Fortinet FortiGate-7000E Series Parts list manual

FortiGate-7060E System Guide
FortiGate-7000E Series

FORTINET DOCUMENT LIBRARY
https://docs.fortinet.com
FORTINET VIDEO GUIDE
https://video.fortinet.com
FORTINET BLOG
https://blog.fortinet.com
CUSTOMER SERVICE & SUPPORT
https://support.fortinet.com
FORTINET TRAINING & CERTIFICATION PROGRAM
https://www.fortinet.com/support-and-training/training.html
NSE INSTITUTE
https://training.fortinet.com
FORTIGUARD CENTER
https://fortiguard.com/
END USER LICENSE AGREEMENT
https://www.fortinet.com/doc/legal/EULA.pdf
FEEDBACK
Email: [e-mail]
January 4, 2021
FortiGate-7060E 6.4.2 System Guide
01-642-411632-20210104

TABLEOFCONTENTS
Change log 6
FortiGate-7060E chassis 7
FortiGate-7060E front panel 7
FIM modules 8
FPM-7620E 8
FPM-7630E 9
FortiGate-7060E back panel 9
Power consumption for different FortiGate-7060E configurations 10
Power consumption calculation with four FPM-7620Es 11
Power consumption calculation with four FPM-7630Es 11
Power consumption calculation with two FPM-7620Es 11
Power consumption calculation with two FPM-7630Es 12
Individual FIM and FPM power consumption 12
Registering your FortiGate-7060E 12
FortiGate-7060E chassis schematic 12
Chassis hardware information 13
Shipping components 14
Optional accessories and replacement parts 14
Physical description of the FortiGate-7060E chassis 15
Cooling fans, cooling air flow, and minimum clearance 16
Cooling air flow and required minimum air flow clearance 17
Optional air filter 18
AC PSUs and supplying AC power to the chassis 18
Hot Swapping an AC PSU 19
DC PSUs and supplying DC power to the chassis 19
Crimping guidelines 21
Connecting a FortiGate-7060E PSU to DC power 21
Hot Swapping a DC PSU 22
Connecting the FortiGate-7060E chassis to ground 23
Turning on FortiGate-7060E chassis power 23
FortiGate-7060E hardware assembly and rack mounting 24
Installing optional accessories 24
Front mounting brackets 24
Left and right cable management brackets 25
Front cable management brackets (FIM-7910E and FIM-7920E only) 25
Power cord clamps 26
Mounting the FortiGate-7060E chassis in a four-post rack 26
Mounting the FortiGate-7060E chassis in a two-post rack 27
Cooling air flow and required minimum air flow clearance 27
Inserting FIMs and FPMs 28
Recommended slot locations for FIMs 29
Getting started with FortiGate-7000 31
Multi VDOM mode 31
FortiGate-7060E System Guide 3
Fortinet Technologies Inc.

Fortinet Technologies Inc.
Confirming startup status 32
Setting up management connections 33
Setting up a single management connection 33
Setting up redundant management connections 34
Adding a password to the admin administrator account 35
Changing data interface network settings 35
Resetting to factory defaults 36
Restarting the FortiGate-7060E 36
Managing individual FortiGate-7000 FIMs and FPMs 37
Special management port numbers 37
HA mode special management port numbers 38
Managing individual FIMs and FPMs from the CLI 39
Connecting to individual FIM and FPM CLIs of the secondary FortiGate-7000 in an
HAconfiguration 39
Firmware upgrades 40
Firmware upgrade basics 40
Verifying that a firmware upgrade is successful 40
Upgrading the firmware running on individual FIMs or FPMs 41
Upgrading FIM firmware 41
Upgrading FPM firmware 42
Installing FIM firmware from the BIOSafter a reboot 43
Installing FPM firmware from the BIOSafter a reboot 45
Synchronizing FIMs and FPMs after upgrading the primary FIM firmware from the BIOS 47
FortiGate-7060E System Management Modules 48
System Management Module failure 49
System Management Module LEDs 49
About SMM alarm levels 51
Using the console ports 52
Connecting to the FortiOS CLI of the FIM in slot 1 53
Connecting to the FortiOS CLI of the FIM in slot 2 53
Connecting to the SMC SDI CLI of the FPMin slot 3 54
Changing the SMM admin account password 54
Connecting to the SMM using an IPMItool 54
FortiGate-7060E chassis slots IPMB addresses 55
Rebooting an FIM or FPM from the SMC SDI CLI 55
Comlog 56
System event log (SEL) 57
Sensor data record (SDR) 57
Common SMM CLI operations 58
Cautions and warnings 63
Environmental specifications 63
Safety 64
Regulatory notices 66
Federal Communication Commission (FCC) – USA 66
FortiGate-7060E System Guide 4

Fortinet Technologies Inc.
Industry Canada Equipment Standard for Digital Equipment (ICES) – Canada 66
European Conformity (CE) - EU 66
Voluntary Control Council for Interference (VCCI) – Japan 67
Product Safety Electrical Appliance & Material (PSE) – Japan 67
Bureau of Standards Metrology and Inspection (BSMI) – Taiwan 67
China 67
FortiGate-7060E System Guide 5

Change log
Date Change description
January 4, 2021 Added more information about using and retaining the FIM and FPM blank panels to
FortiGate-7060E front panel on page 7 and Chassis hardware information on page 13.
Added the FPM-7630E, see FPM-7630E on page 9.
June 22, 2020 Changes to Cooling fans, cooling air flow, and minimum clearance on page 16.
June 22, 2020 Changes to Cooling fans, cooling air flow, and minimum clearance on page 16. Changes to
Power consumption for different FortiGate-7060E configurations on page 10 (waiting for info
from Wei about what to change here). Updated power consumption information in Physical
description of the FortiGate-7060E chassis on page 15.
April 13, 2020 Updated console cable descriptions to reflect that the FortiGate-7060 is now shipped with
USB to RJ-45 RS-232 console cables. Other minor changes.
March 20, 2020 Renamed management module to System Management Module (SMM). Corrections to
Connecting to the SMM using an IPMItool on page 54.
February 24, 2020 Corrections to the 4-post and 2-post rack mount diagrams.
February 21, 2020 Added DC terminal rings and information about included DC cables. See Optional accessories
and replacement parts on page 14 and DC PSUs and supplying DC power to the chassis on
page 19.
October 29, 2019 Misc changes throughout.
October 16, 2019 Restructuring and bug fixing.
FortiGate-7060E 6.4.2 System Guide 6
Fortinet Technologies Inc.

FortiGate-7060E chassis
The FortiGate-7060E is a 8U 19-inch rackmount 6-slot chassis with a 80Gbps fabric and 1Gbps base backplane
designed by Fortinet. The fabric backplane provides network data communication and the base backplane provides
management and synch communication among the chassis slots.
FortiGate-7060E front panel
The chassis is managed by two redundant System Management Modules (SMM). Each SMM includes an Ethernet
connection as well as two switchable console ports that provide console connections to the modules in the chassis slots.
The active SMM controls chassis cooling and power management and provides an interface for managing the modules
installed in the chassis.
FortiGate-7060E front panel, (showing AC PSUs, example module configuration)
ESD
socket
FPM-7630E
slot 3
FPM-7630E
slot 4
FIM-7910E
slots 1 and 2
FPM-7630E
slot 5
FPM-7630E
slot 6
System Management Module 2System Management Module 1
Power
Supply 6
(empty)
Power
Supply 5
(empty)
Power
Supply 1
Power
Supply 4
Power
Supply 2
Power
Supply 3
FortiGate-7060E 6.4.2 System Guide 7
Fortinet Technologies Inc.

FortiGate-7060E chassis Fortinet Technologies Inc.
Do not operate the FortiGate-7060E chassis with open slots on the front or back panel. For
optimum cooling performance and safety, each chassis front panel slot must contain an FIM
or FPM or an FIM or FPM blank panel (also called a dummy card). In addition, all cooling fan
trays, power supplies or power supply slot covers must be installed while the chassis is
operating. The FIM and FPM blank panels are part of the chassis package and all blank
panels should be kept available in case an FIM or FPM is removed from the chassis.
Power is provided to the chassis using four hot swappable 3+1 redundant 100-240 VAC, 50-60 Hz AC or -48V DC power
supply units (PSUs). At least three PSUs (1 to 3) must be connected to power. PSU 4 is a backup PSU. You can add a
5th or 6th PSU for 3+2 and 3+3 redundancy.
The standard configuration of the FortiGate-7060E includes two FIM (interface) modules in chassis slots 1 and 2 and up
to four FPM (processing) modules in chassis slots 3 to 6.
FIM modules
FIM modules are hot swappable interface modules that provide data and management interfaces, base backplane
switching and fabric backplane session-aware load balancing for the chassis. The FIM modules include an integrated
switch fabric and DP2 processors to load balance millions of data sessions over the chassis fabric backplane to FPM
processor modules. The following FIM modules are available:
lThe FIM-7901E includes thirty-two front panel 10GigE SFP+ fabric channel interfaces (A1 to A32). These interfaces
can be connected to 10Gbps networks. These interfaces can also be configured to operate as Gigabit Ethernet
interfaces using SFP transceivers.
lThe FIM-7904E includes eight front panel 40GigE QSFP+ fabric channel interfaces (B1 to B8). These interfaces
can be connected to 40Gbps networks. Using 40GBASE-SR4 multimode QSFP+ transceivers, each QSFP+
interface can also be split into four 10GBASE-SR interfaces and connected to 10Gbps networks.
lThe FIM-7910E includes four front panel 100GigE CFP2 fabric channel interfaces (C1 to C4). These interfaces can
be connected to 100Gbps networks. Using 100GBASE-SR10 multimode CFP2 transceivers, each CFP2 interface
can also be split into ten 10GBASE-SR interfaces and connected to 10Gbps networks.
lThe FIM-7920E includes four front panel 100GigE QSFP28 fabric channel interfaces (C1 to C4). These interfaces
can be connected to 100Gbps networks. Using a 100GBASE-SR4 QSFP28 or 40GBASE-SR4 QSFP+ transceiver,
each QSFP28 interface can also be split into four 10GBASE-SR interfaces and connected to 10Gbps networks.
If you are installing different FIM modules in the FortiGate-7060E chassis, for optimal
configuration you should install the module with the lower model number in slot 1 and the
module with the higher number in slot 2. For example, if your chassis includes a FIM-7901E
and a FIM-7904E, install the FIM-7901E in chassis slot 1 and the FIM-7904E in chassis slot 2.
Also, for example, if your chassis includes a FIM-7904E and a FIM-7920E, install the FIM-
7904E in chassis slot 1 and the FIM-7920E in chassis slot 2. This applies to any combination
of two different interface modules.
FPM-7620E
The FPM-7620E is a hot swappable processor module that provides FortiOS firewalling and security services. FPMs in
the chassis function as workers, processing sessions load balanced to them by the FIMs. FPMs include multiple NP6
network processors and CP9 content processors to accelerate traffic.
FortiGate-7060E 6.4.2 System Guide 8

FortiGate-7060E chassis Fortinet Technologies Inc.
FPM-7630E
The FPM-7630E is a hot swappable processor module that provides FortiOS firewalling and security services. FPMs in
the chassis function as workers, processing sessions load balanced to them by the FIMs. FPMs include multiple NP6
network processors and CP9 content processors to accelerate traffic.
The FPM-7630E processor module is an update of the FPM-7620E processor module with the
same architecture but a newer CPU configuration. You can mix FPM-7630Es and FPM-
7620Es in the same FortiGate-7000 chassis. In an HA configuration, both chassis in the HA
cluster must have the same FPM modules in the same slots.
FortiGate-7060E back panel
The FortiGate-7060E back panel provides access to three hot swappable cooling fan trays and the chassis ground
connector that must be connected to ground.
FortiGate-7060E 6.4.2 System Guide 9

FortiGate-7060E chassis Fortinet Technologies Inc.
FortiGate-7060E back panel
Fan Tray 1Fan Tray 2Fan Tray 3
Chassis
Ground
Connector
Power consumption for different FortiGate-7060E configurations
The tables in this section provide information about how to calculate average and maximum power consumption for a
FortiGate-7060E system with four and with two FPMs two FIM-7901Es.
This section also includes a table showing the average and maximum power consumption for all FIM and FPM
modules.
FortiGate-7060E 6.4.2 System Guide 10

FortiGate-7060E chassis Fortinet Technologies Inc.
Power consumption calculation with four FPM-7620Es
Module Average power
consumption (W)
Max power
consumption (W)
Number of
modules
Total
average
power (W)
Max power
(W)
FPM-7620E 320 410 4 1280 1640
FIM-7901E 260 450 2 520 900
Fan trays and
SMMs
530 737 N/A 530 737
Totals 2330 3277
Power consumption calculation with four FPM-7630Es
Module Average power
consumption (W)
Max power
consumption (W)
Number of
modules
Total
average
power (W)
Max power
(W)
FPM-7630E 340 440 4 1360 1760
FIM-7901E 260 450 2 520 900
Fan trays and
SMMs
530 737 N/A 530 737
Totals 2410 3397
Power consumption calculation with two FPM-7620Es
Module Average power
consumption (W)
Max power
consumption (W)
Number of
modules
Total
average
power (W)
Max power
(W)
FPM-7620E 320 410 2 640 820
FIM-7901E 260 450 2 520 900
Fan trays and
SMMs
530 737 N/A 530 737
Totals 1690 2457
FortiGate-7060E 6.4.2 System Guide 11

FortiGate-7060E chassis Fortinet Technologies Inc.
Power consumption calculation with two FPM-7630Es
Module Average power
consumption (W)
Max power
consumption (W)
Number of
modules
Total
average
power (W)
Max power
(W)
FPM-7630E 340 440 2 680 880
FIM-7901E 260 450 2 520 900
Fan trays and
SMMs
530 737 N/A 530 737
Totals 1730 2517
Individual FIM and FPM power consumption
Module Power consumption (average / maximum) (W)
FPM-7620E 320 / 410
FPM-7630E 340 / 440
FIM-7901E 260 / 450
FIM-7904E 260 / 450
FIM-7910E 260 / 450
FIM-7920E 410 / 460
Registering your FortiGate-7060E
FortiGate-7000 series products are registered according to the chassis serial number. You need to register your chassis
to receive Fortinet customer services such as product updates and customer support. You must also register your
product for FortiGuard services. Register your product by visiting https://support.fortinet.com. To register, enter your
contact information and the serial numbers of the Fortinet products that you or your organization have purchased.
FortiGate-7060E chassis schematic
The FortiGate-7060E chassis schematic below shows the communication channels between chassis components
including the SMMs (MGMT), the FIMs (called FIM1 and FIM2) and the FPMs (FPM3, FPM4, FPM5, and FPM6).
FortiGate-7060E 6.4.2 System Guide 12

FortiGate-7060E chassis Fortinet Technologies Inc.
IPMB
SERIAL
IPMB
SERIAL
IPMB
SERIAL
IPMB
SERIAL
NP6
CP9
NP6
CP9 SMC SDI
ISF
DP2
ISF
DP2
IPMB
SERIAL
1G
SMC SDISMC SDI
MGMT2 (active by default, IPMB 0x20)MGMT1 (inactive by default, IPMB 0x22)
FPM
FIM
FIM
FPM
FPM3 IPMB 0x86
IPMB
SERIAL
NP6
CP9 SMC SDI
FPM FPM5 IPMB 0x8A
FPM4 IPMB 0x88
FIM1 IPMB 0x82
FIM2 IPMB 0x84
PMB
0
x
8
2
SMC SDI
PMB 0x84
SMC SDI
PMB 0x88
SMC SDI
IPMB
SERIAL
NP6
CP9 FPM FPM6 IPMB 0x8C
PMB 0x8C
SMC SDI
Data
Interfaces
MGMT
1-4 M1 M2
Data
Interfaces
MGMT
1-4 M1 M2
Fabric Backplane
1G
1G
1G
1G
1G
1G
80G
80G
80G
80G
80G
80G
80G
80G
80G
80G
80G
80G
80G
80G
80G
80G
40G
40G
Base Backplane
By default, MGMT2 is the active SMM and MGMT1 is inactive. The active SMM always has the Intelligent Platform
Management Bus (IPMB) address 0x20 and the inactive SMM always has the IPMB address 0x22.
The active SMM communicates with all modules in the chassis over the base backplane. Each module, including the
SMMs has a Shelf Management Controller (SMC). These SMCs support IPMB communication between the active SMM
and the FIM and FPMs for storing and sharing sensor data that the SMM uses to control chassis cooling and power
distribution. The base backplane also supports serial communications to allow console access from the SMM to all
modules, and 1Gbps Ethernet communication for management and heartbeat communication betweenmodules.
FIM1 and FIM2 (IPMB addresses 0x82 and 0x84) are the FIMs in slots 1 and 2. The interfaces of these modules
connect the chassis to data networks and can be used for Ethernet management access to chassis components. The
FIMs include DP2 processors that distribute sessions over the Integrated Switch Fabric (ISF) to the NP6 processors in
the FPMs. Data sessions are communicated to the FPMs over the 80Gbps chassis fabric backplane.
FPM03, FPM04, FPM05, and FPM06 (IPMB addresses 0x86, 0x88, 0x8A, and 0x8C) are the FPM processor modules in
slots 3 to 6. These worker modules process sessions distributed to them by the FIMs. FPMs include NP6 processors to
offload sessions from the FPM CPU and CP9 processors that accelerate content processing.
Chassis hardware information
This section introduces FortiGate-7060E hardware components and accessories including power requirements and
FIMand FPM modules that can be installed in the chassis.
FortiGate-7060E 6.4.2 System Guide 13

FortiGate-7060E chassis Fortinet Technologies Inc.
Shipping components
The FortiGate-7060E chassis ships pre-assembled with the following components:
lThe 8U FortiGate-7060E chassis.
lTwo FIM modules.
lUp to four FPM modules.
lTwo System Management Modules (SMMs) in the front of the chassis. (SMMs are not field replacable. If a SMM
fails, you must RMA the chassis. The chassis will continue to operate with one or no operating SMM.)
lFour Power Supply Units (PSUs) installed in the front of the chassis.
lThree cooling fan trays installed in the back of the chassis.
lOne protective front panel installed in the chassis to protect internal chassis components. This panel must be
removed before installing FIM and FPM modules.
lSix FIM and FPM blank panels that can be installed in empty chassis slots. The blank panels are part of the chassis
package and all blank panels should be kept available in case an FIMor FPM needs to be removed from the
chassis.
lFour power cords with C15 power connectors.
lSix power cord management clamps.
lOne set of 4-post rack mounting components.
lOne set of 2-post rack mounting components.
lOne pair of cable management side brackets.
lTwo front mounting brackets.
lTwenty-four M4x6 flat-head screws.
lSix M4x8 large head pan-head screws.
lSix rubber feet.
lTwo USB to RJ-45 RS-232 console cables.
lOne RJ-45 Ethernet cable.
Optional accessories and replacement parts
The following optional accessories can be ordered separately:
SKU Description
FG-7060E-FAN FortiGate-7060E fan tray.
FG-7060E-PS-AC 1500W AC power supply units (PSUs) for the FortiGate-7060E.
FG-7060E-PS-DC 1500W DC power supply units (PSUs) for the FortiGate-7060E.
FG-7060E-CHASSIS FortiGate-7060E chassis including 2x SMM, 3x fan trays, and 4x AC or DC PSUs.
You can also order the following:
lAdditional FIM and FPM modules
lTransceivers
lDC PSUs (Each PSU ships with a set of two 8 AWG DC power cables and six extra DC terminal rings. The cables
are 3 meters (9.84 ft.) long. You can use the DC terminal rings to make custom DC cables.)
lAir Filter kit
lFPM and FIM single slot cover trays to be installed in empty chassis slots
FortiGate-7060E 6.4.2 System Guide 14

FortiGate-7060E chassis Fortinet Technologies Inc.
The following optional accessories can be ordered separately:
lAdditional FIM and FPM modules
lTransceivers
lDC PSUs
lAdditional AC PSUs
lAdditional FAN trays
lAir Filter kit
lFPM and FIM blank panels to be installed in empty chassis slots
Physical description of the FortiGate-7060E chassis
The FortiGate-7060E chassis is a 8U chassis that can be installed in a standard 19-inch rack. The following table
describes the physical characteristics of the FortiGate-7060E chassis.
Dimensions (H x W x D) 14.0 x 17.3 x 25.6 in (352.7 x 440 x 650 mm)
Chassis weight completely assembled with
FIM and FPM modules installed
207.2 lbs (94.1 kg)
Operating Temperature 32 to 104°F (0 to 40°C)
Storage Temperature -31 to 158°F (-35 to 70°C)
Relative Humidity 10% to 90% non-condensing
Noise Level 63db
AC Input Current and Voltage Range 10-12 A, 100 to 240 VAC (50 to 60 Hz)
DC Input Rating Average: 12.5A@48V for eachPSU, max 44A
Power Support Rating max. 3277W
Supplied Power Supply Units (PSUs) 4 (for 3+1 redundancy)
Max Power Supply Units (PSUs) 6 (for 3+3 redundancy)
Max Power Consumption 3277W
Average Power Consumption 2330W
Max Power Consumption 3360W
Average Power Consumption 2380W
Heat Dissipation 11799KJ/hr (11184BTU/hr)
Heat Dissipation 11464BTU/h
FortiGate-7060E 6.4.2 System Guide 15

FortiGate-7060E chassis Fortinet Technologies Inc.
Cooling fans, cooling air flow, and minimum clearance
The FortiGate-7060E chassis contains three hot swappable cooling fan trays installed in the back of the chassis. Each
fan tray includes two fans that operate together. When the fan tray LED is green, both fans are operating normally. If
the LED turns red or goes off, one or both of the fans is not working and the fan tray should be replaced.
During normal chassis operation, all three fan trays are active and the fan speed is controlled by the active SMM. If a
single fan tray fails, the SMMsends a warning message and the SMM front panel fan LEDs indicate that a fan tray has
failed. The SMM maintains sufficient cooling by running the still operating fans at full speed to make up the airflow loss
caused by the failed fan tray. The failed fan tray should be replaced as soon as possible.
If a second fan tray fails, the chassis can continue to operate but the chassis may experience high temperature
warnings. Maintaining a lower ambient temperature can reduce the chance for overheating.
Fan trays are hot swappable. You can replace a failed fan tray while the chassis is operating. To replace a fan tray,
unscrew the four retention screws and use the handles to pull the fan tray out of the chassis.
Install a replacement fan tray by sliding it into place in the empty slot and tightening the retention screws. As you slide
the new fan into place it will power up and the fan tray LED will light.
The other fan trays will continue to operate and cool the chassis as a fan tray is being removed and replaced. However
an open fan tray slot will result in less air flow through the chassis so do not delay installing the replacement fan tray.
The active FortiGate-7060E System Management Module (SMM) monitors the internal temperature of the chassis and
adjusts the operating speed of the cooling fans as required. When the chassis is first powered on, all cooling fans run at
full speed. Once the active SMM is up and running, it reduces cooling fan speeds to maintain an optimum temperature
in the chassis. If an SMM is not available or is not operating correctly, the fans always operate at full speed.
During normal operation, all fan trays are active. If cooling requirements increase, the fan speed will increase.
FortiGate-7060E 6.4.2 System Guide 16

FortiGate-7060E chassis Fortinet Technologies Inc.
Cooling Fan Tray
Retention
Screw
Fan
LED
Retention
Screw
Retention
Screw
Retention
Screw
Outlet
Grill
Outlet
Grill
Cooling air flow and required minimum air flow clearance
When installing the chassis, make sure there is enough clearance for effective cooling air flow.The following diagram
shows the cooling air flow through the chassis and the locations of fan trays. Make sure the cooling air intake and warm
air exhaust openings are not blocked by cables or rack construction because this could result in cooling performance
reduction and possible overheating and component damage.
FortiGate-7060E 6.4.2 System Guide 17

FortiGate-7060E chassis Fortinet Technologies Inc.
FortiGate-7060E cooling air flow and minimum air flow clearance
Cool air
Intake
Left and Right
Side Cool Air
Intakes
50 mm
Clearance
(Optional)
Front
FortiGate-7060E chassis (side View)
Fan
Trays
100 mm
650 mm
Warm Air
Exhaust
Back
100 mm
Most cool air enters the chassis through the chassis front panel and all warm air exhausts out the back. For optimal
cooling allow 100 mm of clearance at the front and back of the chassis and 50 mm of clearance at the sides. Under
these conditions 80% of cooling air comes from the front panel air intake and 20% from the left and right side panels
and 100% exits out the back. Side clearance is optional and chassis cooling will be sufficient if no side clearance is
available.
Optional air filter
You can purchase an optional NEBScompliant air filter kit that includes a front filter that fits over the front of the chassis
and two filters for the side cool air intakes. These filters are not required for normal operation but can be added if you
require air filtration.
The air filters should be inspected regularly. If dirty or damaged, the filters should be disposed of and replaced. The air
filters can be fragile and should be handled carefully.
AC PSUs and supplying AC power to the chassis
The AC version of the FortiGate-7060E chassis front panel includes four hot swappable AC PSUs. At least three PSUs
(1, 2, and 3) must be connected to power. PSUs 4 to 6 provide 3+1 , 3+2, and 3+3 redundancy. See FortiGate-7060E
front panel on page 7 for locations of the PSUs.
All PSUs should be connected to AC power. To improve redundancy you can connect each PSU to a separate power
source.
FortiGate-7060E 6.4.2 System Guide 18

FortiGate-7060E chassis Fortinet Technologies Inc.
Use a C15 Power cable, supplied with the chassis, to connect power to each PSU C16 power connector. C15/C16 power
connectors are used for high temperature environments and are rated up to 120°C.
AC PSU showing C16 power connector
Latch
PSU
LED
C16
Power
Connector
The PSU LED indicates whether the PSUis operating correctly and connected to power. If this LEDis not lit, check to
make sure the PSU is connected to power. If the power connection is good then the PSU has failed and should be
replaced.
Hot Swapping an AC PSU
Follow these steps to safely hot swap an AC PSU.
You can hot swap a PSU without powering down the FortiGate-7060E as long as three PSUs
are connected to power and operating normally. If you need to hot swap one of three
operating PSUs, you must power down the chassis first.
1. Attach an ESD wrist strap to your wrist and to an ESD socket or to a bare metal surface on the chassis or frame.
2. Turn off the power being supplied to the power supply and disconnect the power cord.
3. Press the latch towards the handle until the PSU is detached then pull it out of the chassis.
4. Insert a replacement PSU into the chassis and slide it in until it locks into place.
5. Connect the PSUpower terminals as described above.
6. Turn on power to the PSU.
7. Verify that the PSU status LED is solid green meaning that the PSU is powered up and operating normally.
DC PSUs and supplying DC power to the chassis
The DC version of the FortiGate-7060E chassis front panel comes with four hot swappable 48-72V to 12V 125A DC
PSUs. Each PSU has a Internal 60A/170VDC fast blow fuse on the DC line input.
At least three PSUs (power supplies 1, 2, and 3) must be connected to power. The fourth power supply is a backup
power supply and provides 3+1 redundancy. You can add a fifth power supply to provide a second backup power supply
and 3+2 redundancy. You can add a 6th power supply to provide a third backup power supply and 3+3 redundancy. See
FortiGate-7060E 6.4.2 System Guide 19

FortiGate-7060E chassis Fortinet Technologies Inc.
FortiGate-7060E front panel on page 7 for locations of the PSUs. The diagram shows AC PSUs, with a DC version of the
chassis the AC PSUs are replaced with DC PSUs.
Each PSU is designed to be installed in a Telecom data center or similar location that has available -48VDC power fed
from a listed 40A circuit breaker. To improve redundancy you can connect each power supply to a separate power
circuit.
DC power cables are intended to be used only for in-rack wiring, must be routed away from sharp edges, and must be
adequately fixed to prevent excessive strain on the wires and terminals. Make sure DC terminal rings are securely and
safely fastened to the PSU terminals.
DC PSU (power connector cover removed)
Latch
LED
+ (Red)
Power
Connector
- (Black)
Power
Connector
DC terminals accept UL approved ring terminals for 8/M4 stud with ext ring diameter < 9.8 mm. DC cables must be a
minimum of 8 AWG. Each PSU ships with a set of two 8 AWG DC power cables and six extra DC terminal rings. The
cables are 3 meters (9.84 ft.) long. You can use the DC terminal rings to make custom DC cables.
PSU Power ratings
Max Inrush Current 50A
Max Inrush Current Duration 200ms
Input Voltage -40V to -72V
Input Current Average: 12.5A@48V for each PSU, Max: 44A
PSU LED States
State Description
Off DC power not connected.
Flashing Green The PSUis in standby mode, not supplying power to the chassis.
Green Normal Operation with DC power connected.
Amber Input voltage outside of normal operating range, PSU fan not operating, or output
FortiGate-7060E 6.4.2 System Guide 20