FourStarGroup 11211722V User manual

11211722V
COMPUTER DESK
V

2
1 LONG TUBE (2 PCS)
2 SHORT TUBE (12 PCS)
3 LEG (4 PCS)
4 INSERT CAP (4 PCS)
5 DRAWER SLIDE (1 SET)
6 10mm SCREW ( 9 PCS)
7 32mm SCREW (4 PCS)
8 L-BRACKET (1 PCS)
A TOP PANEL (1 PC)
B BOTTOM PANEL (1 PC)
C KEYBOARD PANEL (1 PC)
D L&R SLIDE PANEL (2 PCS)
E APRON (2 PCS)
F L&R CROSSBAR (2 PCS)
G BOTTOM CROSSBAR (1 PC)
5B
5A (2 PCS)
(2 PCS)
A
B
C
D
E
E
FF
G
D
BEFORE YOU BEGIN, PLEASE FOLLOW ASSEMBLY INSTRUCTIONS
CAREFULLY. FOLLOW THEM STEP BY STEP.
PARTS AND HARDWARE

3
PHILLIPS
SCREWDRIVER
RUBBER MALLET
BEFORE YOU BEGIN, PLEASE READ ASSEMBLY
INSTRUCTIONS CAREFULLY. FOLLOW THEM STEP BY STEP.
ASSEMBLY TOOLS REQUIRED :
CAUTION :
1. ADULT SUPERVISION IS REQUIRED DUE TO SMALL PARTS.
CARE SHOULD BE TAKEN IN THE UNPACKING AND
ASSEMBLY OF THE PRODUCT.
2. ASSEMBLE ON SOFT SURFACES TO PREVENT DAMAGE TO
THE PRODUCT FINISH.
3. MAKE SURE ALL PARTS ARE INCLUDED BEFORE ASSEMBLY.

4
STEP 1.
ATTACH THE INSERT CAPS ( 4 ) TO THE TOP PANEL ( A ) USING 4
SHORT TUBES ( 2 ) AS SHOWING.
4
4
4
4
A
2
2
2
2
2
4
UNFINISHED
SURFACE

5
STEP 2.
ATTACH 10" DRAWER SLIDERS ( 5A ) TO L & R SLIDER PANEL ( D )
USING 1/2" SCREWS ( 6 ) AS SHOWN.
UNFINISHED
EDGE
6
6
6
5A
UNFINISHED
EDGE
5A
D
D
6

6
STEP 3.
ATTACH F & B APRON PANEL ( C ) TO ASSEMBLED L & R SLIDE PANEL
( D ) FROM STEP 2 USING 32mm SCREWS ( 7 ) AS SHOWN.
D
77
D
UNFINISHED SURFACE E
77
UNFINISHED EDGE
E
UNFINISHED SURFACE

7
STEP 4.
USING THE ASSEMBLED PARTS FROM STEP 1 AND STEP 3 ATTACH
SHORT TUBES ( 2 ) AS SHOWN.
D
E
A
P5
D
2
2
2
2
E
UNFINISHED
SURFACE
UNFINISHED
SURFACE

8
STEP 5.
ATTACH L & R SIDE PANEL ( F ) AND BOTTOM CROSSBAR ( G ) TO
ASSEMBLED FROM STEP 4 USING LONG TUBES ( 1 ) AND SHORT
TUBES ( 2 ) AS SHOWING.
F
2
2
2
2
F
1
1
UNFINISHED
SURFACE
UNFINISHED
SURFACE
UNFINISHED
SURFACE

9
STEP 6.
ATTACH BOTTOM PANEL ( P2 ) TO ASSEMBLED FROM STEP 5 USING
LEGS ( 3 ) AS SHOWING.
B
3
3
33
UNFINISHED
SURFACE

10
STEP 7.
ATTACH 10" DRAWER SLIDERS (5B) AND TO KEYBOARD PANEL (C)
USING 1/2" SCREWS (6) AS SHOWN.
5B
6
FINISH EDGING
SURFACE
UNFINISH
SURFACE C

ATTACH L-BRACKET (8) TO KEYBOARD PANEL (C) USING 1/2"
SCREWS (6) AS SHOWN.
STEP 8.
11
C
6
8
FINISH SURFACE

Do you have any questions ? Missing small parts or hardware ?
If you need assistance with the assembly of your COMPUTER
DESK please e-mail our Customer Service
Department at:
[e-mail]
or call us at [phone]
or [phone]
Please include the following information in your email:
ï Where item was purchased
ï Item, model, style or SKU number listed on instructions
or box
ï Part number, description of the part and quantity needed
This information will help us get the proper part to you faster
12
STEP 9.
SLIDE THE KEYBOARD PANEL ( C ) TO THE ASSEMBLED COMPUTER
DESK AS SHOWN.
150 lbs.
70 lbs.
C
This unit is intended for use only with the
products and maximum weights indicated. Use
with other products or products heavier than the
maximum weights indicated may result in
instability causing possible injury. Furniture can
tip over or break if improperly moved. Have a
friend help to lift and carry the unit to it's new
location.