Frameit TV HANG iT User manual

INSTRUCTION MANUAL

Needed to Assemble:
Stud Finder
Optional in case of wood or concrete mounting surface:
Drill bit for concrete:
-Size: 1/8
-Bit Length: 1 ¾”
Items Included in box:
(a) Phillips screwdriver (b) Horizontal Level (c) 4 x wood/concrete Screws (drill bit
required for concrete surface)
(d) 1 x 90-degree edge ruler (f) 4 x Concrete Anchors to be used with
provided concrete screws
(e) 4 x Drywall anchors
PAGE 1
(g) 4 x Drywall Anchor Screws
Roll of blue painters tape Measuring tape/
Tape Measure
Pencil or Pen for marking
power
edge
Drill for concrete mounting
6
4
2
1
8
(h) 4 x Mounting Template Pieces

Frame Assembly Steps:
Template Assembly:
Step 1:
Assemble the mounting template following a clockwise sequence as labeled in each part.
Step 2:
Secure each part by placing blue tape across each section joint.
Step 3:
Repeat taping process on backside of template to ensure all sections are well aligned.
PAGE 2

Step 4:
Finding and marking the midpoints on TV top section (horizontal) and right side section (vertical).
Using blue tape and pencil/pen to mark midpoints.
A
Finding TV Midpoints
Visually estimate the midpoint of TV top/horizontal
section and place a 4 inch piece of tape along the
outside TV border as shown in illustration A. Repeat
process for right side vertical section as shown.
B
Measure entire length of top and right side
sections to identify midpoints.
PAGE 3

Step 5:
Once exact midpoints have been identied, place a line marking on blue tape as shown in gure 5.
Step 6:
Place a strip of blue tape on wall adjacent to the midpoint marked on TV (top and right side of TV
sections marked).
PAGE 4

Step 7:
Using the 90-degree straight edge provided, align midpoint markings on television with blue tape on the
wall and place the corresponding marking so that TV midpoint markings and blue tape markings on the
wall are now accurately aligned.
Template Placement on Wall & Mounting Hole Markings
Step 8:
A. Precut 8 pieces of blue tape 3 inches long and place near by for easy access (placing the 8 pieces
directly on TV screen is convenient for quick easy access).
PAGE 5

C. Once aligned, secure template to wall at each corner and just o the midpoints of each vertical
and horizontal sections through out perimeter of frame.
MP
MP
B. Maneuver template by placing around and behind top left corner of TV followed by bottom left corner.
Once template is behind TV on the left side, slide gently toward the right and repeat process on the right
side. The top/horizontal and right side (MP) midpoint markings on blue tape on wall will align with
midpoint markings on template. If o slightly, adjust template horizontally and vertically as needed to
reach both alignments on wall blue tape markings with template midpoints (top & side sections).
MP
MP
MP
MP
*MP = Midpoint
PAGE 6

PAGE 7
D. Use provided “level” to ensure template is evenly positioned horizontally by placing level at
dierent point on top horizontal edge of template. Also, check vertical alignment using level.
MP
MP
MP
MP

E. Conrm midpoint alignments using the provided 90 degree edge ruler.
Midpoints marked on TV should perfectly align with midpoint markings on template.
MP
MP
Locate Mounting Holes
Locate “Mounting Holes” on template by gently sliding TV on the wall bracket until the mounting holes are
within comfortable reach. Shift TV to side by pushing TV to right or left. *Don’t worry; TV will not fall o
bracket, as there are safety stoppers at each end of bracket preventing TV from coming o.
PAGE 8
Gently slide TV to the Right
Gently slide TV to the Left

PAGE 9
Step 9:
A. Place marking using pencil/pen at the CENTER of each mounting hole. Mounting hole as shown
in illustration: A, B, C & D.
A
Marking Mounting Holes
B
C D
Step 10:
Remove mounting template from the wall.
MP
MP