Frigidaire ATF6000FS1 User manual

Full Size Tumble Action Washers
Before beginning installation, carefully read these instructions. This will simpfify the
installation and ensure the washer is installed correctly and safely. Leave these instructions
near the washer after installation for future reference.
NOTE: The electrical service to the washer must conform with local codes and ordinances
and the latest edition of the National Electrical Code, ANS!/NFPA 70.
For your safety the information in
this manual must be followed to minimize the risk
of fire or explosion or to prevent property damage,
personal injury or loss of life.
- Do not store or use gasoline or other flammable
vapors and liquid in the vicinity of this or any
other appliance.
-WHAT TO DO IF YOU SMELL GAS
•Do not try to light any appliance.
•Do not touch any electrical switch; do not
use any phone in your building.
•Clear the room, building or area of all
occupants.
•Immediately call your gas supplier from a
neighbor's phone. Follow the gas suppliers
instructions.
•If you cannot reach your gas supplier, call
the fire department.
Installation and service must be performed by a
qualified installer, service agency or the gas
supplier.
Printed in U.S.A.
Contents
S UBJECT PAGE
Pre-lnstallation Requirements 2
Electrical Requirements 2
Grounding Requirements 2
Water Supply Requirements 2
Drain Requirements 2
Rough-In Dimensions 3
Location Of Your Washer 4
Unpacking 4-5
Installation B-6
Replacement Parts 6
WN 134905800(0707)

PRE-INSTALLAT!ON REQUIREMENTS
Tools Required for Installation:
I. Phillips screwdriver
2. 10 mm socketwith ratchet.
3. Channel-lock adjustable pliers.
4. Carpenter's level.
absence of local codes, with the National Electrical
Codes, ANSI/NFPA 70 (latest edition). If in doubt,
call a licensed electrician. DO NOTcut off or alter
the grounding prong on the power supply cord. In
situations where a two-slot receptacle is present,
it is the owner's responsibility to have a licensed
electrician replace it with a properly grounded
three prong grounding type receptacle.
ELECTRICAL REQUIREMENTS
CIRCUIT- Individual, properly polarized and grounded
15 amp. branch circuit fused with 15 amp. time delay
fuse or circuit breaker.
POWER SUPPLY- 2 wire, with ground, 120 volt, single
phase, 60 Hz, Alternating Current. NOTE: Because of
potential inconsistent voltage capabilities, the useof this
washer with power created by gas powered generators,
solar powered generators, wind powered generators or
any other generator other than the local utility company
isnot recommended.
OUTLET RECEPTACLE - Properly grounded 3-prong
receptacle to be located so the power supply cord is
accessible when the washer is in an installed position.
NOTE: GFI (Ground Fault Interrupter) receptacle is not
required.
GROUNDING REQUIREMENTS
Improper connection of the equipment
grounding conductor can result in a risk of electrical
shock. Check with a licensed electrician if you are in
doubt asto whether the appliance isproperly grounded.
.The washer MUST be grounded. In the event of
malfunction or breakdown, grounding will reduce
the risk of electrical shock by a path of least
resistance for electrical current.
.Sinceyour washer isequipped with a power supply
cord having an equipment-grounding conductor
and a grounding plug, the plug MUSTbe plugged
into an appropriate, copper wired receptacle that
is properly installed and grounded in accordance
with all local codes and ordinances or in the
WATER SUPPLY REQUIREMENTS
Hot and cold water faucets MUST be installed within
42 inches (107 cm) of your washer's water inlet. The
faucets MUST be 3/4 inch (1.9 cm) garden hose type
so inlet hoses can be connected. Water pressure MUST
be between 30 and 120 pounds per squareinch (maximum
unbalance pressure, hot vs. cold, 10 psi.) Your water
department can advise you of your water pressure.
DRAIN REQUIREMENTS
I. Drain capable of eliminating 17 gals (64.3 L) per
minute.
2. A standpipe diameter of 1-1/4 in. (3.18 cm)
minimum.
3. The standpipe height above the floor should be:
Minimum height: 24 in. (61 cm)
Maximum height: 96 in. (244cm)
BACK II
r
96 in.
(244 cm)
Max.
iiiiiiiiii
iiiiiiiiii
..........24 in.
(61 cm)
_ MJn.
!!!!!!!!!!i 1
NOTE:
Drain hose attached to the washer can reach a 90
in. (229 cm) high standpipe. For higher standpipe,
use hose P/N 134359410, available from an
authorized parts distributor.

23¾"
(60.33)
ROUGH-iN DiMENSiONS
24"
(60.96)
inches(cm)
NOTE:
inches(¢m)
25/8"
(6.67)
_ - siDE
22" ,
(55.88)
255/8"
(65.09)
281/4"
(71.76)
35/8"
_(9.21 )
For pedestal installations, see additional installation instructions included with the pedestal.
For stacking installations, see additional installtion instructions included with the stacking kit.
For under counter installations, no special top is required.
27"
"1 (68.58)
_- 2½" (17.15)
____(6.35) 0 O0
_ ./-----_
33½"
:85.09)
BACK
i -- w
4 23"
(58.42)
27"
(68.58)
9

LOCATION OF YOUR WASHER
DO NOT INSTALL YOUR WASHER:
I. Inan area exposed to dripping water or outside weather conditions. The ambient temperature should never be below 60 ° F
(15.6 ° C) for proper washer (detergent breakdown) operation.
2. In an area where it will come in contact with curtains or drapes.
3. In an area (garage or garage-type building) where gasoline of other flammables are kept or stored (including automobiles).
4. On carpet. Floor MUST be solid with a maximum slope of 1/2 in. per foot (1.27 cm per 30.5 cm). To ensure vibration or
movement does not occur, reinforcement of the floor may be necessary.
IMPORTANT
MINIMUM INSTALLATION CLEARANCES
When installed in alcove or closet:
Sides, Rear = 0 in. (0 cm)
Top = 0 in. (0 cm)
When installed in closet: Front = I in. (2.54 cm)
Closet door ventilation required: 2 Iouvered openings each 60 in2(387 cm2),3 in. (7.6 cm) from top and bottom of door.
UNPACKING
1. Cut the shipping carton along the dotted line along the bottom. Removethe carton.
2. Using a rug, blanket or piece of cardboard to protect the floor, lay the washer on it's back.
3. Remove and savethe styrofoam base and shipping plug.
Shipping
Base Plug

4. Carefully return the washer to an
upright position.
5. Carefully move the washer to within
4 feet (122cm) of the final location.
6. Remove the following from the back
panel of the washer:
4 shipping bolts,
4 spacers,
I metal "P" clamp,
2 hose clips.
7. Removethe 4 plugs from the literature
pack located in the drum and install
them in the holes vacated by the
packaging spacers.
NOTE: If the washer isto be
transported at a later date,
the shipping support
hardware must be reinstalled
Remove:
metal "P" clamp
4 shipping_bbolts,
4 spacers.
to prevent shipping damage.
INSTALLATION
Leveling the Washer
Excessivenoise and vibration can be prevented by properly
leveling the washen
For free standinq installation and with the washer in it's
final position, place a level on top of the washer. Adjust
the leveling legs so the washer is level front-to-rear and
side-to-side, and stable comer-to-comer.
Pressdown on alternate corners and sides and feel for the
slightest movement. Adjust the appropriate leg so the
washer is SOLID on the floor on ALLfour legs. Keep the
leveling leg extension at a minimum for best performance
of the washer.
.
Washer Connections
I. Run some water from the hot and cold
faucets to flush the water lines and
remove particles that might clog up
the water valve screens.
2. Remove the inlet hoses and rubber
washers from the plastic bag located
in the drum of the washer and install
the rubber washers in each end of the
inlet hoses.
3. Carefully connect the inlet hose marked "HOT" to the
outside "H" outlet of the water valve. Tighten by hand,
then tighten another 2/3 turn with pliers. Carefully connect
the other inlet hose to the inside "C" outlet of the water
valve. Tighten by hand, then tighten another 2/3 turn with
pliers. Do not crossthread or over-tighten these
connections.
4. Connect the inlet hose ends to the HOT and COLD water
faucets tightly by hand, then tighten another 2/3 turn with
pliers. Turn the water on and check for leaks.
NOTE: Use only new hoses.
2. For pedestal installations, See additional installation
instructions included with the pedestal.

!iNSTALLATiON (CON'T)
Attach drain hose hanger (shipped in washer tub) to
drain hose.
Place the hook end of the drain hose in the drain
opening. Secure the drain hose with the cable tie
(provided in the enclosure package) to the standpipe,
inlet hose, laundry tub, etc. so the hose does not pull
out from the force of the water.
7. Plug the power cord into a grounded outlet.
NOTE; Check to ensure the power isoff at a circuit breakedfuse box before
plugging the power cord into an outlet.
8. Turn on the power at a circuit breaker/fuse box.
9. Readthe Operating Instructions and Owner's Guide provided with the washer.
They contain valuable and helpful information that will save you time and
money.
10. Runthe washer through a complete cycle. Check for water leaks and proper
operation.
Cable Tie
1I. If your washer does not operate, please review the "Avoid ServiceChecklist"
in your Owner's Guide before calling for service.
12. Placethese instructions in a location near the washer for future reference.
\
U
Cable Tie
Cable Tie
NOTE: A wiring diagram and technical data sheet are located in an envelope
attached to the left hand side panel on the inside of the washer.
Pedestal
A pedestal accessory,MadelNa. APWD15W(White), APWD15GB (Glacier
Blue),APWD15P(Platinum)andAPWD15E(Black), specifically designed
for this washer may be used when elevating the washer for ease of use.
Failure to use accessories certified by the manufacturer could result in
personal injury, property damage or damage to the washer.
REPLACEMENT PARTS
If replacements parts are needed for your washeB contact the source where you
purchased your washer, call 1-800-944-9044, or visit our website,
www.frigidaire.com for the Frigidaire Company Authorized Parts Distributor
nearest you.
Destroy the carton and plastic bags after the washer is unpacked.
Children might use them for play. Cartons covered with rugs, bedspreads, or
plasticsheetscan become airtight chambers causing suffocation. Placeall materials
in a garbage container or make materials inaccessible to children.
_The instructions in this manual and all other literature included with
this washer are not meant to cover every possible condition and situation that
may occun Good safe practice and caution MUST be applied when installing,
operating and maintaining any appliance.
Maximum benefits and enjoyment are achieved when all the Safety and ]
i
Operating instructions are understood and practiced as a routine with your 1
laundering tasks.