Foundations 100-SSC-R User manual

SI258R-H
• Failure to follow these warnings and the installation instructions could result in serious injury
or death.
• Read all instructions before installing diaper changing station. Keep these instructions. DO NOT
discard.
WARNING
AVERTISSEMENT
ADVERTENCIA
Model 100-SSC-R
Clad Stainless Steel Changing Station
Installation Instructions
(Recessed Mount)
IMPORTANT: RETAIN FOR FUTURE
REFERENCE. READ CAREFULLY

A.D.A. Compliance:
306.3 Knee Clearance
307.2 Maximum Protruding Objects
308.2 Forward Reach
308.3 Side Reach
309.4 Operation
902.3 Work Surface
Compliant when properly installed.
ADULT INSTALLATION REQUIRED.
TOOLS REQUIRED:
Level(A)
Measuring tape (B)
Power drill with 3/16” masonry bit (C)
Power screwdriver with bull nose phillips bit (D)
Truss head spanner bit (E)
•READ ALL INSTRUCTIONS BEFORE ASSEMBLY OF DIAPER CHANGING STATION.
•Unpack carton and identify all parts.
INSTALLATION INSTRUCTIONS
1
• This changer has six (6) recess mounting holes.
• The diaper changing station is no stronger than the anchors or walls to which they are attached and, therefore,
MUST be firmly secured in order to support the weight they are intended to support. Contact an architect or building
contractor if any questions.
WARNING
21-3/8”
542 mm
13-1/8”
(333 mm)
34-3/4”
(883 mm)
(Door)
3” x 1/4” Wood Screws
Parts Description Quantity
Hardware for recessed installation:
3” x 1/4” Wood Screws 6
3/4” Finishing Washer
1
PARTS LIST
Door / wall plate to be
mounted on outside of
restroom door.
AB
D
C
E
3/4” Finishing Washer
Door / Wall Plate
6

2
Recommended Blocking:
Wood double stud blocking is necessary. Contact an architect and
with building codes (Fig. a.).
For A. D. A. compliance, top of lower double stud should be 28” (71 cm)
1. Slide changer into blocking area and mark mounting hole location
on blocking studs.
HINT: This may require 2 additional people to help hold changer
in position while you are marking the locations.
2. Use a power drill with a 3/16” bit and drill six (6) pilot holes in
the blocking studs.
3.
NOTE: If lower holes are inaccessible, remove plastic unit from steel
back by removing the 4 Truss Head Spanner Screws c). Once
steel back is attached to blocking, reconnect plastic wall to steel
back using the same spanner screws.
4. Align holes in changer with drilled holes and secure
using the wood screws and finish washers. Wood screws have been
provided and are for wood only (Fig. b).
NOTE: It is installers responsibility to provide
correct fastereners for other substrates.
5. Ensure all six (6) screws are tight.
OPERATION:
Rotate base downward. Place infant on top of the changing surface. Use restraint
system as described below. After child has been changed, remove restraint system
and rotate base back up against the wall.
USE OF RESTRAINT SYSTEM:
Place child so restraint strap is located at abdomen. Rotate top of buckle upward and insert strap
in buckle. Pull strap through buckle until snug against infant. Rotate top of buckle downward to lock
the strap into place. Reverse steps to loosen strap.
MAINTENANCE AND CLEANING:
Check all hardware and components monthly or as required to ensure hardware is tight and there
are no missing or damaged components. Take unit out of service if any component is missing or
damaged and contact customer service to order replacement parts. Do not substitute parts.
For replacement parts, contact customer service at 1-877-716-2757.
Clean by using a damp cloth with mild soap or mild multi-purpose cleaner. Do not use any strong
chemical cleaners or cleaning agents that may be hazardous to children.
INSTALLATION
Fig. b
Recess Mounting
Holes Typ. 6
Fig. a
Fig. c
Truss Head
Spanner Screws
• Avoid serious injury from falling or sliding out. Always use restraint system.
• Adding excessive weight such as parcels, packages, or accessories to the unit or to the bag hooks that exceed the total
weight limit of 50 pounds (22.7 kg) may cause the unit to be unstable or may cause a hazardous unstable
condition to
exist.
• DO NOT add a changing pad to this product.
• DO NOT use this product when any part is broken, torn or missing.
• Be aware of the risk of open and other sources of strong heat, such as electric bar gas etc. in the
near
vicinity ofthe changing unit.
•
WARNING
• DO NOT leave child unattended.
Intended for children up to 15 kg (EU) and up to 50 pounds (22.7kg) (US).
Finishing Washer Typ.6
Wood Screw Typ.6
from the floor.
TOP
VIEW
FRONT
VIEW
35 5/8" (905 mm)
Rough-in
Double Stud
Double Stud
Double Stud
Double Stud
3 7/8"
(98.4 mm)
1"
(25.4 mm)
19 5/8"
(499 mm)
Rough-in
35 5/8"
(905 mm)
28"
(71 cm)