Frigidaire FAHE1011MW User manual

All about the
Installation
of your Washer
Important Safety Instructions..............................2-3
Installation Requirements ...................................4-6
Unpacking Washer.................................................7
Installation Instructions......................................8-9
Accessories.........................................................10
Français..............................................................11
Español ..............................................................21
TABLE OF CONTENTS
137544200A (1207)

2
IMPORTANT SAFETY INSTRUCTIONS
WARNING
WARNING indicates a potentially hazardous situation
which, if not avoided, could result in death or serious
injury.
IMPORTANT
IMPORTANT indicates installation, operation or
maintenance information which is important but not
hazard-related.
DANGER
DANGER indicates an imminently hazardous situation
which, if not avoided, will result in death or serious
injury.
Definitions
This is the safety alert symbol. It is used to alert
you to potential personal injury hazards. Obey all safety
messages that follow this symbol to avoid possible injury
or death.
Shipping Hardware
Foam shipping restraint (inside wash tub)
removed and stored
Shipping bolt (underneath appliance) removed
and stored
Leveling
Washer is level, side-to-side and front-to-back
Cabinet is setting solid on all corners
Water Supply
Use only new hoses and verify rubber sealing
washers are installed
HOT supply is connected to HOT inlet and
COLD supply is connected to COLD inlet
HOT and COLD water supply turned on
No leaks present at water supply connections
or appliance inlet connections -
recheck in 24 hours
Drain
Stand pipe or wall drain height minimum 33”
Drain hose secured in place with cable tie
(shipped in drum)
Electrical Power
House power turned on
Washer plugged in
Final Checks
 Installation Instructions and Use and
Care Guide read thoroughly
Water enters drum when cycle starts with lid
lowered.
Registration card sent in
Installation Checklist
CAUTION
CAUTION indicates a potentially hazardous situation
which, if not avoided, may result in minor or moderate
injury.
WARNING
Please read all instructions before using this washer.
Recognize safety symbols, words and
labels
Safety items throughout this manual are labeled with
a WARNING or CAUTION based on the risk type as
described below:

3
IMPORTANT SAFETY INSTRUCTIONS
ÍNOTE
The electrical service to the washer must conform with
local codes and ordinances and the latest edition of the
National Electrical Code, ANSI/NFPA 70, or in Canada,
the Canadian Electrical Code C22.1 part 1.
ÍNOTE
Hoses are not included with washer purchase. See
“Accessories” section for various inlet hose kits to fit your
specific installation.
WARNING
SUFFOCATION HAZARD
Destroy the carton and plastic bags after the washer is
unpacked. Children might use them for play. Cartons
covered with rugs, bedspreads, or plastic sheets can
become airtight chambers causing suffocation. Place
all materials in a garbage container or make materials
inaccessible to children.
CAUTION
EXCESSIVE WEIGHT HAZARD
To avoid back or other injury, have more than one
person move or lift the washer.
WARNING
FIRE HAZARD
For your safety the information in this manual must be
followed to minimize the risk of fire or explosion or to
prevent property damage, personal injury or loss of life.
Do not store or use gasoline or other flammable vapors
and liquids in the vicinity of this or any other appliance.
IMPORTANT
The instructions in this manual and all other literature
included with this washer are not meant to cover
every possible condition and situation that may occur.
Good safe practice and caution MUST be applied when
installing, operating and maintaining any appliance.
Maximum benefits and enjoyment are achieved
when all the Safety and Operating Instructions are
understood and practiced as a routine with your
laundering tasks.
Inlet hose (x2)
Tools and materials needed for installation:
Save these instructions
for future reference.
Adjustable
pliers
Adjustable
wrench
3/8” or 10 mm
box wrench
OR OR AND AND
Ratchet and
socket set
Carpenter’s level

4
INSTALLATION REQUIREMENTS
ÍNOTE
Because of potentially inconsistent voltage capabilities,
the use of this washer with power created by gas
powered generators, solar powered generators, wind
powered generators or any other generator other than
the local utility company is not recommended.
WARNING
ELECTRICAL SHOCK HAZARD
Improper connection of the equipment grounding
conductor can result in a risk of electrical shock. Check
with a licensed electrician if you are in doubt as to
whether the appliance is properly grounded.
ÍNOTE
GFI (Ground Fault Interrupter) receptacle is not
required.
CIRCUIT - Individual, properly polarized and grounded
15 amp. branch circuit fused with 15 amp. time delay
fuse or circuit breaker.
POWER SUPPLY - 2 wire, with ground, 120 volt single
phase, 60 Hz, Alternating Current.
OUTLET RECEPTACLE - Properly grounded 3-prong
receptacle to be located so the power supply cord is
accessible when the washer is in an installed position.
Grounding type
Grounding type
wa
wa
ll receptacl
ll receptacle
Po
Po
wer cord with
wer cord with
3-prong
3-prong
gr
gr
ounded plug
ounded plug
Do not,
Do not,
under
under
an
an
y cir
y cir
cumstances,
cumstances,
cut,
cut,
remo
remo
ve
ve,
or b
or b
ypass th
ypass the
gr
gr
ounding pr
ounding pr
ong.
ong.
Water supply requirements
Hot and cold water faucets MUST be 3/4 inch (1.9 cm)
with threading for laundry hose connection. Water
pressure MUST be between 30 and 120 psi. Pressure
difference between hot and cold cannot be more than 10
psi. Your water department can advise you of your water
pressure.
Ground requirementsElectrical system requirements
1The washer MUST be grounded. In the event of
malfunction or breakdown, grounding will reduce
the risk of electrical shock by a path of least
resistance for electrical current.
2Since your washer is equipped with a power supply
cord having an equipment-grounding conductor
and a grounding plug, the plug MUST be plugged
into an appropriate, copper wired receptacle that is
properly installed and grounded in accordance with
all local codes and ordinances or in the absence
of local codes, with the National Electrical Codes,
ANSI/NFPA 70 (latest edition). If in doubt, call a
licensed electrician. DO NOT cut off or alter the
grounding prong on the power supply cord. In
situations where a two-slot receptacle is present,
it is the owner’s responsibility to have a licensed
electrician replace it with a properly grounded three
prong grounding type receptacle.

5
INSTALLATION REQUIREMENTS
ÍNOTE
For installations requiring a longer drain hose, have a
qualified technician install a longer drain hose (according
to your model number) available from an authorized parts
distributor. For drain systems in the floor, install a syphon
break kit available from your local hardware store.
Installation in a Recess or Closet
If washer and dryer are installed in the same closet,
door ventilation is required: A minimum of 120 square
inches (774.2 cm²) of opening, equally divided at the top
and bottom of the door, is required. Louvered openings
should be located 3 inches (7.6 cm) from bottom and
top of door. Air openings are required to be unobstructed
when a door is installed. A louvered door with equivalent
air openings for the full length of the door is acceptable.
60 sq. in.
(387.1cm²)
3”
(7.6cm)
60 sq. in.
(387.1cm²)
3”
(7.6cm)
closet door
Drain system requirements
1Drain capable of eliminating 17 gals (64.3 L) per
minute.
2A standpipe diameter of 1-1/4 in. (3.18 cm)
minimum.
3The standpipe height above the floor should be:
Minimum height: 33 in. (84 cm)
Maximum height: 96 in. (244 cm)
96”
(244cm)
max.
33”
(84cm)
min.

6
IMPORTANT
DO NOT INSTALL YOUR WASHER:
1In an area exposed to dripping water or outside
weather conditions. The ambient temperature
should never be below 60° F (15.6° C) to
maximize detergent effectiveness.
2In an area (garage or garage-type building)
where gasoline or other flammables (including
automobiles) are kept or stored.
3On carpet. Floor MUST be solid with a maximum
slope of 1 inch (2.5 cm). To minimize vibration
or movement, reinforcement of the floor may be
necessary.
INSTALLATION REQUIREMENTS
27” (68.5 cm) 29” (73.5 cm)
37”
(94 cm)
12”
(30.5 cm) 43”
(109 cm)
60” (152.5 cm)
to clear open lid
MINIMUM INSTALLATION CLEARANCES - Inches (cm)
SIDES REAR TOP FRONT
Alcove 0” (0 cm) 0” (0 cm)* 23” (58.5 cm) n/a
Closet 0” (0 cm) 0” (0 cm)* 23” (58.5 cm) 1” (2.5 cm)
0”
(0 cm)
0”
(0 cm)
1”
(2.5 cm)
0”
(0 cm)
23”
(58.5 cm)
Washer Dimensions
drain hose reten-
tion clamp on rear
of washer2
water supply
connection on
rear of washer
power cord attachment
location on rear of unit1
1Power supply cord length on gas unit approximately 60 inches (152.5 cm).
2Loose drain hose length beyond clamp approximately 52 inches (132 cm).
Clearance requirements

7
UNPACKING WASHER
WIRE CLIP
PLASTIC
SPACER
SHIPPING
BOLT
PLASTIC
CLAMP
Unpacking Instructions
1. If foam tub block has been removed, reinsert it now
and retape the lid securely.
2. Using a rug, blanket or piece of cardboard to protect
the floor, carefully lay the washer on its left side.
3. Using a ratchet with 3/8” (10 mm) socket, remove the
mechanism shipping bolt and plastic spacer block from
the center of the base.
4. Carefully return the washer to an upright position.
5. Remove the tape holding the lid shut and open the lid.
6. Remove the foam tub block and other tub contents.
7. From the back of the washer, remove the wire
shipping clip securing the drain hose.
8. DO NOT remove the PLASTIC CLAMP which secures
the drain hose to the right side of the washer
backsheet. It helps form a standpipe to prevent water
siphoning.
9. Carefully move the washer to within 4 feet of the final
location for the start of the installation.
ÍNOTE
If the washer is to be transported at a later date, the
tub blocking pad, shipping bolt, and plastic spacer
block should be retained.
IMPORTANT
To prevent vibration, possible machine damage and
maximize performance, the following steps must be
completed.
CAUTION
EXCESSIVE WEIGHT HAZARD
To avoid back or other injury, have more than one
person move or lift the appliance.

8
INSTALLATION INSTRUCTIONS
ÍNOTE
Hoses are not included with washer purchase. See
“Accessories” section for various inlet hose kits to fit
your specific installation.
Leveling your washer
Excessive noise and vibration can be prevented by
properly leveling the washer.
1With the washer within 4 feet (1 m) of its final
location, use a carpenter’s level to level your
washer front-to-back and side-to-side. For front-
to-back leveling, place bottom edge of the level on
the seam between the top panel and side panel.
For side-to-side leveling place the bottom side of
the level flush to the side panel.
2Use adjustable pliers to adjust the leveling legs so
the washer is level front-to-rear and side-to-side,
and stable corner-to-corner.
3Press down on alternate corners and sides and feel
for the slightest movement. Adjust the appropriate
leg(s) so the washer sits solidly on the floor on
ALL four legs. Keep the leveling leg extension at a
minimum for best performance of the washer.
1 Run some water from the hot and cold faucets to
flush the water lines and remove particles that might
clog the water valve screens and to determine which
faucet is hot and which is cold supply.
Connecting inlet water
2 Connect the HOT inlet hose to the HOT inlet
connection on the washer and the COLD inlet hose to
the COLD inlet connection on the washer. Tighten by
hand until snug. Then tighten each supply connection
another 2/3 turn with pliers. Do not cross thread
or over-tighten these connections.
3Connect the HOT inlet hose to the HOT water
supply and the COLD inlet hose to the COLD water
supply. Tighten by hand until snug. Then tighten
each supply connection another 2/3 turn with pliers.
Do not bend, kink or pinch water inlet hoses.
4Turn on the water and check for leaks.
RUBBER WASHERS
MUST BE PRESENT USE ONLY
NEW HOSES
ab
c
d
raise lower
a
ef
g
b
cd
“C”
(COLD)
“H”
(HOT)

9
INSTALLATION INSTRUCTIONS
IMPORTANT
Check to ensure the power is off at a circuit breaker/fuse
box before plugging the power cord into an outlet.
Connecting drain and electrical
CABLE TIE
1Form a “U” shape on the end of the drain hose with the
hose pointed toward the drain. Place the formed end in
a laundry tub or a standpipe and secure with a cable tie
provided in the enclosure package.
2Place the hook end of the drain hose in the drain
opening. Secure the drain hose with the cable tie
(provided in the enclosure package) to the standpipe,
inlet hose, laundry tub, etc. so the hose does not pull
out from the force of the water.
3Plug the power cord into a grounded outlet.
4Turn on the power at the circuit breaker/fuse box.
5Carefully slide the washer to its final position. Recheck
for level and rock corners for stability.
6Read the Use & Care Guide provided with the washer.
It contains valuable and helpful information that will
save you time and money.
7Run the washer through a complete cycle, checking for
water leaks and proper operation.
8If you have any questions during initial operation,
please review the “Avoid Service Checklist” in your Use
& Care Guide before calling for service.
9Place these instructions in a location near the appliance
for future reference.
type
type
Grounding
Grounding
receptacle
receptacle
wa
wa
ll
ll
Po
Po
wer cord
wer cord
with 3-prong
with 3-prong
gr
gr
ounded plug
ounded plug
Do not, under any circumstances,
Do not, under any circumstances,
cut, remove, or bypass the
cut, remove, or bypass the
grounding prong.
grounding prong.
ÍNOTE
The standpipe inside diameter must be 1-1/4” (3.2 cm)
minimum. There must be an air gap around the drain hose in
the standpipe. A snug hose fit can cause a siphoning action.

10
ACCESSORIES
ÍNOTE
A wiring diagram and technical data sheet are located
inside the washer console.
CAUTION
Failure to use accessories manufactured by (or approved
by) the manufacturer could result in personal injury,
property damage or damage to the washer.
WARNING
ELECTRICAL SHOCK HAZARD
Label all wires prior to disconnection when servicing
controls. Wiring errors can cause improper and dangerous
operation. Verify proper operation after servicing.
Replacement parts:
If replacements parts are needed for your washer,
contact the source where you purchased your washer or
refer to your Use and Care Guide for more information.
To remove the console faceplate follow the directions
below:
1. Disconnect washer from electrical source.
2. Remove the hole plugs on the back of the console
housing.
3. Insert a small, straight blade screw drive to gently pry
downward on each faceplate retaining tab.
4. Gently lay the console faceplate forward without
pulling wires to access technical/wiring diagram.
5. When finished with repair, return sheet inside console,
snap faceplate to console housing and reinstall hole
plugs.
MOBILE HOME INSTALLATION KIT
P/N 137067200
Installation in a mobile home requires the use of a
MOBILE HOME INSTALLATION KIT.
INLET HOSE KITS
Please call 866-233-8353 (in Canada, 800-265-8352)
to explore hose kit options that will meet your specific
installation needs.
UNIVERSAL APPLIANCE WRENCH
P/N 137019200
A UNIVERSAL APPLIANCE WRENCH is available to aid in
dryer/washer feet adjustment.
TOUCH UP PAINT PENS*
Classic White Touch Up Pen - P/N 5304468812
*Other colors may be available. Contact the source where you
purchased your washer.
Technical Sheet/Wiring Diagram:
TECH DATA SHEET/
WIRING DIAGRAM