Frigidaire Affinity 6000 Series User manual

All About
Servicing
Affinity Front Load
6000 & 7000 Series
3.5 Cu. Ft. Washers
™
Publication #5995536298 March 2009
Electrolux Major Appliances; North America
250 Bobby Jones Expwy
Augusta, GA 30907

Section 1 Basic Information
1-1
Safe Servicing Practices
Avoid personal injury and/or property damage by observing important Safe Servicing Practices.
Following are some limited examples of safe practices:
1. DO NOT attempt a product repair if you have any doubts as to your ability to complete the repair in a safe and
satisfactory manner.
2. Always Use The Correct Replacement Parts as indicated in the parts documentation. Substitutions may defeat
compliance with Safety Standards Set For Home Appliances.
3. Before servicing or moving an appliance:
• Remove power cord from the electrical outlet, trip circuit breaker to OFF position, or remove fuse.
• Turn off water supply.
4. Never interfere with the proper operation of any safety device.
5. Use ONLY REPLACEMENT PARTS CATALOGED FOR THIS APPLIANCE. Substitutions may defeat compliance with
Safety Standards Set For Home Appliances.
6. GROUNDING: The standard color coding for safety ground wires is GREEN, or GREEN with YELLOW STRIPES.
Ground leads are not to be used as current carrying conductors.
It is EXTREMELY important that the service technician reestablish all safety grounds prior to completion of
service. Failure to do so will create a hazard.
7. Prior to returning the product to service, ensure that:
• All electrical connections are correct and secure.
• All electrical leads are properly dressed and secured away from sharp edges, high temperature components, and
moving parts.
• All non-insulated electrical terminals, connectors, heaters, etc. are adequately spaced away from all metal parts
and panels.
• All safety grounds (both internal and external) are correctly and securely connected.
• All panels are properly and securely reassembled.
• Electrical and water supplies are turned ON if shut off prior to service.
© 2009 Electrolux Home Products, Inc.
ATTENTION!!!
This service manual is intended for use by persons having electrical and mechanical training and a
level of knowledge of these subjects generally considered acceptable in the appliance repair trade.
Electrolux Home Products, Inc. cannot be responsible, nor assume any liability, for injury or damage
of any kind arising from the use of this manual.

Table of Contents
Section 1 Basic Information
Safe Servicing Practices....................................... 1-1
Table of Contents................................................ 1-2
Warnings and Cautions........................................ 1-3
Safety Instructions.............................................. 1-3
Protect Children .................................................. 1-4
Prevent Fire........................................................ 1-4
Serial / Model Number Breakdown........................ 1-5
Drum Water Height............................................. 1-5
Water Usages ..................................................... 1-5
Motor Wattage.................................................... 1-5
Component Resistance Chart ............................... 1-5
Washer Component Operation ............................. 1-6
Control......................................................... 1-6
Drum Light Assembly..................................... 1-6
Door Switch Assembly ................................... 1-6
Door Lock Assembly ...................................... 1-6
Pressure Switch............................................. 1-7
Electronic Water Level Sensor ........................ 1-8
Water Inlet Valve Assembly............................ 1-8
Water Valve Operation................................... 1-8
Water Temperature....................................... 1-10
Auto Temp System........................................ 1-10
Automatic Dispenser...................................... 1-11
Drain Pump................................................... 1-14
Motor........................................................... 1-15
Speed Control............................................... 1-15
Tub Construction........................................... 1-15
Warranty Information.......................................... 1-16
Section 2 Installation Information
Warnings............................................................ 2-1
Pre-Installation Requirements .............................. 2-2
Electrical System Requirements............................ 2-2
Grounding Requirements ..................................... 2-2
Unit Dimensions.................................................. 2-3
Water Supply Requirements................................. 2-4
Drain System Requirements................................. 2-4
Unpacking Unit ................................................... 2-4
Clearance Requirements
Installation in a Recess or Closet.......................... 2-5
Leveling Washer.................................................. 2-6
Connecting Inlet Water........................................ 2-6
Connecting Drain and Electrical............................ 2-7
Installation Checklist............................................ 2-7
Washer and Dryer 15” Drawer Pedestal
Installation ......................................................... 2-8
Section 1 Basic Information
1-2
Section 3 Electronic Control
Affinity 6000 & 7000 Series Control Panel Layout... 3-1
Operating Steps.................................................. 3-2
Cycle Selection.................................................... 3-2
Cycle Description ................................................ 3-2
Cycle Settings..................................................... 3-3
Cycle Options...................................................... 3-4
Washer Features................................................. 3-4
Affinity 6000 Series Cycle Chart............................ 3-5
Affinity 7000 Series Cycle Chart............................ 3-6
Troubleshooting Error Codes................................ 3-7
Reading Error Codes............................................ 3-7
Quick Check........................................................ 3-7
To Clear Latest Stored Error Code ........................ 3-7
Diagnostic Test................................................... 3-8
Exiting Diagnostic Mode....................................... 3-8
Drum Light Circuit Testing ................................... 3-8
Failure Code Chart............................................... 3-9
Tests 1-5............................................................ 3-11
Tests 6-16.......................................................... 3-12
Jacks and Plugs................................................... 3-13
Operation Speed Chart ........................................ 3-14
Section 4 Component Teardown
Warnings and Cautions........................................ 4-1
Door Strike......................................................... 4-2
Loading Door...................................................... 4-2
Loading Door Breakdown..................................... 4-2
Top Panel .......................................................... 4-3
Light Switch........................................................ 4-3
Detergent Drawer ............................................... 4-4
Detergent Drawer Disassembly............................. 4-4
Releasing The Bellows (Door Boot) From Front
Panel .............................................................. 4-5
Door Safety Switch.............................................. 4-5
Console.............................................................. 4-6
Electronic Control Board ...................................... 4-7
Removing The Delay Start Button................... 4-7
Removing The Interface Board ...................... 4-7
Removing The Selector Knob ......................... 4-7
Light Socket........................................................ 4-8
Front Panel......................................................... 4-8
Removing The Heater Control Board..................... 4-9
Removing The light Transformer .......................... 4-9
Removing The Transformer And Heater
control board mounting bracket............................ 4-9
Console Mounting Bracket.................................... 4-10
Bellows .............................................................. 4-10
Reinstalling Or Replacing The Bellows .................. 4-11
Weight Ring ....................................................... 4-12
External Drain Hose............................................. 4-12
Water Inlet And Overflow/Vent Tube Grommet...... 4-12
Overflow/Vent Tube ............................................ 4-13
Water Inlet Valve................................................ 4-13
Water Inlet Screen.............................................. 4-14

Section 1 Basic Information
1-3
Section 4 Component Teardown (Continued)
Top Rear Brace................................................... 4-14
Suspension Springs ............................................. 4-15
Top Center Brace................................................ 4-15
Detergent Cavity Assembly .................................. 4-16
Detergent Dispenser Outlet Hose.......................... 4-17
Siphon Break Hose.............................................. 4-17
Drain Pump ........................................................ 4-17
Drain Pump Disassembly...................................... 4-18
Electric Water Level Sensor.................................. 4-18
Drain Sump ........................................................ 4-19
Drain Pump Outlet Hose ...................................... 4-19
Drain Hose Coupler ............................................. 4-20
Rear Access Panel............................................... 4-20
Drive Belt ........................................................... 4-20
Large Pulley........................................................ 4-20
Drive Motor......................................................... 4-21
Speed Control Board Assembly............................. 4-21
Right Hand Air Shock Absorber............................. 4-22
Left Hand Air Shock Absorber............................... 4-23
Heating Element ................................................. 4-23
Drum Water NTC................................................. 4-23
Air Bell .............................................................. 4-24
Tub Assembly ..................................................... 4-24
Spin Basket Vanes............................................... 4-26
Section 5 Troubleshooting
Troubleshooting Chart (Customer Use Related) ..... 5-1
Troubleshooting Chart......................................... 5-2
Section 6 Wiring Diagrams
Affinity 7000 Series Wiring Diagram...................... 6-1
Affinity 6000 Series Wiring Diagram...................... 6-2
Recognize safety symbols, words and labels:
Safety items throughout this manual are labeled with a WARNING or CAUTION based on the risk type as described
below:
This symbol alerts you to situations that may cause serious body harm, death or
property damage.
This symbol alerts you to situations that may cause bodily injury or property damage.
Read all of the following instructions before installing and using this appliance:
• Destroy the carton and plastic bags after the washer is unpacked. Children might use them for play. Cartons
covered with rugs, bedspreads, or plastic sheets can become airtight chambers causing suffocation. Place all
materials in a garbage container or make materials inaccessible to children.
• Clothes washer installation and service must be performed by a qualified installer or service agency.
• Install the clothes washer according to the manufacturer’s instructions and local codes.
• The electrical service to the washer must conform with local codes and ordinances and the latest edition of the
National Electrical Code, ANSI/NFPA 70, or in Canada, the Canadian electrical code C22.1 part 1.
• The washer is designed under ANSI Z 21.5.1 or ANSI/UL 2158 - CAN/CSA C22.2 No. 112 (latest editions) for
HOME USE only. This washer is not recommended for commercial applications such as restaurants, beauty salons,
etc.
• The instructions in this manual and all other literature included with this washer are not meant to cover every
possible condition and situation that may occur. Good safe practice and caution MUST be applied when installing,
operating and servicing any appliance.
WARNING
CAUTION

Section 1 Basic Information
1-4
Protect Children
Do not allow children to play on or in the washer. Close supervision of children is necessary when the washer is used
near children. As children grow, teach them the proper, safe use of all appliances.
Destroy the carton, plastic bag and other packing materials after the washer is unpacked. Children might use them
for play. Cartons covered with rugs, bedspreads or plastic sheets can become airtight chambers.
Keep laundry products out of children’s reach. To prevent personal injury, observe all warnings on product labels.
Before the washer is removed from service or discarded, remove the washer door to prevent accidental entrapment.
Failure to comply with these warnings could result in serious personal injuries.
Prevent Fire
Do not obstruct the flow of ventilating air. Do not stack or place laundry or throw rugs against front or back of washer.
Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric
softener or product.
Failure to comply with these warnings could result in fire, explosion, serious bodily injury and/or damage to the
rubber or plastic parts of the washer.
To prevent personal injury or damage to the washer, the electrical power cord must be plugged into a properly
grounded and polarized 3-prong outlet. The third grounding prong must never be removed.
Never ground the washer to a gas pipe.
Do not use an extension cord or an adapter plug.
ALWAYS disconnect the washer from the electrical supply before attempting any service or cleaning. Failure to do
so can result in electrical shock or injury.
Do not use any type spray cleanser when cleaning washer interior. Hazardous fumes or electrical shock could occur.
To prevent injury, do not reach into the washer if the drum is moving. Wait until the washer has stopped completely
before reaching into the drum.
To prevent injury and damage to the washer:
• Use only authorized factory parts.
• Do not tamper with controls.
• Do not install or store the washer where it will be exposed to the weather.
WARNING

Section 1 Basic Information
1-5
Drum Water Height
Water fill height 3.5 ± .5 “
No load, start position of permanent press cycle.
(See Figure 1-2)
Water Usages
Based on 1 wash and 3 rinse fills.
Per fill............. 4.23 gallons
Per cycle......... 16.92 gallons
Motor Specifications
No load agitate wattage - Max 150
No load spin wattage - Max 550
Tub Pulley to Motor Pulley Ratio - 16 To 1
Serial Number Breakdown
4D82812345
Incremented unit number
Production Week
Last Digit of Production Year
Product Identification
Manufacturing Facility
Brand
Bundle/
Handle
Type
Capacity
Product
Style/
Level
Year
Model Color
Feature
AWF3510IHI
Model Number Breakdown
Resistance Ω
Electrical component @ 77 F (25 C)
Dispenser valve solenoids 800 ± 7%
Door lock solenoid 1325 ± 10%
Pump motor 12 ± 7%
NTC Thermistor dispenser 3K
NTC Thermistor heater 4.8K
Water heater 14 ± 10%
M1 TO M2 5.3 ± 7%
M2 TO M3 5.3 ± 7%
M1 TO M3 5.3 ± 7%
M4 TO M5 118 ± 7%
Motor
˚˚
Figure 1-2. Drum Water Height
Figure 1-1. Serial Tag Location
Component Resistance Chart Automatic Temperature Control Specifications
Auto Temp Sanitary Cycle.................... 152° ± 7° F
Auto Temp HOT/COLD setings............. 120° ± 7° F
Auto Temp WARM/WARM
and WARM /COLD settings ................. 90° ± 7° F
Auto Temp COLD/COLD settings ......... 65° ± 7° F
3.5”±1/2”

Section 1 Basic Information
1-6
Control
The control is mounted to the back of the console.
(See Figure 1-3) The control:
1. Provides power to the dispenser solenoids, wax
motor, door lock solenoid, drain pump and speed
control board.
2. Sends signals to the speed control board to tell it
what program to run and the heater control board to
control the heater.
3. Checks the status of the door switches, door light
switch, incoming water sensor and the drum water
sensor.
Drum Light Assembly (On select models)
The drum light assembly is made up of a 12 volt AC, 5
watt light that is embedded in the bellows, a push
button switch that is closed when the door is open, and
a step down transformer that reduces the voltage from
120 Volts to 12 Volts. (See Figure 1-4)
A circuit in the electronic control turns the light off when
the door is left open for more than three minutes.
(See Figure 1-6)
Door Switch Assembly
The door switch assembly, located behind the front
panel, is a safety feature that prevents the washer from
operating when the door is open and locks the door in
the spin cycle. (See Figure 1-5)
Door Lock Assembly
The door lock assembly is made up of a coil, door
switch, switch actuator, locking fork, wax motor,
auxiliary switch and spin lock arm. (See Figure 1-7)
Figure 1-3. Control
Figure 1-4. Drum Light
Figure 1-5. Door Switch
Figure 1-6. Light Control
Drum Light
Door Switch
Drum Light
Control

Section 1 Basic Information
1-7
Door Lock Assembly (Continued)
When a cycle is selected and the start pad is touched,
the control board applies power to the coil. The
magnetic field of the coil pulls the locking fork down and
tries to pull the contacts of the door lock switch closed.
If the washer door is open, a tab on the switch actuator
prevents the contacts from closing and the locking fork
will not allow the door to be closed until the stop pad
is touched, removing current from the coil. When the
washer door is closed, the door strike pivots the switch
actuator out of the way allowing the magnetic field of
the coil to close the contacts of the door lock switch and
the locking fork locks the door. (See Figure 1-7)
The wax motor and spin lock arm are used to prevent
the door from being opened while the spin basket is still
spinning. Power is applied to the wax motor when the
washer is in spin. When power is applied to the wax
motor, it expands its piston within 30 to 40 seconds,
driving the spin lock arm between the locking fork and
switch actuator holding the locking fork down. At the
same time, the piston closes the door lock auxiliary
switch allowing the washer to go into spin. When power
is removed from the wax motor, it takes about 90
seconds for the wax motor to cool down and retract the
piston, pulling the spin lock arm back away from the
locking fork and auxiliary switch. This provides enough
time for the spin basket to slow its rotation down to the
wash speed before the door could possibly be opened.
Pressure Switch (Select models)
The pressure switch is mounted to the right side panel
under the top of the washer and controls the water level
in the washer. (See Figure 1-8)
The pressure switch is made up of a single pole double
throw switch, but only contacts 1 and 2 are used. The
contacts are controlled by a bellow inside a sealed
chamber. The chamber is connected by a hose to the
air bell located at the bottom of the washer attached to
the drain boot. L1 power is applied to the pressure
switch by the control. If the water level is below 1/2
inch from the bottom of the spin basket, contacts 1 to 2
of the pressure switch close, applying power to one side
of the (3) solenoids of the water valve assembly. The
other side of the solenoids is connected to neutral by a
relay contacts on the control board. When the cycle calls
for water, depending on the water temperature selected
and the increment of the cycle, the control board
connects one or two of three the solenoid coils to neutral
activating the water valve solenoids. When the corrected
water level is reached contacts 1 and 2 open, signaling
the control to remove neutral from the solenoids.
Figure 1-7. Door Lock Assembly
Figure 1-8. Pressure Sensor
Locking Fork
Auxiliary Contacts
Switch Actuator Spin Lock Arm
Pressure Sensor
Coil
Contact

Section 1 Basic Information
1-8
Electronic Water Level Sensor
The electronic water level sensor is mounted to the right
side panel under the top of the washer and controls the
water level in the washer. (See Figure 1-9)
The electronic water level sensor is made up of an
electronic board and a bellow inside a sealed chamber.
The chamber is connected by a hose to the air bell
located at the bottom of the washer attached to the drain
boot. The electronic board reads the pressure in the
bellow and converts it into an electronic signal. This sig-
nal is then sent to the control board which governs the
incoming water by connecting or disconnecting a neutral
line to the water solenoids.
Water Inlet Valve Assembly
The water inlet valve assembly is made up of a plastic
housing, 2 tubes, which the inlet water hoses are
connected to, 3 solenoids and a positive thermal sensor
The hot solenoid is connected to the incoming hot water.
The wash and bleach solenoids share a common input
cavity that is connected to the cold water supply.
(See Figure 1-11)
The hot and wash solenoids share a common output
cavity, with the bleach solenoid having a separate output
cavity. (See Figure 1-12)
Water Valve Operation
The (3) inlet solenoid valves are identical in construction
and operation. The valve body provides an air passage
with a large orifice and seat where the water can be
stopped. The outlet of the valve body empties into a
chamber. A moveable rubber diaphragm operates
against the valve seat to start and stop the flow of water.
The diaphragm is operated by water pressure. It has a
small bleed orifice outside the seat contact area, and a
large main orifice at its center. The armature of the
solenoid serves to open and close the main orifice.
The armature operates within a closed metal tube (valve
guide) which is sealed by the outer edge of the
diaphragm to the valve body. A coil spring holds the
armature down against the diaphragm main orifice when
the solenoid is not energized.
Figure 1-9. Water Level Sensor
Figure 1-10. Inlet Water Valves
Figure 1-11. Water Valve Inlet
Figure 1-12. Water Valve Outlet
Hot
Wash
Bleach
Electronic Water
Level Sensor

Section 1 Basic Information
1-9
The following line drawings and text explains basic valve
operation.
When the valve is in a closed position, the solenoid is not
energized. Water has bled through the diaphragm bleed
orifice placing incoming line pressure on top of the
diaphragm. The bottom of the diaphragm is essentially
at atmospheric pressure (open to the outlet) and the
pressure differential holds the valve shut.
When the solenoid is energized, the resulting magnetic
field pulls the armature up into the valve guide. The
armature spring is compressed by this action. When the
armature moves up, it allows the water on the top of the
diaphragm to drain through the main orifice.
The diaphragm bleed orifice is much smaller than the
main orifice and will not admit enough water to maintain
pressure on the top side of the diaphragm. Thus, as the
pressure on the top of the diaphragm is reduced to
almost zero, pressure on the bottom lifts the diaphragm
off the valve seat, allowing a full flow of water.
When the solenoid is de-energized, the armature drops
down, closing the diaphragm main orifice. Water
continues to flow through the diaphragm bleed orifice,
equalizing the pressure and allowing the spring to push
the diaphragm down against the valve seat.
Figure 1-13.
Figure 1-14.
Figure 1-15.
Figure 1-16.
Water Valve Closed
Armature
Armature
Spring
Valve
Guide
Diaphram
Diaphram
Main Diaphram
Orifice
Bleed
Orifice
Solenoid
Water Valve Open and Diaphragm Up
Water Valve Closing
Solenoid Activated

Section 1 Basic Information
1-10
Water Temperature
When AUTO TEMP switch is set to HOT/COLD in the wash
cycle, the hot solenoid is activated and the bleach
solenoid is deactivated for all except the last fill in rinse.
For the last rinse fill, the wash and bleach solenoids are
activated. When AUTO TEMP switch is set to WARM/
COLD in the wash cycle, the hot and wash solenoids are
activated and the Bleach solenoid is deactivated, for all
except the last fill in rinse. For the last rinse fill, the
wash and bleach solenoids are activated. When the
AUTO TEMP switch is set to WARM/WARM in the wash
cycle, the hot and wash solenoids are activated and the
Bleach solenoid is deactivated for all except the last fill in
rinse. For the last rinse fill, the hot and bleach solenoids
are activated. When the AUTO TEMP switch is set to
COLD/COLD, the wash solenoid is activated and the hot
solenoid cycles to warm the water to 65°. For the last
rinse fill, the wash and bleach solenoids are activated.
When the TEMP switch is set to COLD/COLD in the wash
cycle, the wash solenoid is activated and the bleach
solenoid is deactivated for all except the last fill in rinse.
For the last rinse fill, the wash and bleach solenoids are
activated.
Auto Temp System
The auto temp system controls the minimum temperature
of the cold water setting (approximately 65°F.) and the
temperature of the warm and hot water setting
(approximately 90°F and 120°F). On select models
with a sanitary wash cycle, when the control is set to
sanitary wash, the water temperature is raised to 152°F
in the wash cycle. The auto temp system is made up of
the control board and a positive thermal sensor mounted
in the water inlet valve assembly. On select models, a
positive thermal sensor (drum sensor), a heater control
board, and a 1000 watt heating element located in the
bottom rear of the drum are added to auto temp system.
If the hot water supply in the house is below the auto
temp setting, the drum heater heats the water in the
wash cycle. (See Figure 1-20)
When a warm or hot temperature is selected in the wash
cycle, the control board connects the hot water solenoid
to neutral and cycles the center cold water solenoid off
and on to regulate the temperature. When a cold
temperature is selected, the control board connects the
center cold water solenoid to neutral and cycles the hot
water solenoid off and on to regulate the temperature.
When a warm rinse is selected for the final rinse, the
control connects the outside cold solenoid to neutral
and cycles the hot solenoid.
Figure 1-17. Auto Temp Sensor Location
Figure 1-18. Positive Thermal Sensor
Figure 1-19.
Figure 1-20.
+T NTC
J11
C6.1
C6.2
C6.3
C6.4
C6.5
AQUA
YEL
PURP
TAN
GRAY
DRUM WATER
HEATER
WHT/RED
BLK/WHT
J3
C3.3
C3.3
C3.2
C3.1
C3.1
J2
J1 C2.2
C2.1
HEATER CONTROL BOARD
NL1
Auto Temp
Sensor
Heater
Control
Board

Section 1 Basic Information
1-11
Automatic Dispenser
The automatic dispenser for detergent, liquid bleach and
fabric softener system is made up of the dispenser cavity,
and a removable drawer with three cavities: one for
detergent, one for bleach and one for fabric softener.
A plastic conveyer is snapped to the bottom of the drawer
to direct the outputs from the bleach and softener
chambers to the dispenser housing outlet channel. This
prevents the mixtures from coming out the front of the
drawer. (See Figure 1-21 & 1-22)
The 2 outlets of the water inlet valve assembly are
inserted into the rear of the automatic dispenser. During
the fill cycles, water is directed into the top of the cavity
through 2 inlets. The inlet on the right, as viewed from
the front of washer, is connected to the combination
output of the hot water solenoid and the center cold
water solenoid.
The inlet on the left, as viewed from the front of the
washer, is connected to the cold water solenoid.
In the fill cycle, water enters into the top of cavity and is
directed across the top of the cavity by 4 channels: the
dispenser bypass channel, the detergent channel, bleach
channel and the fabric softener channel. The channel that
receives the water is determined by which inlet supplies
the water or if both inlets supply the water.
(See Figure 1-23)
The dispenser advanced rinsing technology channel
receives water whenever the inlet on the right, as viewed
from the front of the washer, is activated.
(See Figure 1-24)
Figure 1-21.
Figure 1-22.
Figure 1-23.
Figure 1-24.

Section 1 Basic Information
1-12
This path allows the water to bypass the dispenser
drawer and enter the tub by the advanced rinsing
technology hose connected between the cavity and the
bellows. (See Figure 1-25)
The detergent dispenser channel receives water from the
right-hand input, as viewed from the front of the washer.
The detergent channel forms a loop that allows the water
to pass over the detergent section of the drawer.
(See Figure 1-26)
Figure 1-25.
Figure 1-26.
Figure 1-27.
As the water pass over the detergent section, holes in
the cavity allows some of the water to enter and flush
the detergent cavity. (See Figure 1-27)
Since the flow of the incoming water is more than the
holes can dispense, the excess water backs up into a
channel across the rear of the dispenser.
(See Figure 1-28)
Figure 1-28.
Water in this channel and the mixture from the detergent
drawer flow into the tub through the large hose at the
rear of the dispenser. (See Figure 1-29)
Figure 1-29.

Section 1 Basic Information
1-13
Detergent is dispensed at the start of the cycle, but
bleach and fabric softener are not dispensed until later
in the cycle. The bleach and softener cavities in the
drawer have tubes molded into the bottom of them.
These tubes allow bleach or fabric softener to be added
to their cavity without being dispensed as long as the
liquid is below the top of the tubes. At the proper time
in the cycle when bleach or fabric softener is to be
dispensed, water is added to the cavity. This raises the
mixture above the top of the tube and the bleach or
fabric softener starts flowing into the tub.
To allow the cavities to empty, the cover of the detergent
drawer cover has tubes molded into it that fit over the
tubes in the cavities. (See Figure 1-30 & 1-31)
These tubes are larger than the tubes in the cavity and
are designed to fit over the tubes, but not touch the bot-
tom of the cavity when the cover is installed. When water
is added to either the bleach or fabric softener liquid, the
mixture level rises between the tubes above the tubes in
the cavity and flows into the washer tub. Since the end
of the tube on the insert does not touch the bottom of
the cavity, a siphoning action will occur when the
solenoid activates and allows water into the cavity. The
added water creates an “overfill” condition and starts the
siphoning. The cavity will empty itself when the water is
turned off by the solenoid. (See Figure 1-31)
The bleach dispenser channel receives water from the
left-hand input, as viewed from the front of the washer.
The bleach channel forms a path, that allows the water
to pass over the bleach cavity section of the cavity.
(See Figure 1-32)
As the water passes over the bleach section, holes in
the cavity allow some of the water to enter and mix with
the bleach. This raises the mixture level above the tubes
in the drawer bleach cavity allowing the mixture to flow
into the tub. (See Figure 1-33)
Like the detergent channel, the flow of the incoming
water is more than the holes can dispense allowing the
excess water to backup into the channel across the rear
of the dispenser and flow into the tub.
Figure 1-30.
Figure 1-32.
Figure 1-33 .
Figure 1-31.

Section 1 Basic Information
1-14
For water to enter the fabric softener channel, both the
left and right inlets must be activated. As the water from
the left inlet pass over the channel, it collides with the
water from the right inlet. This collision changes the
water path directing it to the front of the cavity and into
the fabric softener channel. The fabric softener channel
forms a loop that allows the water to pass over the fabric
softener cavity section of the drawer.
(See Figure 1-34 & 1-35)
As the water passes over the fabric softener section,
holes in the cavity allow some of the water to enter and
mix with the fabric softener. This raises the mixture level
above the tubes in the drawer fabric softener cavity
allowing the mixture to flow into the tub. Like the
detergent channel, the flow of the incoming water is
more than the holes can dispense, allowing the excess
water to backup into the channel across the rear of the
dispenser and flow into the tub.
Drain Pump
The drain pump is mounted to the bottom plate of the
washer behind the access panel. It operates on 120
VAC and is controlled by the control board and pressure
switch. The pump out specifications of the drain pump
vary from 12 G.P.M. with a 3 foot standpipe height to 5
G.P.M. with a 8 foot standpipe height. (See Figure 1-36)
Motor
The motor is mounted to the bottom of the outer tub.
The motor is an induction, three phase AC motor that
varies speeds when the voltage from the speed control
board varies in frequency and amount. (See Figure 1-37)
The motor has a tachogenerator that inputs the speed of
the motor to the speed control board.
Figure 1-34.
Figure 1-35.
Figure 1-36.
Figure 1-37.

Section 1 Basic Information
1-15
Speed Control
The speed control board is mounted to the base plate of
the washer in the left rear corner of the washer. The
speed control board controls the following operations:
1. The speed of the drive motor by converting input
line to neutral single phase 60 Hertz voltage, to a
varying frequency, three phase output voltage from
zero to 300 VAC. By varying the amount, frequency,
and polarity of the voltage and comparing the input
from the tachogenerator on the drive motor, the
speed control board can operate the drive motor at a
pre programmed speed and direction.
2. The balance of the load in the washer during the
spin cycle by converting the sine wave from the
tachogenerator to square waves and comparing the
distance between the square waves.
Figure 1-39.
Spin Basket
Outer Tub Rear
Outer Tub Front
Bellows (Door Boot)
Retaining Spring
Bellows
The bellows is a rubber sleeve that seals the suspended
outer tub to the stationary cabinet front at the tub
opening. Its purpose is to provide a water tight opening
into the tub that can be sealed by the cabinet door, yet
allow flexibility for the oscillation of the tub during the
wash and spin cycles.
Outer Tub Assembly
The outer tub assembly is supported by two suspension
springs and stabilized by two air shock assemblies. A
cement counter weight mounted to the front of the outer
tub. Another weight is molded into the rear half of the
outer tub. These counterweights prevent excessive
oscillation of the entire suspended assembly during an
unbalanced spin cycle.
Spin Basket Assembly
The spin basket is constructed of stainless steel. The
circumference of the basket is perforated to allow water
to flow through it as it revolves. A heavy steel shaft is
pressed into the spin basket support which is then bolted
to the basket. The spin basket assembly is entirely
supported by two ball bearing assemblies pressed into
the rear of the outer tub.
A large drive pulley is mounted to the free end of the
shaft that extends through the rear of the outer tub.
There are three plastic vanes mounted to the spin basket
to aid in the washing action during the wash cycle. The
rotation of the spin basket provides both the washing
action during the wash cycle and water extraction during
the spin cycle.
Figure 1-38. Speed Control
Tub Construction
The front loading tumble action clothes washer consists
of a perforated, cylindrical spin basket suspended
horizontally on its axis within a larger solid cylindrical tub.
This assembly is suspended by springs within a four
piece steel cabinet. A see through door and a flexible
bellows (seal) provides access for loading and unloading.
Cabinet
The cabinet is made of heavy steel in a four piece design.
The sides and rear are Tog-l-loked at the rear corners
and base. The rear of the cabinet is galvanized steel with
an access panel.
Front Panel and Door Assembly
The front panel is attached with screws to the console
mounting brace and base plate.

Section 1 Basic Information
1-16
Major Appliance Warranty Information
Your appliance is covered by a one year limited warranty. For one year from your original date of
purchase, Electrolux will pay all costs for repairing or replacing any parts of this appliance that prove
to be defective in materials or workmanship when such appliance is installed, used and maintained in
accordance with the provided instructions.
This warranty does not cover the following:
1. Products with original serial numbers that have been removed, altered or cannot be readily determined.
2. Product that has been transferred from its original owner to another party or removed outside the USA or
Canada.
3. Rust on the interior or exterior of the unit.
4. Products purchased “as-is” are not covered by this warranty.
5. Food loss due to any refrigerator or freezer failures.
6. Products used in a commercial setting.
7. Service calls which do not involve malfunction or defects in materials or workmanship, or for appliances
not in ordinary household use or used other than in accordance with the provided instructions.
8. Service calls to correct the installation of your appliance or to instruct you how to use your appliance.
9. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves,
etc., which are not a part of the appliance when it is shipped from the factory.
10. Service calls to repair or replace appliance light bulbs, air filters, water filters, other consumables, or
knobs, handles, or other cosmetic parts.
11. Surcharges including, but not limited to, any after hour, weekend, or holiday service calls, tolls, ferry trip
charges, or mileage expense for service calls to remote areas, including the state of Alaska.
12. Damages to the finish of appliance or home incurred during installation, including but not limited to
floors, cabinets, walls, etc.
13. Damages caused by: services performed by unauthorized service companies; use of parts other than
genuine Electrolux parts or parts obtained from persons other than authorized service companies; or
external causes such as abuse, misuse, inadequate power supply, accidents, fires, or acts of God.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
CUSTOMER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT
REPAIR OR REPLACEMENT AS PROVIDED HEREIN. CLAIMS BASED ON IMPLIED WARRANTIES,
INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE
LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW, BUT NOT LESS THAN ONE YEAR.
ELECTROLUX SHALL NOT BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS
PROPERTY DAMAGE AND INCIDENTAL EXPENSES RESULTING FROM ANY BREACH OF THIS WRITTEN
LIMITED WARRANTY OR ANY IMPLIED WARRANTY. SOME STATES AND PROVINCES DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE
DURATION OF IMPLIED WARRANTIES, SO THESE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO
YOU. THIS WRITTEN WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER
RIGHTS THAT VARY FROM STATE TO STATE.
Keep your receipt, delivery slip, or some other appropriate payment record to establish the warranty period
should service be required. If service is performed, it is in your best interest to obtain and keep all receipts.
Service under this warranty must be obtained by contacting Electrolux at the addresses or phone
numbers below.
This warranty only applies in the USA and Canada. In the USA, your appliance is warranted by Electrolux Major Appliances
North America, a division of Electrolux Home Products, Inc. In Canada, your appliance is warranted by Electrolux Canada
Corp. Electrolux authorizes no person to change or add to any obligations under this warranty. Obligations for service and
parts under this warranty must be performed by Electrolux or an authorized service company. Product features or
specifications as described or illustrated are subject to change without notice.
Exclusions
If You Need
Service
USA
1.800.944.9044
Electrolux Major Appliances
North America
P.O. Box 212378
Augusta, GA 30907
Canada
1.800.668.4606
Electrolux Canada Corp.
5855 Terry Fox Way
Mississauga, Ontario, Canada
L5V 3E4

Section 2 Installation Information
2-1
To reduce the risk of fire, electrical shock, or injury when using a Frigidaire Affinity Washer, follow basic safety
precautions including the following:
- Read all instructions before operating the washer.
- Before performing any type of service or installation, make sure that electric power to the washer is
disconnected.
- To avoid the possibility of explosion or fire, do not store or use combustible, flammable, or explosive liquids
or vapors (such as gasoline) inside or in the vicinity of this or any other appliance.
- This appliance is equipped with a three-prong grounding plug for protection against possible electric shock
hazards. Plug it only into a dedicated, grounded electrical outlet. When only a standard two-prong electrical
outlet is available, the customer must have it replaced with a dedicated, properly grounded three-prong
electrical outlet before using this Appliance.
Do not under any circumstances, cut or remove the third (ground) prong from the power cord.
Do not use an adapter plug.
Do not use an extension cord.
Do not use a power cord that is frayed or damaged.
The use of a ground fault interrupter (GFI) is not recommended.
- Do not install or use a damaged appliance. If you receive a damaged appliance, immediately contact your
dealer or builder.
- The installer must show the customer the location of the power plug so that they know where and how to
disconnect power to the washer.
- The customer should not install, repair or replace any part of the washer unless specifically recommended in
the literature accompanying it. A qualified service technician should perform all other service.
WARNING
Destroy carton, plastic bags, and any exterior wrapping material immediately after the Washer is unpacked.
Children should never use these items for play. Cartons covered with rugs, bedspreads, plastic sheets or stretch
wrap may become air tight chambers and can quickly cause suffocation.
Keep laundry products out of children’s reach. To prevent personal injury, observe all warnings on product labels.
Cut Hazard. To prevent serious injury from sharp edges, wear work gloves when handling, unpacking or
disassembling unit.
WARNING
Electrolux cannot be held responsible for damage to property or injury to persons caused by failure to comply with
the installation, maintenance and safety instructions contained in this Service Manual.
WARNING
WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your building.
• Clear the room, building or area of all occupants.
• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire department.
DANGER

Section 2 Installation Information
2-2
Pre-Installation Requirements
Tools and materials needed for installation:
• Channel lock adjustable pliers
• Phillips, straight, & square bit screw-drivers
• Adjustable wrench
• 10 mm socket with ratchet
• Carpenter’s level
Electrical System Requirements
Circuit - Individual, properly polarized and grounded 15
amp. branch circuit fused with 15 amp. time delay fuse
or circuit breaker.
Power Supply - 2 wire, with ground, 120 volt single
phase, 60 Hz, alternating current.
Outlet Receptacle - Properly grounded 3-prong
receptacle to be located so the power supply cord is
accessible when the washer is in an installed position.
Grounding Type
Wall Receptacle
Power Cord with
3- Prong Grounded Plug
DO NOT, under any
circumstances, cut,
remove, or bypass the
grounding plug.
Figure 2-1. Electrical Connection
Because of potentially inconsistent voltage capabilities,
the use of this washer with power created by gas
powered generators, solar powered generators, wind
powered generators or any other generator other than
the local utility company is not recommended.
GFI (Ground Fault Interrupter) receptacle is not
required.

NOTE
Improper connection of the equipment grounding
conductor can result in a risk of electrical shock.
Check with a licensed electrician if you are in doubt as
to whether the appliance is properly grounded.
WARNING
Grounding Requirements
1. The washer MUST be grounded. In the event of
malfunction or breakdown, grounding will reduce the
risk of electrical shock by a path of least resistance
for electrical current.
2. This washer is equipped with a power supply cord
having an equipment-grounding conductor and a
grounding plug, the plug MUST be plugged into an
appropriate, copper wired receptacle that is properly
installed and grounded in accordance with all local
codes and ordinances or in the absence of local
codes, with the National Electrical Codes, ANSI/
NFPA 70 (latest edition). If in doubt, call a licensed
electrician. DO NOT cut off or alter the grounding
prong on the power supply cord. In situations where
a two-slot receptacle is present, it is the owner’s
responsibility to have a licensed electrician replace
it with a properly grounded three prong grounding
type receptacle.