Frigidaire 131888900 User manual

(7)- (417/FRIGIDAIRE) FRONT LOAD WASHER DOOR
LOCK/SWITCH KIT #131888900.

INSTALLATION INSTRUCTIONS
DOOR LOCK/SWITCH KIT - P/N 131888900
This kit replaces the Bitron door lock/switch with a US Controls door lock/switch.
This kit contains the following parts:
(1) Door Lock/Switch
(1) Door Strike
(1) Adapter Harness
(1) Tube Adhesive
(6) Plastic Harness Ties
(1) Installation Instruction
1. Disconnect the washer from the electrical power
source.
2. Remove the front service panel.
3. Open the door, remove the two screws securing the
door strike to the door and remove the strike.
4. Install the new door strike using the screws removed
in step 3.
5. Using a razor blade or a sharp putty knife, separate
the bellows from the front panel at the 2, 3, & 4
o'clock positions.
6. Remove the screws securing the old door
lock/switch to the front panel.
7. Remove the wires from the old door lock/switch and
remove the switch.
8. Remove the nine pin plug from the speed control
unit (SCU).
9. NOTE: Iftlae washer serial number prefix is XC703
and above, go to step 13. If the washer serial number
is below XC703, proceed with instructions 10
through 12.
10. In slot number 2, insert a small wire (paper clip)
between the locking tab of the red wire terminal and
the housing. Note: The locking tab is located in the
small rectangular slot below the terminal. DO NOT
push down on the contact prongs on the wire
terminal.
11. Pull the red wire out of the slot.
12. Insert the red wire into slot number 4 until the
terminal clicks into the housing. Gently pull on the
wire to ensure it is fully seated in the housing.
13. Remove the connector plug from the pump. NOTE:
Removing the pump cover on pumps with an
external cooling fan will make it easier to access the
connector plug.
14. Connect the nine pin plug from the adapter harness
to the to the SCU.
P/N 131888800 8/99

i:, Connecttilenine[)mplugremovedinstep8tothe
connectorboardontheadapterharn_:ss.
i_.Dresstheadapterharnessalongsideofthepresent
washerharnessasshown¸
!!. Using the plastic harness ties, attach 1he adapter
harness to the washer harness. Dress the hmness in
such a manner that it will not interlierc with any
moving parts or cause ally noise when die washer is
m operation.
i?. Connect the green connccto_ plug ll-om lhe adapte_
harness to the pump. Re-install the pump cover, if it
was removed in step !3.
I8. Connect the green connector phlg fiom the washer
harness to the connector on the adapter harness.
19. NOTE: If the service kit's door lock is already pre-
wired to the adapter harness, go to step 20. If the
service kit's door lock is not pre-wired to the adapter
haHless, conned the adapter haraess connections to
the new door lock
2(} Matching color [br color, connect the door switch
wires fiom tile washe_ harness to the connectols m
the adapter harness
21 Install the new door lock to the washer cabinet using
tile same screws removed in step 6
23. Connect the washer to the electrical power source
and test for proper operation. Close the door, place
Ibe iilnel to the final spin positioa, and start tile
lilner. When the machine starts its tRst ramp up to
tile higber spin speed, turn the tirner off; then
quickly pul! on the door handle to verify the door is
locked, lltlle door opens, recheck the connections in
steps 9 through 12
24 Using the tube of adhesive, glue the bellows to tile
l}ont panel at the 2. 3, & 4 o'clock positions. Wait
about two minutes, tllen pull on the bellow to make
sure it is securely bonded to the flon! pane!.
2q Install the li-ont sel vice pntm!