Frigidaire FRA104CV111 User manual

FRIGIDAIRE
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii__
iii¸/im
Product
ackaging .;,
aormat sounds :L
www,frigJ

This USE & CARE MANUAL provides specific operating instructions for your model. Use the room air conditioner only as
instructed in this USE & CARE MANUAL. These instructions are not meant to cover every possible condition and situation that
may occur. Common sense and caution must be practiced when installing, operating, and maintaining any appliance.
The power supply cord with
this air conditioner contains a current
detection device designed to reduce the risk
of fire.
UPlease refer to the section 'Operation of
Current Device' for details.
For Your Safety
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any
other appliance. Read product labels for flammability and other warnings.
In the event that the power supply cord is Prevent Accidents
damaged, it cannot be repaired, tt must be
replaced with a cord from the product To reduce the risk of fire, electrical shock, or injury to persons when using your air conditionel
manufacturer, followbasicprecautions,includingthefollowing:
° Be sure the electrical service is adequate for the model you have chosen. This information
Avoid fire hazard or electric shock. Do not
use an extension cord or an adaptor plug. Do
not remove any prong from the power cord.
can be found on the serial plate, which is located on the side of the cabinet and behind the
grille.
• If the air conditioner is to be installed in a window, you will probably want to clean both
iiii ii sides of the glass first. If the window is a triple-track type with a screen panel included,
remove the screen completely before installation.
• Be sure the air conditioner has been securely and correctly installed according to the
separate installation instructions provided with this manual. Save this manual and the
installation instructions for possible future use in removing or reinstalling this unit.
•When handling the air conditioner, be careful to avoid cuts from sharp metal fins on front
and rear coils.
DANGER.IAvoid Serious Injury or Death
This air conditioner contains no user-serviceable parts. Always call an authorized Electrolux servicer for repairs.
Do not insert or place fingers or objects into the air discharge area in the front of the unit.
Do not start or stop the air conditioner by unplugging the power cord or turning off the power at the electrical box.
Do not cut or damage the power cord.
If the power cord is damaged, it should only be replaced by an authorized Electrolux servicer.
In the event of a malfunction (sparks, burning smell, etc.), immediately stop the operation, disconnect the power cord, and call an authorized
Electrolux servicer.
• Do not operate the air conditioner with wet hands.
• Do not pull on the power cord.
• Do not drink any water that is drained from the air conditioner.
02009 Electrolux Home Products, Inc. All rights reserved.

o
o
CAUTION. IAvoid Injury or damage to the unit or other property
Provide occasional ventilation during use. Do not direct airflow at fireplaces or other heat related sources as this could cause flare ups or make
units run excessively.
Do not climb on or place objects on outdoor part of the unit.
Do not hang objects off the unit.
Do not place containers with liquids on the unit.
Turn off the air conditioner at the power source when it will not be used for an extended period of time.
Periodically check the condition of the unit's installation accessories for any damage.
Do not apply heavy pressure to the radiator fins of the unit.
Operate the unit with air filter in place.
Do not block or cover the intake grille, discharge area and outlet ports.
Ensure that any electrical/electronic equipment is one yard away from the unit.
Do not use or store flammable gases near the unit.
READ THIS SECTION BEFORE ATTEMPTING TO OPERATE AIR CONDITIONER.
Unit must be upright for one hour prior to operating.
Operation of Current
Device
Plug in & _,
press RESET
The power supply cord contains a current device that senses damage to the power cord. To test
your power supply cord do the following:
1. Plug in the Air Conditioner.
2. The power supply cord will have TWO buttons on the plug head. Press the TEST button. You will
notice a click as the RESET button pops out.
3. Press the RESET button, Again you will notice a click as the button engages,
4. The power supply cord is now supplying electricity to the unit,
Do not use this device to turn the unit on or off.
• Always make sure the RESET button is pushed in for correct operation.
, The power supply cord must be replaced if it fails to reset when either the TEST button is pushed,
or it cannot be reset. A new one can be obtained from the product manufacturer.
•If power supply cord is damaged, it CANNOT be repaired, It MUST be replaced by one obtained
from the product manufacturer.
02009 Electrolux Home Products, Inc. All rights reserved.

Product Registration Record Your Model and Serial Numbers
Record in the space provided below the model and serial numbers. On all models, the
serial plate is located on the outside of the cabinet.
Model No.
Serial No.
Register Your Product
The self-addressed PRODUCT REGISTRATION CARD should be filled in completely,
signed and returned to the Frigidaire Company.
Packaging Remove all packaging from inside the carton, along with any
inserts placed into the side louvers.
PACKAGING INSERTS
: i
! r
o/o o- o jj
Normal Sounds
High pitched Chatter
Today's high efficiency compressors
may have a high pitched chatter
during the cooling cycle.
Sound of Rushing Air
At the front of the unit, you may
hear the sound of rushing air
being moved by the fan.
Vibration
Unit may vibrate and make noise
because of poor wall or window
construction or incorrect installation.
4
Pinging or Swishing
Droplets of water hitting condenser
during normal operation may cause
"pinging or swishing" sounds.
Gurgle/Hiss
"Gurgling or hissing" noise may be
heard due to refrigerant passing
through evaporator during normal
operation.
@2009 Electrolux Home Products, Inc. All rights reserved.

Air Conditioner Features ELECTRONICCONTROL
F
f TEMP/TIMER
TEMP/TIMER ..i
CLEAN AIR
FEATURE SENSING INDICATOR DISPLAYS
(some models) -- (some models) TEMPERATURE/TIME _ CHECK FILTER
RESETBUTTON
dean cod remote hi filter
econ sensing med
air Sanonly lo reset ]
er MODE VON-OFF AFAN SPEED s|qep /
SETS NODE ADJUSTS SETS FAN
TEMPERATURE SPEED
OR TIME
0 0 0
coot energy fan
saver only
© © 0
sleep auto timer
fan
fFRIGIDAIRE _
STANDARD REMOTE
F G o q
fTEHPITIHER
,_. TENP/TIMER
oo0
cool energy fan
saver on{y
[] © []
steep auto timer
fan
start [_ stop
remote sensing
fFRIGID_IRE "_
_J
w/DISPLAY &
REMOTE SENSING
BUTTON
REMOTE TEMP
Before you begin, thoroughly familiarize yourself with the control panel and remote
as shown below and all its functions, then follow the symbol for the functions you
desire. The unit can be controlled by the touch pad alone or with the remote.
!
Battery Size: AAA
Warning: Do not mix old and new batteries. Do not mix alkaline,
standard (carbon-zinc), or rechargeabte (nickel-cadmium) batteries.
Operating Instructions
The following instructions represent the Touch Pad, the same instructions can be used for the Remote Control.
TO TURN UNIT ON: YOU WILL SEE:
letup/timer )
Iauto I
cool remote I _ hi
econ sensing I _ reed I
fan only _to )
_i
MODE V 0N-0FF A FAN SPEED
oo,..,:i
RESS ON/OFF BUTTON
Lromp/timer )
I F auto I
[] coot remote _ I hi []
econ sensing _ _ med
fan only _lo J
MODE V 0N-0FF AFAN SPEED
@2009 Electrolux Home Products, Inc, All rights reserved, !--

Operating Instructions
(continued)
TO CHANGE TEMPERATURE SETTING:
remote
sensing
tamp/timer
auto
hi [] fi|termed
Zo reset
V ON=OFF A FAN SPEED
DO THIS:
PRESS A TO RAISE
PRESSV TO LOWER
sleep
YOU WILL SEE:
remote
sensing
tamp/timer F
auto
hi , filter
mad
Zo reset
V ON=OFF A FAN SPEED sleep
Note: Tap or hold either up ( A ) or down ( V ) button until
the desired temperature is seen on the display. This tempe-
rature will be automatically maintained anywhere between
60 °F (16 °C) and 90 °F (32 °C). If you want the display to
read the actual room temperature. See "To Operate on Fan
Only" section on Page 7.
TO AD3UST FAN SPEEDS:
emote
sensing
temp/timer F
vON-OFF A
auto ,,/1
hi .filter
med
Zo reset
FAN SPEED sleep
\DO THIS:
YOU WILL SEE:
remote
sensing
temp/timer auto !
medhi /filter
lo , reset
VON-OFF A FAN SPEED sleep
PRESSTO SELECT
TO USE AUTO FAN FEATURE:
remote
sensing
tamp/rimer
auto J
reed
lo []
lifter
reset
V ON-OFF AFAN SPEED
,_
-\
DO THIS;
sleep
PRESSFAN BUTTON,
CHOOSEAUTO
YOU WILL SEE:
remote
sensing
temp/timer auto [] I
medhi /fitter
Zo reset
V0N=0FF A FAN SPEED sleep
Note: Fan starts at High Speed and adjusts to a slower
speeds the room temperature dictates. For example, if the
room doesn't get too warm, it will stay at the slowest speed.
If the room temperature rises quickly, such as a door being
opened, it will automatically go to the highest speed. The fan
speeds will re-adjust back to the slowest speed as the room
returns to the original set temperature. Press either the fan
slower or fan faster button to adjust the fan speed manually.
@2009 Electrolux Home Products, Inc. All rights reserved.

Operating Instructions
(continued)
TO OPERATE ON FAN ONLY:
f
ctearl _ m cool remote
\econ sensing
air #n only
temp/timer m
timer MODE V ON-OFF A
DO THIS:
PRESS
MODE BUTTON
CHOOSE
FAN ONLY
YOU WILL SEE:
c[eall _cool remote
\econ sensing
air [] #n only
temp/timer
timer MODE V 0N-0FF A
Note: Use this function only when cooling is not desired,
such as for room air circulation or to exhaust stale air on
some models. (Remember to open the vent during this
function, but keep it closed during cooling for maximum
cooling efficiency.) You can choose any fan speed you
prefer. (Except "Auto Fan").
During this function, the display will show the actual room
temperature, not the set temperature as in the cooling
mode.
TO USE THE ENERGY SAVER (ECON) FEATURE:
dean \ cool remote
\econ sensing
air []fanonly
temp/timer m
timer MODE V ON-OFF A
DO THIS;
PRESS
MODE BUTTON
CHOOSE ECON
YOU WILL SEE:
dean \ cool remote
air _ ,econ sensing
Ion only
temp/timer m
timer MODE V ON-OFF A
Note: In this mode, the fan will continue to run for 1 minu-
te after the compressor shuts off. The fan then cycles on
for 20 seconds at 10 minute intervals until the room tempe-
rature is above the set temperature, at which time the com-
pressor turns back on.
SLEEP FEATURE: YOU WILL SEE:
romp/timer l
remote hi []
sensing reed
Io
V ON-OFF A FAN SPEED
fitter
reset
steep
DO THIS:
PRESS
SLEEP BUTTON
remote
sensing
temp/timer Fmauto J
hi m
reed
lo
V ON-OFF A FAN SPEED
fitter
reset
w
steep
Note: In this mode the selected temperature will increase
by 2 °F 30 minutes after the mode is selected. The tempe-
rature will then increase by another 2 °F after an additional
30 minutes. This new temperature will be maintained for 7
hours before it returns to the originally selected tempera-
ture. This ends the "Sleep" mode and the unit will continue
to operate as originally programmed. The "Sleep" mode
program can be cancelled at any time during operation by
again pressing the "Sleep" button.
02009 Electrolux Home Products, Inc. All rights reserved.

Operating Instructions
(continued)
TIMER: DELAY STOP JSTART FEATURE
f
clean _=cool remote
kecon sensing
air Ion only
temp/dmer
Hr
timer NODE V 0N-0FF
YOU WILL SEE HOW MUCH TIME IS CHOSEN:
clean i [] cool
econ
air fan only
[]
timer NODE
remote
sensing
temp/timer
v ON-OFF A
\\FI RST
DO THIS:
PRESS
TIMER BUTTON
THEN
DO THIS:
PRESS
UP/DOWN BUTTONS
Note: For Delay Stop, the unit must be in the On position.
Note: For Delay Start, the unit must be in the Off position.
First, Press TIMER button, then adjust timer setting, tap or hold the UP arrow ( A ) or the DOWN arrow ( V ) to change delay
timer at 0.5 hour increments, up to 10 hours, then at 1 hour increments up to 24 hours. The control will count down the time
remaining until start (8, 7.5, 7, etc.). The Delay Start Operation automatically selects cooling with maximum Fan speed (if Cool,
Energy Saver, or Fan Only was the last mode selected). The temperature maintained will be the same as previously set. To change
the set temperature, press "COOL" then Up or Down arrows until the desired temperature is indicated on the display. After 5
seconds, the control will automatically change the display back to the hours remaining until the unit will start/stop. Pressing the
unit On/Off button at any time will cancel the Delay Start/Stop function. The Delay Start/Stop Feature will work until the unit either
starts or stops. Once that happens the above steps have to be repeated again.
CHECK FILTER FEATUREr YOU WILL SEE:
temp/timer l
mauto.
remote hi filter
sensing med
lo reset
V 0N-0FF AFAN SPEED sleep
Note: This feature is a reminder to clean the Air Filter (See
Care and Cleaning) for more efficient operation. The LED
(light) will illuminate after 250 hours of operation. To reset
after cleaning the filter, press the "Filter Reset" button and
the light will go off.
CLEAN AIR FEATURE(on some models):
temp/timer )
Fauto [] I
remote _T| _ hi I filter
sensing _ I_ reed Ireset
lo ]
V 0N-0FF A FAN SPEE_
/
DoTHIS:/I
PRESS FILTER
RESET BUTTON
temp/timer F
dea. \ ,cool remote m
• I econ sensing role i_W m
alr L fan only
MODE V 0N=0FF A
DO THIS:
PRESS
CLEAN AIR
BUTTON
8@2009 Electrolux Home Products, Inc.
clean [] coo! remote
air ;aCOnnonlysensing
temp/timer
timer MODE V ON=OFF A
m
Note: When this feature is "ON", the electronic air purifier is
energized to remove pollen and impurities from the air. To
cancel this feature, press the Clean Air button (the LIGHT
will turn off).
Note: This feature can be activated on the unit touch pad
ONLY, All rights reserved,
ii!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!!!ii;i!ii

Operating Instructions
(continued)
REMOTE SENSING FEATURE
(on some models).
o
\ s
| I
TEMp/TIMER
_ Q o
remote 5e#sing
DO THIS:
PRESS REMOTE
SENSING
START BUTTON
dean
air
LIGHT pulsing ( On & Off intermittently ).
cool remote F
econ sensing
#n only |
timer MODE V ON-OFF A
NOTE: Unit display shows the set temperature
o
__J
NOTE: Remote display
is actual temperature
at remote control only
Note: This feature can be activated from the remote control ONLY, the unit must be in a cooling mode.
To activate the remote sensing feature, point the remote control towards the unit and press the remote sensing Start button. Next, use
the" A V "buttons to set the desired temperature at the remote. (Note that the set temperature will only be displayed on the unit
itself ). The LIGHT on the unit control wilt pulse to indicate it received the signal. The LIGHT on the remote control will pulse each time it
sends a signal. It will periodically send this signal until the feature is deactivated by pressing the remote sensing Stop button. If the unit
does not receive the remote sensing signal during any 3 minute interval, the unit wilt beep to indicate the remote sensing mode has
ended. The display on the remote control indicates the temperature at the remote ONLY.
NOTE: The Remote Sensing function is terminated either by using the Remote Sensing Stop button or the main ON/OFF button on the
unit.
FAULT CODES:
remote
sensing
ternp/timer
auto [] i
medhi fitter
lo reset
V 0N=0FF AFAN SPEED sleep
If the display reads "AS", a sensor has failed. Contact your
Authorized Frigidaire Service Center.
TO CHANGE TEMPERATURE DISPLAY:
temp/timer l
m°ut°
remote hi .filter
sensing reed
lo reset
VON-OFF A FAN SPEED
/DO THIS:
PRESS AND HOLD THE
UP/DOWN BUTTONS
TOGETHER FOR 3 SECONDS
sleep
YOU WILL SEE:
remote
sensing
temp/timer mauto ;
hi , fitter
reed
lo reset
VON-OFF A FAN SPEED sleep
Note: The control is capable of displaying temperature in
degrees Fahrenheit or degrees Celsius.
@2009 Electrolux Home Products, Inc. All rights reserved, r-_

Operating Instructions
(continued)
TO TURN UNIT OFF:
remote
sensing
temp/timer
auto J
hi. fitter
med
Io reset
V ON-OFF AFAN SPEED s[eep
oo_j
PRESS
ON/OFF BUTTON
YOU WILL SEE;
temp/timer auto l
remote I I hi fitter
sensing med
lo reset
V ON-OFF A FAN SPEED s[eep
ADDITIONAL THINGS YOU SHOULD KNOW
Now that you have mastered the operating procedure, here are more features in your control that you should become familiar with.
•The "Cool" circuit has an automatic 3 minute time delayed start if the unit isturned off and on quickly.
This prevents overheating of the compressor and possible circuit breaker tripping. The fan will continue
to run during this time.
, There is a 2-Second delay for the compressor shutting down when selecting FAN ONLY. This is to cover the possibility of having
to roll through to select another mode.
• The control will maintain the set temperature within 2 degrees Fahrenheit, between 60F and 90F degrees.
• After a power outage, the unit will memorize the last setting and return the unit to the same setting once power is restored.
I
Figure i(VENT CLOSED)
........_':::: ..... ........... _- =
_Y5 -_'?,_T'_:_ _h I_l ......
Figure 2 (FRESH AIR)
Fresh Air Vent Control (on some models)
The Fresh Air Vent allows the air conditioner to:
1. Recirculate inside air - Vent Closed (see Fig. 1)
2. Draw fresh air into the room - Fresh Air (see Fig. 2)
3. Exchange air from the room - Vent Open (see Fig. 3)
AUGER WHEELS
(8-WAY)
Air Directional Louvers
Air directional louvers control air flow direction. Your air conditioner has the louver
type described below.
Auger Type
The louvers will allow you to direct the air flow Up or Down and Left or Right
throughout the room as needed. Rotate the Auger Wheels until the desired
Left/Right direction is obtained. Pivot horizontal louvers until the desired
Up/Down direction is obtained.
0 ©2009 Electrolux Home Products, Inc. All rights reserved.