Foxun SX-SPH2-100 User manual

Quick Start Guide
Features
8
•Incorporates HD Base-T technology
•Distributes 1 HDMI source to 2 HDMI Displays simultaneously.
•Full HD support: 1080p@60Hz@48 b/pixels, support 3D and 4Kx2K
•Extends HDMI and IR up to 328 feet (100 meters) using one CAT5e (or better) cable
•With Infrared control signal passing through function.
•Supports high bit-rate audio formats (Dolby True-HD / DTS Master Audio )
•100BaseT Ethernet &RS-232 Pass-Through(Output1)
•HDCP compliant.
•CEC Pass-Through
•DC 5V power supply
Packing contents
1) Main Unit: 1x2 HDBaseT Splitter
2) Power supply DC 5V 3A
3) IR-TX cable x 2PCS
4) IR-RX cable x 2 PCS
5) M3x5 Screw x 6PCS
6) Operating Instructions
7) Mounting ear
Dimensional drawing
TABLE OF CONTENTS
Package Contents
Dimensional drawing
Specications
Panel Descriptions
Connecting and Operating
Typical Application
Maintenance
Product Service
Warranty
2-PORT HDBaseT SPLITTER
-5 to +35 C(+23 to +95 F)
5 to 90%RH (No Condensation)
300MHz/9Gbps
Up to 1080p@60Hz@48 b/pixels, support 3D ,4K
HDMI receptacle.
RJ45
Power connector terminal
Power DC receptacle
IR Blaster
D-Type 9pin plug
1080P 328FT/100m over single CAT5E/6 cable
110-240V/ 5VDC 3A power supply
10Watts
Cold-Rolled (Cold Rolled) Steel
W200xH116xT30mm
630g
30mm
200mm
116mm

Front Panel
Rear Panel
Power ON/OFF
Status indicator lamp:The LED will illuminate when the HDMI equipment is connected.
Power indicator lamp:The LED will illuminate when the power is on.
Reset key
Power input port RS232 port
1 2
3
4
Ethernet port Output1 port ( Ethernet,RS232 &IR pass-though)
Output2 port ( IR pass-though)
1 2
34
56
HDMI input port
Connecting and operating
1) Connect the HDMI input sources into HDBaseT splitter.
2) Connect HDMI receiver over Cat5e/Cat6 cables to both the Cat5e/6 port of HDBaseT Splitter
and Cat5e/6 port of Receiver,The RJ45 connections must follow EIA-TIA 568b standards.
3) Connect the HDMI output from the Receiver(RX) into the display HDMI input.
4) Connect the IR TX receiving cables into splitter IR TX port on the back panel and afx the
emitter onto the source IR windows. .
5) Connect IR-RX cable into IR-RX port on the receiver and afx the IR receiver in direct line of site
with the handheld remote control.It is recommended to afx the receiver on the display frame
/bezel or the display stand.
Note：Do not affix the emitter until the placement is tested.
6) Power up all units, the splitter,Receiver, sources and displays.
RS-232 pin assignment
HDBaseT Splitter
PIN Assignment
1 NC
2 TX
3 RX
4 NC
5 GND
6 NC
7 NC
8 NC
9 NC
7) To get on the ethernet,pls connect as below steps:
1.Connect ethernet cable into ethernet port on HDBaseT splitter.
2.Connect ethernet cable with TV and ethernet extender receiver
Note:1.The ethernet function is designed for ethernet compatible receiver units only.
2.Only output1 with ethernet function.
8) Copy EDID function
Copy the EDID of the sink which connected the OUTPUT1,it is suggested to put lowest or
the most compatible display specication on output1.
For example:
One SDTV(480p) ,one HDTV(1080p), in order to make the 2 TV work, you need to put the
SDTV is connected to the output 1 .
HDMI cable
Output1
Ethernet cable
Smart TV HDTV
HDMI cable
HDMI cable
Computer RS232 port
PIN Assignment
1 NC
2 RX
3 TX
4 NC
5 GND
6 NC
7 NC
8 NC
9 NC
RS232 cable
Router
Internet