be placed farther than 75mm on each side from a heat source. If you
are mounting more than one unit, place them in a vertical row to provide better ventila-
tion.
Required Materials:
Drill bit: Size is determined by the screw size.
Anchors: Twofor mounting on dry-wall, plasterboard, or gyprock.
Screws: Twoappropriate for anchors. Maximum diamter of 3.5mm.
Instructions:
1. Tapethis template to the wall in the desired location.
2. Mark the position of the drill holes on the wall.
3. Drill two holes.
4. Insert anchors into drilled holes.
5. Insert the screws into the anchors. Screws should protrude 5mm out of wall.
6. Place FortiWifi key holes over the screws and slide the unit down into position. The
FortiWifi can be placed in either position shown below.
Wall-Mount Template
FortiWifi 60 Series Devices
Drill hole Drill hole
Wall-mount
Template
Wireless
Antennae
FortiWiFi 60CM
QuickStart Guide
QuickStart Guide
Thank you for purchasing the FortiWiFi 60CM. The FortiWiFi 60CM multi-threat
security appliance offers you unmatched performance, flexibility, and security for
your remote, branch, or small office network.
Your box contains the following:
FortiWifi 60CM
QuickStart Guide
USB Cable
Ethernet cable
Power Cable
Power Adapter
2 Wireless Antennae
Wall mount template
Page 1
Note: Accessories may not be exactly as shown.

Connecting Your Device
Page 2
To attach your unit to a wall, refer to the wall mount template.
Ensure the FortiWiFi unit is placed on a stable surface. Connect the
following to the FortiWiFi unit:
1. Connect an Ethernet cable into the port labeled WAN1.
2. Connect the other end of your Ethernet cable to your Internet
connection.
3. Connect an Ethernet cable to each workstation or laptop PC you
wish to connect to the FortiWiFi unit.
4. Connect an RJ-11 telephone cable to the MODEM port.
5. Connect the provided antennae.
6. Connect the Power Supply to the FortiWiFi unit and plug the cable
into an electrical outlet.
ExpressCard Slot
Optionally, you may also insert a wireless Internet modem into the
ExpressCard slot for wireless connectivity to the Internet.
CONSOLE
WAN1WAN2
USBDC+12V 5 1234
USB MGMT DMZ MODEM
2
133
6
5 5
4

FortiExplorer
FortiExplorer provides a user-friendly tool that you can use to
configure a FortiWiFi unit over a standard USB connection, rather
than using a console cable or Ethernet connection.
Caution: Do not connect the USB cable until after FortiExplorer
has been installed.
Note: When using FortiExplorer for the first time, ensure the FortiWiFi
unit is using its factory default settings.
Installing FortiExplorer
FortiExplorer is available for Microsoft Windows XP, Vista, 7, and 8. It
is also available for Mac OS X Snow Leopard and higher.
Microsoft Windows Install
1. Extract the ZIP file (if downloaded) and double-click the .msi, or .exe
file and follow the instructions on-screen.
2. Connect the USB cable to the FortiWiFi unit and then to the
management computer.
3. The FortiExplorer Easy Configuration Utility opens when the USB
cable is connected. Select Install the hardware automatically and
select Next.
4. After a moment, FortiExplorer will launch.
CONSOLE
WAN1WAN2
USBDC+12V 5 1234
USB MGMT DMZ MODEM
USB Cable
USB A cable end into
Management Computer
USB B cable end into
your Fortinet device
Page 3

Mac OS Install
1. Double-click the .dmg file and drag the FortiExplorer program file
into the Applications folder.
2. Connect the USB cable to the FortiWiFi unit and then to the
management computer.
3. Double-click the FortiExplorer icon to launch the application.
Configuration Options
With FortiExplorer, you are provided a number of options on how to
configure the FortiWiFi unit, depending on your level of comfort with
various interfaces.
Updating FortiExplorer and Firmware
FortiExplorer may be automatically updated from time to time.
You can also use FortiExplorer to check for new firmware for a
FortiGate unit. To check for new firmware, select the FortiGate unit
from the device list and select Check for New Firmware. FortiExplorer
will also monitor firmware updates for your devices and provide an
alert when one is available.
Page 4

Connecting to the FortiWiFi Unit
The FortiWiFi unit requires some basic configuration to add it to your
network. These basic steps include assigning IP addresses, DNS
settings, and the default gateway. Until these steps are completed
traffic will not flow through the device.
In addition to FortiExplorer, the FortiWiFi unit can be configured using
the Web-based Manager or the Command Line Interface (CLI).
This section will step you through both methods of connecting to the
unit. Use whichever method you are most comfortable with.
To Connect to the Web-based Manager:
1. Connect the FortiWiFi unit’s port 1 to a management computer using
the provided Ethernet cable.
2. Configure the management computer to be on the same subnet as
the internal interface of the FortiWiFi unit:
a. Browse to the Network and Sharing Center > Change Adapter
Settings > Local Area Connection Properties > Internet Protocol
Version 4 (TCP/IPv4) Properties.
b. Change the IP address of the management computer to
192.168.1.2 and the netmask to 255.255.255.0.
3. To access the FortiWiFi unit’s Web-based Manager, start a browser
of your choice and browse to https://192.168.1.99 (remember to
include the “s” in https://).
4. Type admin in the Name field, leave the Password field blank, and
select Login.
You can now proceed with configuring your FortiWiFi unit.
Page 5

Page 6
To Connect to the CLI:
You can configure all FortiWiFi configuration options from the CLI
using config commands. The CLI also includes get, show, diagnose,
and execute commands for performing various configuration and
monitoring tasks.
1. Connect the FortiWiFi unit’s console port to the management
computer using the provided console cable.
2. Start a terminal emulation program on the management computer.
Use the following settings:
• Baud Rate: 9600
• Data bits: 8
• Parity: None
• Stop bits: 1
• Flow Control: None
3. Press Enter on your keyboard to connect to the CLI.
4. Type admin in the Name field, leave the Password field blank, and
press Enter.
You can now proceed with configuring your FortiWiFi unit.

# Interface Type Description
1 USB MGMT USB-B USB client port for management.
2 USB USB-A USB server port for USB key, modem, or
management functions.
3 Console RJ-45 Optional serial connection to the Management
Computer. Also gives access to the CLI.
4 DMZ RJ-45 Optional connection to a DMZ network/device
or to other units for High Availability (HA).
5 WAN1 & 2 RJ-45 Gigabit Ethernet Internet connection.
6 Ethernet ports 1 - 5 RJ-45 Gigabit Ethernet 5-port switch connection for
the internal network.
7 Modem RJ-11 PSTN port for connection to telephone
system.
8 Reset Button When enabled (default state), resets the unit to
its factory default settings if pressed during the
first 30 seconds after a reboot.
Power Connection 12V DC, 2.5A
100-240V AC, 1.5A MAX, 50-60Hz adapter
ExpressCard slot The ExpressCard slot (on the front of the
device) adds wireless connectivity (card not
included).
WiFi Dual-band radio supports 802.11a/b/g/n
wireless connectivity.
Supports all popular encryption standards
(open, WEP64/128, WPA, WPA2-personal,
WPA2-enterprise, captive-portal).
Technical Specifications
Page 7
CONSOLE
WAN1WAN2
USBDC+12V 5 1234
USB MGMT DMZ MODEM
1 2 3 4 5 687