FSL Scoreboards M02-CLK4 User manual

M02-CLK4

M02-CLK4 Page 2 of 12
1) Scoreboard connections:
The scoreboard should be supplied with a 230V mains supply.
The mains supply should be fed through a 5 amp circuit breaker
and it is highly recommended that the supply should be fed through
a Residual Current Device (RCD)
If the scoreboard has been supplied with a separate aerial this
should be mounted as high as possible
2) On Power Up:
'Cd - ' will be displayed for 5 seconds
oThis is a "code" number stored in memory
oThere are 5 possible codes that may be used, this
allows a number of displays to be operated in close
proximity of each other
oFurther details on programming the code can be
found at the end of the manual
The scoreboard will now go into normal operation, displaying
scores with the clock blanked.

M02-CLK4 Page 3 of 12
3) Changing Scores:
1. To increase the score press the
button
2. To decrease the score press the button

M02-CLK4 Page 4 of 12
3. To clear the score press the &
button together

M02-CLK4 Page 5 of 12
4) Brightness Setting:
To access brightness setting, hold buttons & on the
handset together for 3 seconds until 'bl - ' is displayed
To exit brightness setting, hold buttons & on the
handset together for 3 seconds until the scores are displayed again

M02-CLK4 Page 6 of 12
Increasing Brightness:
While 'bl - ' is displayed, increase brightness with button
The maximum brightness is 9
Decreasing Brightness:
While 'bl - ' is displayed, decrease brightness with button
The minimum brightness is 0
To exit brightness setting, hold buttons & on the
handset together for 3 seconds until the scores are displayed again

M02-CLK4 Page 7 of 12
6) Scoreboard Blank:

M02-CLK4 Page 8 of 12
7) Time Mode Menu:
To access 'Time Mode Menu', hold button for 3 seconds
until 'tu'is displayed
Pressing button will scroll through the 3 time menu options,
displayed as :
o'tu' –Timer up in minutes and seconds
o'td' –Timer down in minutes and seconds
o'bn' –Blank/clear the clock
While displaying one of the time options above, holding button
for 3 seconds will go into that corresponding option

M02-CLK4 Page 9 of 12
NOTE: 'Time Mode Menu' cannot be accessed when brightness is
being set
7.1) While in 'tu' (Timer Up in minutes):
NOTE: Defaults to 0 minutes, no setting of timer up is required
When “Se” then “St” appears on the screen, this indicates to set
the start minutes
Press button to INCREASE the minutes
Press button to DECREASE the minutes
Hold down the button for 3 seconds, until “Se” then “SP”
appears on the screen, using the same increase and decrease
button, set the Stop time.
To store and display the 'Timer Up', hold button for 3
seconds
oPress button to START/STOP the timer

M02-CLK4 Page 10 of 12
oONLY if timer is STOPPED press button
to RESET the timer to what it was previously set
While displaying the 'Timer Up', hold button for 3
seconds to go into the 'Time Mode Menu' again
7.2) While in 'td' (Timer Down in minutes):
The timer setting that can be changed will flash
Press button to switch through minutes and seconds setting
Press button to INCREASE the
minutes/seconds
Press button to DECREASE
the minutes/seconds

M02-CLK4 Page 11 of 12
To store and display the 'Timer Down', hold button for 3
seconds
oPress button to START/STOP the timer
oONLY if timer is STOPPED press button
to PRESET the timer to what it was previously set
While displaying the 'Timer Down', hold button for 3
seconds to go into the 'Time Mode Menu' again
7.3) While in 'bln' (Blank Clock):
NOTE: Defaults to clearing the clock
While displaying the 'Blank Clock', hold button for 3 seconds
to go into the 'Time Mode Menu' again

M02-CLK4 Page 12 of 12
FSL ELECTRONICS LTD
SANDHOLES ROAD
COOKSTOWN
CO TYRONE
N. IRELAND
BT80 9AR
[phone]
www.fslelectronics