FRAM Moonstone ACF-MS12WIFI-GD User manual

ACF-MS12WIFI-GD
ACF-MS12WIFI-GY
Remote controller user manual

Please read the instructions carefully and keep the manual for future information.
This manual is designed to give all necessary instructions concerning installation, use and maintenance of the
unit. In order to operate the unit correctly and safely, please read this instruction manual carefully before
installation and use.
Not sure what a function does?
Refer to the How to Use Basic Functions and How to Use Advanced Functions sections of this manual for a
detailed description of how to use your air conditioner.
Special note
•Button designs on your unit may differ slightly from the example shown.
•If the indoor unit does not have a particular function, pressing that function’s button on the remote
control will have no effect.
•When there are wide differences between “Remote controller Manual” and “USER’S MANUAL” on
function description, the description of “USER’S MANUAL” shall prevail.
Thank you for choosing this Fram product!
1. INTRODUCTION
2. QUICK START GUIDE
FIT BATTERIES
SELECT MODE
SELECT TEMPERATURE
SELECT FAN SPEED
PRESS POWER BUTTON
POINT REMOTE TOWARD UNIT

Inserting and replacing batteries
Your air conditioning unit may come with two batteries (some units). Put the batteries in the remote control
before use.
1. Slide the back cover from the remote control downward, exposing the battery compartment.
2. Insert the batteries, paying attention to match up the (+) and (-) ends of the batteries with the symbols
inside the battery compartment.
3. Slide the battery cover back into place.
Battery notes
For optimum product performance:
•Do not mix old and new batteries, or batteries of different types.
•Do not leave batteries in the remote control if you don’t plan on using the device for more than 2
months.
Battery disposal
Do not dispose of batteries as unsorted municipal waste. Refer to local laws for proper disposal of batteries.
Tips for using remote control
•The remote control must be used within 8 meters of the unit. The unit will beep when remote signal
is received.
•Curtains, other materials and direct sunlight can interfere with the infrared signal receiver.
•Remove batteries if the remote will not be used more than 2 months.
•Prevent any liquid from falling into the remote control.
Notes for using remote control
The device could comply with the local national regulations.
1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
3. HANDLING THE REMOTE CONTROLLER

determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
•Consult the dealer or an experienced radio/TV technician for help.
•Changes or modifications not approved by the party responsible for compliance could void user’s
authority to operate the equipment.

Before you begin using your new air conditioner, make sure to familiarize yourself with its remote control.
The following is a brief introduction to the remote control itself. For instructions on how to operate your air
conditioner, refer to the How to Use Basic Functions section of this manual.
4. BUTTONS AND FUNCTIONS
ON/OFF
Turns the unit on or off.
TEMP ˄
Increases temperature in 0.5 °C (1 °F)
increments. Max. temperature is 30 °C
(86 °F).
NOTE: Pressing together ˅ and ˄ buttons
at the same time for 3 seconds will
alternate the temperature display
between °C and °F.
SET
Scrolls through operation functions as
follows:
Active clean ( ) → Fresh ( ) → Sleep
()→ Follow me ( ) → AP mode ( )
→ Active clean...
The selected symbol will flash on the
display area. Press OK button to
confirm.
TEMP ˅
Decreases temperature in 0.5 °C (1 °F)
increments. Min. temperature is 16 °C
(60 °F).
FAN SPEED
Selects fan speeds in the following order:
AU → 20% → 40% → 60% → 80% →
100%.
Press the TEMP ˄ or ˅ button to
increase/decrease the fan speed in 1%
increments.
SWING
Starts and stops the horizontal louver
movement. Hold down for 2 seconds to
initiate vertical louver auto swing feature.
MODE
Scrolls through operation modes as follows:
AUTO → COOL → DRY → HEAT → FAN.
NOTE: HEAT mode is not supported by the
cooling only appliance.
Breeze Away function
Used to select wind flow away from people
feature.
OK
Used to confirm the selected functions.
TIMER
Set timer to turn unit on or off.
ECO/GEAR
Press this button to enter the energy efficient mode
in a sequence of following:
ECO→ GEAR (75%) → GEAR (50%) → Previous
setting mode → ECO …
Cascade
This feature enables the whole room to be cool
quickly and evenly.
LED
Turns indoor unit’s LED display and air
conditioner buzzer on and off (model
dependent), which creates a comfortable and
quiet environment.
Turbo
Enables unit to reach preset temperature in the
shortest possible time.

Remote screen indicators
Information are displayed when the remote controller is power up.
Note:
All indicators shown in the figure are for the purpose of clear presentation. But during the actual operation,
only the relative function signs are shown on the display window.
Active Clean feature display
Fresh feature display
Sleep mode display
Follow me feature display
Wireless control feature display
Not applicable for this unit
Low battery detection display (if it flashes)
Breeze away people (downward)
Breeze away people (upward)
Transmission indicator
Lights up when remote sends signal to
indoor unit.
TIMER ON display
TIMER OFF display
Silence feature
display
FAN SPEED display
Displays selected fan speed.
Silence
LOW
MED
HIGH
AUTO
Upward cascade display.
Downward cascade display.
Horizontal louver swing display.
Vertical louver auto swing
display.
Turbo mode display.
MODE display
Displays the current mode, including:
This fan speed cannot be adjusted in
AUTO or DRY modes.
ECO display
Displays when ECO feature is activated.
GEAR display
Displays when GEAR feature is
activated.
LOCK display
Displays when LOCK feature is
activated.
Temperature/Timer Fan Speed display
Displays the set temperature by default,
or fan speed or timer setting when using
TIMER ON/OFF functions.
- Temperature range:
16-30°C/60-86°F
- Timer setting range:
0-24 hours
-Fan speed setting range:
AU-100%
This display is blank when operating in
FAN mode.

Attention! Before operation, please ensure the unit is plugged in and power is available.
Setting temperature
The operating temperature range for units is 16-30°C (60-86°F). You can increase or decrease the set
temperature in 0.5°C (1°F) increments.
AUTO mode
In AUTO mode, the unit will automatically select
the COOL, FAN, or HEAT operation based on the
set temperature.
1. Press the MODE button to select AUTO.
2. Set your desired temperature using the TEMP ˄
or TEMP ˅ button.
3. Press the ON/OFF button to start the unit.
COOL mode
1. Press the MODE button to select COOL mode.
2. Set your desired temperature using the TEMP ˄
or TEMP ˅ button.
3. Press FAN button to select the fan speed in a
range of AU-100%.
4. Press the ON/OFF button to start the unit.
5. HOW TO USE BASIC FUNCTIONS

DRY mode (dehumidifying)
1. Press the MODE button to select DRY.
2. Set your desired temperature using the TEMP ˄
or TEMP ˅ button.
3. Press the ON/OFF button to start the unit.
Note: FAN speed cannot be changed in DRY
mode.
FAN mode
1. Press the MODE button to select FAN mode.
2. Press FAN button to select the fan speed in a
range of AU-100%.
3. Press the ON/OFF button to start the unit.
Note: You can’t set temperature in FAN mode. As
a result, your remote control’s LCD screen will not
display temperature.

HEAT mode
1. Press the MODE button to select HEAT mode.
2. Set your desired temperature using the TEMP ˄
or TEMP ˅ button.
3. Press FAN button to select the fan speed in a
range of AU-100%.
4. Press the ON/OFF button to start the unit.
Note: As outdoor temperature drops, the
performance of your unit’s HEAT function may be
affected. In such instances, we recommend using
this air conditioner in conjunction with other
heating appliances.

Setting the TIMER
TIMER ON/OFF - Set the amount of time after which the unit will automatically turn on/off.
TIMER ON setting
TIMER OFF setting
Note:
1. When setting the TIMER ON or TIMER OFF, the time will increase by 30 minutes increments with each
press, up to 10 hours. After 10 hours and up to 24, it will increase in 1 hour increments. (For example, press
5 times to get 2.5h, and press 10 times to get 5h,) The timer will revert to 0.0 after 24.
2. Cancel either function by setting its timer to 0.0h.
TIMER ON & OFF setting (example)
Keep in mind that the time periods you set for both functions refer to hours after the current time.
Press TIMER button to initiate the ON
time sequence.
Press Temp ˄ or ˅ button for multiple times to
set the desired time to turn on the unit.
Point the remote to unit and wait 1 sec. The
TIMER ON will be activated.
Press TIMER button to initiate the OFF
time sequence.
Press Temp ˄ or ˅ button for multiple times to
set the desired time to turn off the unit.
Point the remote to unit and wait 1 sec. The
TIMER OFF will be activated.
Timer starts
Unit turns ON
Unit turns OFF
Current time
1 PM
2.5 hours later
5 hours later