Freedom9 freeGuard Blaze 2100 User manual

freeGuard Blaze 2100
Specifications
Version 3R3
Last update: June 2007

COPYRIGHT NOTICE
© Copyright 2007 Freedom9 Inc.
ALL RIGHTS RESERVED.
Under the copyright law, this manual and the software described within can not be copied in
whole or part, without written permission of the manufacturer, except in the normal use of the
software to make a backup copy. The same proprietary and copyright notices must be affixed to
any permitted copies as were affixed to the original. An exception does not allow copies to be
made for others, whether or not sold, but all of the materials purchased can be sold, given, or
loaned to another person. Under the law, copying includes translating this information into
another language or format.
Information contained in this document is subject to change without notice.
TRADEMARKS
Hyper-Terminal is a registered trademark of Hillgraeve Inc.
SecureCRT is a registered trademark of VanDyke Technologies Inc.
Other products mentioned in this document may be trademarks and/or registered trademarks of
their respective companies and are the sole properties of their respective company.

. . . . .
Security Appliance Specifications Guide 2-iii
. . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents
1 Specifications 1-1
Package Contents 1-1
freeGuard Blaze 2100 1-2
LED Activity 1-3
Console Interface 1-4
Reset Switch 1-5

2-iv Security Appliance Specifications Guid

3R3Security Appliance Specifications Guide 1-1
S PECIFICATIONS 1
This document describes the physical attributes, electrical information
and environmental requirements to properly install and run the
freeGuard Blaze 2100. It includes the following topics:
•Package Contents
•freeGuard Blaze 2100 appliance
•LED Activity
•Console Interface
•Reset Switch
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PACKAGE CONTENTS
The freeGuard Blaze 2100 packaging includes the following:
• One freeGuard Blaze 2100 appliance
• One Power Cord
•TwoEthernetcables
• One console cable
• Quickstart Guide
• CD containing:
 Software for the freeGuard Blaze 2100
 User Guide
 CLI Reference Guide and Command Descriptions
 User Scenarios Guide
 Software Release Note

SPECIFICATIONS
freeGuard Blaze 2100
1-2 Security Appliance Specifications Guide Version 3R3
1
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FREEGUARD BLAZE 2100
Figure 1-1 is an image of the freeGuard Blaze 2100.
Figure 1-1: freeGuard Blaze 2100
Table 1-1 shows the hardware specifications of the freeGuard Blaze 2100
Table 1-1: Hardware Specifications
Parameter Value
Interfaces 8 Gigabit Ethernet, 1000Base-T (RJ-45) and
8 1000Base-X SFP slots (SX, LX, ZX)
Chassis 1U, rack-mountable
Dimensions (W x H x D) 426 x 44.4 x 324 mm
Weight 7 kg
Fans 2
Power Supply 90 to 264V AC, 47-63Hz
Operational
Temperature
5º to 40ºC
Storage Temperature -40º to 70ºC
Humidity 5% to 85%
Max Power
Consumption
40W
Safety Compliance UL, cUL, CE, CB
EMC Compliance FCC Class A, ICES Class A, VCCI Class A

. . . . .
SPECIFICATIONS
LED Activity
Version 3R3Security Appliance Specifications Guide 1-3
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LED ACTIVITY
Table 1-2 lists information about the physical interfaces on the freeGuard
Blaze 2100.
Table 1-2: Physical Interfaces Table
For additional information on interface configuration refer to the
“Security Zones and Interfaces” chapter in the User Guide.
Table 1-3 describes the LED Copper Interface activity on the freeGuard
Blaze 2100.
Interface Name Interface Type Default Zone
eth0 Interface Copper 1000base-T
or 1000Base-X
Global
eth1 Interface Copper 1000base-T
or 1000Base-X
Global
eth2 Interface Copper 1000base-T
or 1000Base-X
Global
eth3 Interface Copper 1000base-T
or 1000Base-X
Global
eth4 Interface Copper 1000base-T
or 1000Base-X
Global
eth5 Interface Copper 1000base-T
or 1000Base-X
Global
eth6 Interface Copper 1000base-T
or 1000Base-X
Global
eth7 Interface Copper 1000base-T
or 1000Base-X
Global
Table 1-3: LED Copper Interface Activity
Interface Copper Right LED Left LED
1000Mb Full Duplex Activity-Green On-Green
100Mb Full Duplex Activity-Green Off
10Mb Full Duplex Activity-Green Off

SPECIFICATIONS
LED Activity
1-4 Security Appliance Specifications Guide Version 3R3
1
Table 1-4 describes the fiber interface activity on the security appliance
Table 1-4: LED Fiber Interface Activity
Interface Fiber Link ACT
1000Mb Full Duplex On-Orange Activity-Orange

. . . . .
SPECIFICATIONS
Console Interface
Version 3R3Security Appliance Specifications Guide 1-5
Table 1-5 shows the LED Status Description
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CONSOLE INTERFACE
Use the console cable provided to manage the freeGuard Blaze 2100
through the console interface. Figure 1-2 displays the location of the
console interface on the freeGuard Blaze 2100.
Figure 1-2: Console Interface
For additional information on console interface management refer to the
“System Management” chapter in the User Guide.
Table 1-5: LED Status Description
LED Behavior Meaning
Flashing Green Firewall is loading
Solid Green Firewall is operating
Off Firewall is not operating

SPECIFICATIONS
Reset Switch
1-6 Security Appliance Specifications Guide Version 3R3
1
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RESET SWITCH
The reset switch shown in Figure 1-3 can be found inside the freeGuard
Blaze 2100 and is used to return the running software image to factory
default. The default software image and no configuration file will be
loading during boot-up. To access the reset switch you have to open the
chassis of the freeGuard Blaze 2100 and locate the reset button, which is
located towards the rear right hand side of the chassis.
Figure 1-3: Reset Switch
For additional information on console interface management refer to
refer to the “System Management” chapter in the User Guide.