Frog Pool XL Pro User manual

1
Customer Service 800-222-0169
www.kingtechnology.com
POOL FROG XL PRO®
Instruction Manual
For Pools up to 40,000 Gallons
System Includes the
Patented Mineral Pool
Disinfectant
MINERAL
RESERVOIR
CHLORINE
PAC
�
�
®
B R AND
• Lessworkwithnodailydosing.
• Reduceschlorineuseupto50%.*
• Adoptaneasier,morefunpool
 environment.
*Compared to the minimum EPA recommended chlorine level of 1.0 ppm for a stabilized swimming pool.
Adopt A FROG®for
Worry-Free Water!


2
For information on King Technology’s entire product line,
visit our website at www.kingtechnology.com
TABLE OF CONTENTS
POOL FROG® Introduction 3
Swimming Pool Tips 4
Start-up and Operation 5-6
Replacing POOL FROG® Mineral Reservoir 7
Using FROG BAM® 8
Using POOL FROG® Pac 9
Troubleshooting 10
Parts List 11
Replacing Control Dial O-Rings 12
Replacing Cap O-Ring and Knob 12
Winterizing 13
In-line Installation 14
For Proper Performance 15
Warranty 16

3
�
Welcome to easier pool care courtesy of POOL FROG XL PRO®. With POOL
FROG XL PRO®, your pool water will look and feel better without a lot of
work or a lot of chlorine. This system controls bacteria using a combination
of minerals and reduced chlorine levels-up to 50%* less. There are 5 parts
to the POOL FROG XL PRO® System: Two In Ground Cyclers, the POOL
FROG® Mineral Reservoir, FROG BAM® 90-day Algae Preventative and the
POOL FROG® Pac.
Part 1 & 2
POOL FROG XL PRO®Cyclers
The water treatment centers that control the flow of
water through the POOL FROG®Mineral Reservoir in one
and the POOL FROG®Pac in the other.
Part 3
POOL FROG®Mineral Reservoir
Holds the minerals and fits inside the POOL FROG®Mineral
Cycler.
POOL FROG®
Mineral Cycler
For In Ground Pools
up to 40,000
gallons.
POOL FROG®
Chlorine Cycler
Part 4
FROG BAM®
Use with the POOL
FROG XL PRO®System
for an Algae-Protection
Guarantee.
Part 5
POOL FROG®Pac
Pre-filled with chlorine tablets and fits
inside the POOL FROG®Chlorine Cycler.
(POOL FROG® Mineral Reservoir sold inside POOL FROG®Mineral Cycler and separately for replacements.
POOL FROG®Pac and FROG BAM®sold separately.)
*Compared to the minimum EPA recommended chlorine level of 1.0 ppm for a stabilized swimming pool.
POOL
FROG®
THE POOL FROG
®
MINERAL RESERVOIR
MUST BE REPLACED
EVERY SIX MONTHS
OR AFTER ONE POOL
SEASON WHICHEVER
IS SHORTER.
MINERAL
RESERVOIR
CHLORINE
PA C
�
�
PAC 540C
�

4
Swimming Pool Tips
Start-up and Yearly Maintenance
1.
Make sure the pool has adequate circulation. The pool
water must completely circulate through the pump and
filter at least 1 to 2 times per day. This usually requires
8 to 12 hours. Check with your dealer for the proper
circulation time for your pool.
2.
3.
Before beginning with any pool care program, you must
first balance your pool water. Take a water sample to your
local pool professional or use a complete test kit that will
test for the following important elements.
If your fill water is high in metals, use a sequestering
agent or metal out product at start-up only before using
the POOL FROG®Mineral Reservoir. See your local dealer
for details on using these products and always follow
manufacturers directions carefully.
4.
5.
Check the pool’s filter gauge often and periodically clean
filter per the manufacturer’s directions. A dirty filter
will slow the flow of water which could hamper proper
circulation.
Water Balance Guidelines
pH: 7.2 – 7.8
Total Alkalinity: 60 – 120 ppm
Calcium Hardness: 150 – 400
Total Dissolved Solids: <1500
Stabilizer: 20 – 80 ppm
Free Chlorine: 0.5 – 1.0 ppm
After your pool is up and running
smoothly, continue to test your
water for pH, total alkalinity and
chlorine with FROG®Brand Test
Strips and maintain its balance
by adding any necessary
adjustment products (see your
dealer for details).
®

5
Start-up and Operation
1.
2.
3.
4.
6.
Add a stabilizer or conditioner to the
pool at the beginning of the season
if the stabilizer level is below 20
ppm. This will prevent chlorine burn
off. Follow manufacturer’s directions
carefully.
Shock the pool with chlorine to rid the
water of all contaminants before begin-
ning with POOL FROG XL PRO®. Follow
manufacturer’s directions carefully.
THIS STEP IS VERY IMPORTANT TO
START-UP.
USE CHLORINE SHOCK ONLY.
Skimmer POOL FROG®
Mineral Cycler
POOL FROG®
Chlorine Cycler
Do not add shock in or near the skimmer or into the POOL FROG XL
PRO® Cyclers as it could damage equipment, risk potential explosion
or discolor your pool surface.
Install a POOL FROG®
Mineral Reservoir into
the POOL FROG®Mineral
Cycler. (Follow directions
on page 7.)
REPLACE THE POOL
FROG® MINERAL
RESERVOIR EVERY
6 MONTHS OR AFTER
ONE POOL SEASON
WHICHEVER IS SHORTER.
POOL FROG®
Mineral Cycler
POOL FROG®
Chlorine Cycler
POOL FROG®
Mineral
Reservoir
POOL FROG®
Mineral Cycler
POOL FROG®
Chlorine Cycler
POOL FROG®
Mineral Cycler
POOL FROG®
Chlorine Cycler
FROG
BAM®
When chlorine reading
is down to 1.0 ppm
(which may take a few
days) insert a POOL
FROG®Pac into
the POOL FROG®
Chlorine Cycler.
(Follow directions on
page 9.)
For an Algae Protection
Guarantee insert FROG
BAM®into POOL FROG®
Mineral Reservoir in
POOL FROG®Mineral
Cycler. (Follow directions
on page 8.)
WARNING
Replace cap and run
POOL FROG®Mineral
Cycler, with POOL FROG®
Mineral Reservoir
inserted, for 10 minutes
on Setting MAXIMUM.
5.
PAC 540C
POOL FROG®
Mineral Cycler
POOL FROG®Pac

6
For the first week test the pool water
daily for free chlorine with FROG®
Brand Test Strips to ensure correct
dial setting. Continue to test weekly
throughout the season.
Start-up and Operation
Start-up and Operation
This system is designed to work effectively with a variety of pool equipment as long as the following basic
procedures are followed.
Once you’ve set the dial on the POOL FROG®Mineral Cycler to Maximum, set control dial on POOL FROG®Chlorine Cycler
by matching up the parameters of your pool on the chart below. THIS IS A STARTING POINT ONLY and may need to be
adjusted to fit your individual pool needs. See #8 below for adjusting directions. IMPORTANT: Pump run times of at least 6
hours per day at high speed are recommended for proper performance. If running the pump at low speed only or on high speed
less than 6 hours, please follow the 24 hour low speed directions below.
7.
24 HOUR, LOW SPEED PUMP RUN TIME
In order to ensure proper performance when running the pump on low speed for
24 hours per day or high speed less than 6 hours per day, bleed the air while
the pump is on by unscrewing BOTH cycler cap knobs until water appears. Then
screw the knobs back on. Repeat this process each time the caps are removed
for any reason. Set the control dial on the chlorine cycler to 6 and follow the
adjustment directions in Step 8 to determine the correct setting for your pool.
8.
After each testing, adjust the dial
up by 1/2 increment if the free
chlorine reading has dropped
below 0.5 ppm or adjust down by
1/2 increment if the reading has
risen above 1.0 ppm. Continue
this process each day until the
free chlorine reading stabilizes to at least 0.5 ppm.
Remember to adjust dial by 1/2 increments only in
order to prevent over chlorination which may bleach pool
surfaces.
Shock pool every two weeks or as needed to
maintain water quality. Follow label directions on
the shock treatment used.
6.
Leave POOL FROG®Chlorine Cycler
empty and set dial on POOL FROG®
Mineral Cycler to Maximum.
7. Shock pool every two weeks or as needed to
maintain water quality. Follow label directions
on the shock treatment used.
If using another means of chlorine support, follow
steps 1-5 on page 5 then continue below.
Find your starting dial setting by matching up the
parameters of your pool on the above chart. An In ground
pool with approximately 18,000 gallons with a 1 horse
power pump running 6 hours a day at high speed would
require a starting dial setting of 4.5. Example above.
9.
Do not add shock in or near the skimmer or into the
POOL FROG XL PRO® Cyclers as it could damage
equipment, risk potential explosion or discolor your
pool surface.
WARNING
Do not add shock in or near the skimmer or into the
POOL FROG XL PRO® Cyclers as it could damage
equipment, risk potential explosion or discolor your
pool surface.
WARNING
SINGLE-SPEED PUMP OR HIGH-SPEED PUMP RUN TIME
In Ground
POOL SIZE
Gallons
6 HOUR PUMP RUN TIME
12 HOUR PUMP RUN TIME
24 HOUR PUMP RUN TIME
PUMP SIZE
3/4 hp 1 hp 1 1/2 hp 2 hp
PUMP SIZE
3/4 hp 1 hp 1 1/2 hp 2 hp
PUMP SIZE
3/4 hp 1 hp 1 1/2 hp 2 hp
7,000 3.5 3.0 2.5 2.5* 2.5 2.0 3.5* 3.0* 1.0 3.0* 2.5* 2.0*
9,000 4.0 3.5 3.0 2.5 3.0 2.5 2.0 3.5* 2.0 3.5* 3.0* 2.5*
12,000 4.5 4.0 3.5 3.0 3.5 3.0 2.5 2.0 2.5 2.0 1.0 3.0*
18,000 NR 4.5 4.0 3.5 4.5 3.5 3.0 2.5 3.0 2.5 2.0 1.5
25,000 NR NR 4.5 3.5 NR 4.5 3.5 3.0 3.5 3.0 2.5 2.0
30,000 NR NR 5.5 4.5 NR 5.0 4.5 3.5 4.0 3.5 3.0 2.5
35,000 NR NR 6.5 5.5 NR 6.0 5.0 4.5 5.0 4.0 3.5 3.0
40,000 NR NR NR 6.5 NR NR 6.0 5.0 6.0 5.0 4.0 3.5
In Ground
POOL SIZE
Gallons
6 HOUR PUMP RUN TIME
PUMP SIZE
3/4 hp 1 hp 1 1/2 hp 2 hp
7,000 3.5 3.0 2.5 2.5*
9,000 4.0 3.5 3.0 2.5
12,000 4.5 4.0 3.5 3.0
18,000 NR 4.5 4.0 3.5
25,000 NR NR 4.5 3.5
30,000 NR NR 5.5 4.5
35,000 NR NR 6.5 5.5
40,000 NR NR NR 6.5
* – Bypass installation recommended. NR – This pump size is not recommended for this size pool.

7
Replacing a POOL FROG®Mineral Reservoir
(POOL FROG® Mineral Reservoirs MUST be Replaced Every Season)
1.
Check the top of the box and back label of product to make
sure you have the correct POOL FROG®Mineral Reservoir to fit
your POOL FROG®Mineral Cycler.
THE POOL FROG®MINERAL RESERVOIR MUST BE
REPLACED EVERY 6 MONTHS OR AFTER ONE POOL
SEASON WHICHEVER IS SHORTER.
IMPORTANT: Remove and read the
information card.
Please note: Complete instructions
for inserting a POOL FROG®Mineral
Reservoir, FROG BAM®and POOL FROG®
Pac are included inside the POOL FROG®
Mineral Reservoir box.
WARNING
USE ONLY the factory recommended replacement
POOL FROG®Mineral Reservoir, FROG BAM®and
POOL FROG®Pac. DO NOT USE any other pac or bulk
chemical tablets in the POOL FROG®Cyclers. Use
of any other product could result in damage to pool
equipment or surface, unsafe pool conditions, fire or
explosion. Warranty will be void if the correct POOL
FROG®Mineral Reservoir, FROG BAM®and POOL
FROG®Pac are not used.
2.
3.
Turn off pump. Turn dial to
Setting 0. This reduces the
flow of water into the unit
when the cap is open.
4.
Use the cap tool included
with POOL FROG XL PRO ®
to loosen cap on POOL
FROG®Mineral Cycler by
hitting the handle with the
flat of your hand counter
clockwise.
5.
Find slot on side
of POOL FROG®
Mineral Reservoir
and line up with fin
inside the POOL
FROG®Mineral
Cycler. Lower POOL
FROG® Mineral
Reservoir into POOL
FROG®Mineral Cycler
until secure.
6.
INGROUND SERIES 5400 (Order #01-12-5462)
NOW FITS THE FOLLOWING CYCLERS:
POOL FROG Series 5400, 5450 or 5600
Prevail Series 5790
®
SINGLE-SPEED PUMP OR HIGH-SPEED PUMP RUN TIME
In Ground
POOL SIZE
Gallons
6 HOUR PUMP RUN TIME
12 HOUR PUMP RUN TIME
24 HOUR PUMP RUN TIME
PUMP SIZE
3/4 hp 1 hp 1 1/2 hp 2 hp
PUMP SIZE
3/4 hp 1 hp 1 1/2 hp 2 hp
PUMP SIZE
3/4 hp 1 hp 1 1/2 hp 2 hp
7,000 3.5 3.0 2.5 2.5* 2.5 2.0 3.5* 3.0* 1.0 3.0* 2.5* 2.0*
9,000 4.0 3.5 3.0 2.5 3.0 2.5 2.0 3.5* 2.0 3.5* 3.0* 2.5*
12,000 4.5 4.0 3.5 3.0 3.5 3.0 2.5 2.0 2.5 2.0 1.0 3.0*
18,000 NR 4.5 4.0 3.5 4.5 3.5 3.0 2.5 3.0 2.5 2.0 1.5
25,000 NR NR 4.5 3.5 NR 4.5 3.5 3.0 3.5 3.0 2.5 2.0
30,000 NR NR 5.5 4.5 NR 5.0 4.5 3.5 4.0 3.5 3.0 2.5
35,000 NR NR 6.5 5.5 NR 6.0 5.0 4.5 5.0 4.0 3.5 3.0
40,000 NR NR NR 6.5 NR NR 6.0 5.0 6.0 5.0 4.0 3.5

8
7.
8.
9.
Using FROG BAM® for an Algae Protection Guarantee
If you are not using FROG BAM, proceed to Step 15.
See FROG BAM® product labeling for complete directions
for use (EPA Reg. No. 53735-9).
For a preventive dose add:
• One FROG BAM® for pools up to 15,000 gallons.
• Two FROG BAM® for pools between 15,000 and 30,000 gallons.
*NOTE: Wait 24 hours after shocking before using FROG BAM. Avoid adding other chemicals until this product has been
circulated (filtered) for at least 24 hours.
Remove cap from
FROG BAM®without
removing seal.
seal
Insert upside down into
center of POOL FROG®
Mineral Reservoir
pushing down firmly on
key to puncture seal.
Replace cap by hand only.
DO NOT OVER TIGHTEN.
Turn control dial on POOL
FROG®Mineral Cycler to
Setting MAXIMUM.
Turn pump on for
90 minutes allowing
FROG BAM®to circulate
through pool.
To remove FROG BAM®,
turn pump off. Turn dial to
Setting 0.
Remove POOL FROG®
Mineral Cycler cap.
NOTE: If water shows
more than a hint of blue
inside POOL FROG®
Mineral Cycler, replace the
cap, turn dial to
Maximum and run the
pump for one minute
14a. If pool size requires
additional FROG BAM®,
repeat steps 7-14.
14b. When water is clear
in POOL FROG® Mineral
Cycler, proceed to step
15.
Lift FROG BAM®up and allow any water in the
container to drain through the POOL FROG®
Mineral Cycler before discarding in trash.
11.
12.
13.
10.
14.
POOL FROG®
Mineral Cycler
POOL FROG®
Chlorine Cycler
FROG
BAM®
POOL FROG®
Mineral Cycler
POOL FROG®
Chlorine Cycler
FROG
BAM®

9
Turn POOL FROG®
Pac over and
shake slightly until chlorine
tablets fall into tower areas.
POOL FROG®Pac recommended to
assure up to 50% reduction in chlorine
use*. POOL FROG®Pac sold separately.
(EPA Reg. No. 53735-2)
*Compared to the minimum EPA recommended
chlorine level of 1.0 ppm for a stabilized swimming pool.
Using the
POOL FROG®
Pac
WARNING – USE ONLY the factory recommended replacement POOL FROG®Pac. (See
label.) DO NOT USE any other pac or bulk chemical tablets in the POOL FROG®Cycler.
Use of any other product could result in over chlorination, bleached liners, unsafe pool
conditions, fire or explosion. Warranty will be void if the correct pac is not used.
Avoid sparks, open flame or smoking
when handling the POOL FROG®Pac.
Cut handle from POOL FROG®Pac using a PVC
cutting tool or a hacksaw (KEEP OUT OF REACH OF
CHILDREN).
16.
17.
A. Find the
indent in the
plastic.
B. If using a PVC cutting tool,
place curved section of tool
around the narrow end of one
pac tower and line up blade on
indent.
C. Squeeze the handles
together. Repeat for other
side.
D. If using a hacksaw to cut
the pac, line up hacksaw
blade on indent and cut with
a smooth sawing action.
E. Whether using a PVC
cutting tool or a hacksaw,
make sure the blade comes
straight across on the
indent line for a clean cut.
F. If openings are pinched
together, open with fingers or
re-cut closer to the colored
screens inside POOL FROG®
Pac. Leave at least 1/4” of
plastic to fit into POOL FROG®
Chlorine Cycler base.
Finished cut ends
Avoid a
pinched
opening.
A correct oval
opening
Indent in plastic
18.
19.
POOL FROG
Pac
towers
Insert POOL FROG®
Pac into POOL FROG®
Chlorine Cycler, lining up
the openings in the POOL
FROG®Pac with keys in
the POOL FROG®Chlorine
Cycler.
NOTE: Openings are a
different shape than keys.
Opening in
POOL FROG Pac
Key in POOL
FROG Chlorine
Cycler
Avoid sparks, open flame or smoking while handling the
POOL FROG®Pac.
Replace cap by hand only.
DO NOT OVERTIGHTEN.
DO NOT USE CAP TOOL TO TIGHT-
EN CAP. FOR REMOVAL ONLY.
The chlorine pacs are made of HDPE plastic.
Non-refillable container. Do not reuse or refill
this container. Offer for recycling if available.
Rinse thoroughly before recycling or discarding
in trash.
Mark your calendar for the six month
replacement of the POOL FROG®
Mineral Reservoir, 90-day replacement
of FROG BAM®and approximate replacement
times for the POOL FROG®Bac Pac. Once
wetted, the time-released mineral coating of the POOL
FROG®Mineral Reservoir is effective up to 6 consecutive
months or one pool season whichever is shorter. After that
time, even if you hear the spent media inside, it is no longer
effective and must be replaced.
20.
21.
POOL FROG
Pac
towers
®
PAC 540C
POOL FROG®
Mineral Cycler
POOL FROG®
Chlorine Cycler
PAC 540C
POOL FROG®
Mineral Cycler
15.

10
1.
2.
3.
4.
5.
Troubleshooting
For more in-depth troubleshooting, go to www.kingtechnology.com
Problem Remedy
What do I do
if the water looks
cloudy?
1. Make sure your filtration
system is working properly (i.e.
clean filter, skimmer and pump
basket).
2. Make sure circulation time is
adequate – increase pump time
if not.
3. Make sure the pool is
properly balanced (see page 4).
4. Shock the water to eliminate
build up of any organic matter.
5. Make sure pool has a
free chlorine reading of
0.5 to 1.0 ppm.
6. Check with your dealer for
more information.
What do I do
if the water turns
color?
1. Metals in the fill water may
have been oxidized. Have the
pool tested. Shock the pool and
clean the filter until water clarity
returns.
2. Algae may be trying to form
– shock the pool, increase
circulation time if needed and
clean the filter.
3. Check with your dealer for
more information.
What do I do
if algae forms in
or on my pool?
1. Use a nonmetallic (polyquat)
algaecide per the directions on
the bottle and brush the sides
of the pool often.
2. Clean the filter and shock
the pool with chlorine daily until
water clarity returns.
3. If you are in an area of the
country that struggles with
algae growth, see your dealer
regarding a 90-day Algae
Protection Guarantee using
FROG BAM®. See product hang
tag for guarantee details.
4. Check with your dealer for
more information.
What do I do
if I am under
chlorinating with
the POOL FROG®
Pac?
1. If you are unable to maintain
0.5 to 1.0 ppm, first make sure
there are chlorine tablets in the
tower areas of the POOL FROG®
Pac and it is installed properly. If
a correction was made, test the
water in 24 hours.
2. If still low, turn the dial up
one setting and test the water
again in 24 hours. Continue
raising the setting by one
increment each day until the
proper reading is achieved.
3. Shock the pool if the reading
has been lower than 0.5 ppm
for more than one day.
4. Make sure pump run time
is at least 6 hours on high
speed (40 gpm or higher) or if
not, bleed the air from both
cap knobs (see page 6 for
directions).
5. Contact your dealer to have
your back pressure tested to
ensure it is at least 4 psi.
6. Check for a suction side
leak by looking for air bubbles
in your pump basket or at the
return jet. Your water level will
be low and the skimmer will be
taking in air. Contact dealer for
help in correcting this situation.
7. Contact King Technology’s
Customer Service Department
at 800-222-0169.
What do I do
if I am over
chlorinating with
the POOL FROG®
Pac?
1. If the chlorine reading is over
3.0 ppm, remove the Chlorine
Pac from the POOL FROG®
Chlorine Cycler and test the
water daily until the reading is
down to 1.0 ppm.
2. Reinsert the POOL FROG®
Pac, lower the dial one setting
and test the water again in 24
hours. If the reading has risen,
lower the dial one setting again.
Continue this process until
proper reading is achieved.
3. If over-chlorinating at the
lowest possible setting,
consider decreasing the
circulation time. Depending on
your pump size, you may be
circulating the water more than
is necessary.
4. Contact your dealer to have
your back pressure tested. If
over 8 psi consider a larger
eye-ball fitting in the return jet.
5. Check to see if the
pressure relief valve is loose
or missing and replace.
It is a clear plastic piece
approximately 1” long
installed inside near the base.
If loose or missing, it can
provide another avenue for
water to reach the chlorine.
6. Contact King Technology’s
Customer Service Department
at 800-222-0169.

11
For more in-depth troubleshooting, go to www.kingtechnology.com
Parts List
INCLUDED WITH POOL FROG XL PRO®CYCLERS
REF. # DESCRIPTION QTY. INCLUDED
1 & 2 Cap w/O-Ring 1
3 Body 1
4 Pressure Relief Valve 1
5, 6, 7 Control Dial with O-Ring
& Snap Ring 1
8 & 9 Knob with O-Ring 4
10 2” Male Adapter 2
11 Cap/Control Dial Tool 1
12 Silicone Lubricant 1
13 Shroud 1
REPLACEMENT PARTS FOR POOL FROG XL PRO®CYCLERS
REF. # PART NO. DESCRIPTION
1 & 2 01-22-9412 Cap w/O-Ring
2 01-22-9920 Cap O-Ring
4 01-22-9480 Pressure Relief Valve
5, 6, 7 01-22-9440 Control Dial with O-Ring & Snap Ring
6 & 7 01-22-9450 Control Dial O-Ring Kit
8 & 9 01-22-9940 Knob with O-Ring
10 01-22-9490 2” Male Adapter
11 01-22-8870 Cap/Control Dial Tool
12 01-22-9971 Silicone Lubricant

12
S
IL
I
C
O
N
E
L
U
B
R
I
C
A
N
T
1.
2.
3.
4.
5.
1.
2.
3.
POOL FROG®Cycler Maintenance
Replacing the Control Dial O-Rings
Using a needle nose pliers,
find the snap ring tail located
at approximately the five
o’clock position under the
control dial.
Pull down and out of the
groove.
Using a large screwdriver,
loosen the control dial.
Carefully pry the dial until it
pulls out.
Carefully replace the rubber
o-ring without stretching it.
Apply silicone lubricant, that
came with your POOL FROG
XL PRO®, on o-ring.
Push control dial completely
into the housing and turn the
dial to setting 2.
Replacing Cap O-Ring
Lubricate o-ring often with
silicone lubricant that
came with your POOL FROG
XL PRO®. DO NOT USE
petroleum based lubricants.
Replacing Knobs
Replace knob in back or on cap
of both POOL FROG XL PRO®
Cyclers by unscrewing old one
and screwing in new one.
Hold cap in front of you
upside down with the o-ring
groove facing up. Place one
end of o-ring into cap groove
at the point closest to you.
Hold o-ring down with the
thumb and index finger of
one hand.
Take hold of the far end of
the o-ring with the thumb
and index finger of the other
hand. Roll o-ring slightly
back towards you as you
stretch the o-ring into the
remainder of the cap groove.
12
Insert the non-lipped end
of snap ring into the groove
opening beginning at the
5 o’clock position and push
it up so that it threads itself
around the control dial.
6.
7. Using a small screwdriver or
pointed tool to help guide it,
make sure the snap ring stays
in the groove as it is inserted.
C
OP
Y
C
OP
Y
C
O
PY
C
O
P
Y
x
xxx
x
S
L
I
CO N
E
L
U
B
R
I
C
A
N
T
Back of Cycler
Or top of cap

13
Winterizing
1.
3.
2.
Turn pump off and turn dial
to Setting 0.
Remove both caps.
Unscrew knob in the back
of both POOL FROG XL
PRO®Cyclers. Allow all
water to drain.
4.
5.
6.
Do not store near
motorcycles, cars or
anything metal that can
rust, pit, etc.
Make sure POOL FROG®
Pac is away from open
flame.
Remove the POOL FROG®
Mineral Reservoir and
discard in trash. Even if
you hear spent minerals
inside, it is no longer
effective.
Remove the POOL FROG®
Pac. If it still contains
chlorine, wrap in plastic
bag and store in shed
or cool, well-ventilated
location away from children
and pets.
Replace both caps and
knobs loosely.
POOL
FROG®
Pac
PAC 540C

14
PVC
CEMENT
W
a
t
e
r
C
Y
C
L
E
R
M
et
e
r
e
d
P
o
o
l
P
u
r
i
f
i
e
r
In-line Installation
Do NOT install
POOL FROG
XL PRO®off-line.
Following Primer directions, brush Primer on the inside
of the male adapters and to ends of pipe. Repeat this
process with PVC cement following directions on that
product.
Measure the distance between
outside male adapters and cut
out a section of pipe 3” less
than that dimension.
Allow a minimum of 12” above and on each
side of POOL FROG XL PRO®to ensure room
for easy replacement of POOL FROG®Mineral
Reservoir and POOL FROG®Pac.
Insert PVC pipe into male
adapters with a twisting action.
Hold in place 5 to 10 seconds
to bond.
TOOLS NEEDED
Hacksaw
MATERIALS NEEDED
Tape Measure
Primer and PVC Cement
RECOMMENDED
Corrosion Resistant
Check Valve
#10 x 1 1/4” Phillips
Pan Head Screws with
Washers
Use Phillips pan head
screws through the
mounting holes at the
POOL FROG®Cycler
bases to secure the
POOL FROG XL PRO®
into a treated wood
base. Isolating the POOL FROG XL PRO®by installing a
corrosion resistant check valve is recommended.
1.
3. 4.
Pipe Wrench
Bi-flow valve design
allows water flow in
either direction.
PAC 540C
2.
Do NOT install in copper pipe
if using POOL FROG®Pac as
chemical corrosion occurs.
• Install after all equipment and as far
as possible from heater.
• Any additional sanitizing equipment
that is installed with FROG®must be
installed after FROG®(never before)
on the return line to the pool.
WARNING

15
For Proper Performance
1) If using a multi-speed pump, run pump for at
least 6 hours per day at high speed (at least 40
gpm).
If the pump will run on low speed
24 hours per day or less than 6
hours per day on high speed, you
must bleed the air while the pump
is on by unscrewing the cap knob
until water appears. Then screw the
knob back on. Repeat this process
each time the cap is removed for
any reason.
2) Install system with a minimum 4 psi back
pressure.
Lower back pressures could result in under
chlorination. Adjust eye ball fittings
in the return jets to a smaller size
to increase back pressure. Contact
King Technology at 800-222-0169
for a cap tapped for a pressure
gauge to determine back pressure
at pool start-up.
3) Special installation:
•If water flow is higher than 80 gpm, see
diagram A.
•If an in-floor cleaner is included with pool,
see diagram B, with two options. Preferred
installation is Option 1 with two separate lines.
•If set-up is a pool and spa combination with
common equipment, see diagram C.
•Any additional sanitizing equipment that is
installed with FROG®must be installed after
FROG®(never before) on the return line
to the pool.
NOTE: Over chlorination or damage to the POOL
FROG®Cycler or other equipment could result if
these special installations are not used in these
situations.
A. With High GPMS
Install T-fittings exactly as shown.
C. Pool and Spillover Spa Combination
B. With In-Floor Cleaner - TWO OPTIONS
✙
✙
✙
✙
✙
Flow
Flow
The best option is to have two lines. One line with pump, filter, heater
and cycler and a second line with a separate pump for the in-floor clean-
ing system (filter optional).
OPTION 1- A Two-Line Installation
OPTION 2 - A 3-Way Valve Installation
POOL WATER LEVEL
POOL WATER LEVEL
POOL WATER LEVEL
POOL RETURN
3-way manual valve or 3-way motor valve plus controls
POOL FROG
XL PRO
POOL FROG
XL PRO
IN-FLOOR
CLEANER
VALVE
IN-FLOOR
CLEANER
VALVE
FILTER
FILTER
FILTER HEATER
PUMP
PUMP
PUMP
Line 1
Line 2

16
POOL FROG XL PRO®Two-Year Limited Warranty
King Technology, Inc. warrants to the original purchaser this
unit will be free from any defects in workmanship and/or
material, for a period of two (2) years from the date of original
purchase. This warranty covers body, cap and control dial, but
specifically excludes o-rings. King Technology at its option may
replace any defective parts or the entire unit without charge
after it is determined what is needed to correct any deficiency.
Replacement parts with the exception of o-rings are warranted
for the remainder of the original warranty. To extend the limited
warranty from two years to ten years, simply complete the
warranty card that came with your unit and return it to King
Technology within 30 days of purchase and installation.
1. To obtain warranty service, you must deliver the unit to King
Technology or its nearest authorized dealer. Shipping expenses
are the purchaser’s responsibility. The name of the nearest
authorized dealer can be obtained by writing or calling King
Technology at the address and telephone number provided
below. Proof of purchase is required when requesting warranty
service. Purchaser must present the sales receipt or other
documentation verifying proof of purchase.
2. This warranty does not cover defects caused by:
Modification, alteration, repair or service of the unit contrary
to the accompanying instructions; physical abuse to or misuse
of the product or operation or installation in a manner contrary
to the accompanying instructions. This warranty also excludes
all costs arising from the installation, adjustment, removal or
replacement of defective units or parts. This warranty also
excludes any and all claims arising out of the chemicals used
in the product or their characteristics.
3. CAUTION - Read carefully – Failure to follow these
instructions will void the warranty. Do not add shock in or
near skimmer.
A. This unit is not designed for shock treatment of pools.
See your pool dealer or distributor for further information
concerning shock treatments.
B. Control dial settings higher than needed can result in
excess sanitizers being discharged into the pool. If the
sanitizer level goes unmonitored, it can result in bleaching or
discoloration of areas around the pool inlet or in some cases
bleaching or discoloration of the entire pool liner or paint.
C. Excess trichlor in the pool can create health hazards to
bathers. Consult each chemical manufacturer’s warnings and
cautions for specifics.
D. Misuse or failure to use the proper POOL FROG®Mineral
Reservoir and POOL FROG®Pac may cause damage to
equipment or personal injury. This warranty will be null and
void, if this unit is not used with the recommended POOL
FROG®Mineral Reservoir and POOL FROG®Pac.
4. This warranty is the exclusive warranty for the POOL FROG
XL PRO®. This warranty is not transferable. KING
TECHNOLOGY MAKES NO REPRESENTATION OR
WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, AS TO
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE
OR ANY OTHER MATTER CONCERNING THE POOL FROG
XL PRO®. Any express warranty not provided herein, and any
remedy for breach of contract but which for this provision might
arise by implication or operation of law is hereby excluded and
disclaimed. THE EXCLUSIVE REMEDY FOR ANY CUSTOMER
IS THE REPAIR OR REPLACEMENT OF THE UNIT, AND THE
RECOVERY OF DAMAGES WILL NOT EXCEED THE PURCHASE
PRICE OF THE UNIT. IN NO EVENT WILL KING TECHNOLOGY BE
LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, SPECIAL OR
PUNITIVE DAMAGES FROM ANY CAUSE.
5. Under no circumstance shall King Technology be liable to
purchaser or any other person for any damage or loss incurred
because of any chemicals used in the product or their physical
characteristics, or interruption of service of the product, or
any resulting special, incidental or consequential damages or
losses. Some states do not allow the exclusion or limitation of
incidental consequential damages, so the above limitation or
exclusion may not apply to you.
Made in U.S.A.
U.S. Patents D571,432; 6,190,547; 6,210,566; 6,217,892; 6,383,507;
6,544,415; 6,551,609; 6,652,871 and other U.S. and Foreign patents
pending.
20-48-0220E 553091143R6N
Manufactured by: KING TECHNOLOGY, INC.
530 11th Avenue South, Hopkins, MN 55343 U.S.A.
952-933-6118 • 800-222-0169 • FAX [phone]
www.kingtechnology.com
FROG®, POOL FROG®, XL PRO®, SPA FROG®, INSTANT FROG®, FILTER FROG®, BAM®,
NEW WATER® and SANI-KING® are registered trademarks of King Technology, Inc.