Fraser Hill Farm Let It Snow Series User manual

1) Schematic diagram
2) Component list
No.
Name
Number
1
Lamptop
1
2
Lampholder
1
3
Lamppost (17in）
2
4
Adapter(12VAC500mA)
1
5
Extended wire (137in)
1
6
Powerwire (137in)
(insidelamp post: 59in, outside: 78in)
1
7
Additionalbase
1set（4）
8
Ground nail
4
9
Lampbase
1
10
Squarebase
1
11
Brand
1
12
Lamppostjoint
1
13
Wreath+ bowknot
1set
14
Power wireoflamp holder
1
15
Screw
4+1
Note: 1,2,3,4,5,6are all wirejoints.
3) Assembling steps
Please assemble the product from the bottom to the up,
following themainstepsbelow:
1. Installlamp base
A. Assemble lamp base (9) and square base (10) with 4
screws:
B. Assemble 4 pieces of additional base (7) into a whole,
and then assemble the whole additional base (7) with the
lampbase (9).
Note: The additional base (7) is designed to fasten the
street lamp more securely. If the street lamp is installed on
a flat ground and there is no external force (such as high
wind or man-made interference), or if the street lamp is
used outdoors and it can be fixed on the ground by
fastening ground nails; there is no need to install additional
base (7). In other words, users can decide whether to
install the additional base (7) according to the actual
condition.
2. Install lamp post
Screw the two lamp posts (3), lamp post joints (12) and
square lamp base (10) together according to the sequence
shown in the figure below. Note: Every screw thread must
betightened;otherwise,thelamppostsmayleanorgetloose.
Caution
This product (especially the lamp holder) is
fragile, do not exert too much strength or drop it
during the assembly and use. Be sure to fix it on
thewallsecurely.
Please assemble it in strict accordance with
the steps and requirements specified in the
instruction to ensure safety and reliability
during the installation.

3. Install lamp holder
A. Thread the power wire (6) and its joint (5) through the
lamp base and lamp post (the lamp base and lamp post
canbe laiddownor put upside downforconvenience.After
drawingoutthejoint(5), placeit correctlyfor later use;
B.Takeoutthe lampholder (2)andputon thelamptop(1);
C. Draw out the joint (6) and the power line (14), connect
the joints (5) and (6), put the combined joints and their
wires into lamp post (3). Note: At this time, it will be better
to ask another person to hold thelamp holder (2) in caseof
droppingit.
D. Rotate the lamp holder (2) to fasten it on the lamp post
(3). Note: The screw thread shall be tightened as far as
possible. Meanwhile the direction of the lamp holder (2)
shall be slightly adjusted to make it match the direction of
thelampbases(9)and(10).
4.Positioning, power-on
andexamination
A. Positioning:Place carefullythe assembled street lamp at
thesetposition.Note: (1) Ifthestreetlampwillbeoutdoors,
place the lamp base into the ground with nails in case of
high winds; (2) The street lamp should be placed at a
location without man-made interference in case of
damages. (3) If the street lamp is to be installed indoors
and can be influenced by man-made interference or is to
be installed outdoors and ground nails can not be used,
please besure touse additional base(7) tokeep itsecure.
B. Power on: Tightly connect the two joints 1 and 4 of the
adaptor (4) and power wire (6). If the power wire isn’t long
enough, it is able to add the extended wire (5) between
them, and then connect the adapter (4) with the main
power source.
C. Make sure that the connection point between the
adapter and the main power source is indoors or at a place
free of rain or snow in case of electric leakage or electric
shock.Alljoints of 1,2, 3 and4, 5 and6mustbe tightened.
D. Examination: Whensetting the switch on the bottom of
the lamp holder (2) (see the figure below) to the left side,
the lamp should be lit, snowflake falling and music playing.
If it fails to perform suchfunctions,check if the joints 1, 2, 3,
4, 5 and 6 are well connected. You canalso turn the switch
to the right side to close themusic.
5. Decorate and enjoy
As shown in the figure below,
arrange the plaque (11) and the
wreath + bowknot (13) to the
uppersideofthe lamppost.
√