FUHR NBFP490 Manual

WWW.FUHR.DE
www.fuhr.de
834
autotronic
Content
1 Application ................................................................................................................................................2
2 Delivery scope............................................................................................................................................2
3 Positioning.................................................................................................................................................2
4 Installation requirements ............................................................................................................................3
5 Installation dimensions...............................................................................................................................3
6 Installation and component description ......................................................................................................4
7 Master radio key ........................................................................................................................................5
8 User keys ...................................................................................................................................................5
8.1 Tuning in new user keys in to the radio receiver ...............................................................................5
8.2 Deleting specific individual user keys from the memory...................................................................6
8.3 Deleting all user keys completely from the radio receiver’s memory..................................................6
9 Technical data ............................................................................................................................................7
9.1 Radio receiver.................................................................................................................................7
9.2 Master radio key.............................................................................................................................7
10 The radio receiver’s LED signals...................................................................................................................7
11 Safety instructions, maintenance and care ..................................................................................................8
11.1 Changing the radio key battery .......................................................................................................8
Radio receiver module NBFP490 with master radio key
Installation, operation and maintenance instructions
These instructions are to be passed
on by the fitter to the user.
MBW24-GB/06.19-11

WWW.FUHR.DE
2
834
autotronic
Radio receiver
Drive unit
Drive unit’s
coupler
1 Application
The radio receiver module NBFP490 is a rolling-code radio receiver for opening FUHR multitronic 881 and
autotronic 834(P) motorised lock systems, by means of up to max. 25 different radio transmitters.
The radio receiver is compatible with all conventional FUHR transmitter modules, e.g.: radio key, radio transponder
reader, radio fingerprint scanner, radio keypad.
2 Delivery scope
Radio receiver with connection cable Master radio key, 3 channels
Radio key
NZ80062 NZ80182F
Transponder
NB693N
Fingerprint
scanner
NB649N
Keypad
NB702N
3 Positioning
The radio receiver is inserted behind the lock faceplate
at the top end of the multitronic 881-/ autotronic
834-drive unit and connected with the enclosed
3-core connection cable to the drive unit’s green
coupler.

WWW.FUHR.DE 3
834
autotronic
1
2
E92
280
132
226
57
193
4 Installation requirements
The following FUHR motorised locks’ components
have been modified from the manufacturing date April
2010, in order to facilitate the installation of the radio
receiver:
1 Opening for the LED tune-in button in the lock face-
plate
2 Insertion device on the drive unit
Motorised locks that are not equipped with both of
these modifications are unsuitable for installing these
radio receivers. For this purpose please use a control
unit on the frame with integrated radio receiver.
5 Installation dimensions
Tip: On metal door leaves, the reception range can be increased by notching out the profile
wall towards the glazing rebate area behind the radio receiver modul.
The module fits into the 280 mm long drive unit’s standard routing.

WWW.FUHR.DE
4
834
autotronic
2
4
7
1
6
5
6
3
1234567
6 Installation and component description
The radio receiver module NBFP490 (1) has a trans-
parent tune-in button with a red indicator LED (2) to
tune in the FUHR radio transmitter, as well as a 3-core
connection cable (3) to be connected to the drive unit
with the green coupler.
To position and fix the drive unit, the radio-controlled
module’s housing is equipped with an insertion
channel (4) and a catch spring (5). The drive unit is
equipped with appropriate mounting areas* (6). Slide
the radio receiver module downwards along the inser-
tion channel until the catch spring in the motor drive’s
housing positively engages into place.
There is an opening* (7) in the lock faceplate located
above of the drive unit, through which one can activate
the LED tune-in button (2) in a built-in state from the
outside with a thin object.
This LED tune-in button must be pressed first for
disassembly, before the radio receiver module can be
removed towards the top.
*From date of manufacture: 04/2010
Three cables are located on the back of the radio receiver: white, brown & green. Please connect these three cables
in the correct order to the following screw terminals on the drive unit’s coupler:
Terminal 4 – white cable
Terminal 5 – brown cable
Terminal 6 – green cable
After the motorised lock’s 12 V DC power supply has
been connected (terminal 2-3 refer to installation
instructions multitronic 881/ autotronic 834 –
www.fuhr.de), the radio receiver is operational.

WWW.FUHR.DE 5
834
autotronic
7 Master radio key
The radio receiver distinguishes between master keys and user keys.
The master key is always unique! It cannot be deleted, replaced or modified. More user keys can be
tuned in to the radio receiver with it, or alternatively user keys can also be deleted. The master key is
a one-off and under no circumstances may it be lost! It is also suitable for opening the door.
Your radio receiver is supplied with a factory tuned in master key. You recognise the master key by the three red
control keys.
The tuned in master button is located in the centre.
Both of the other buttons are unallocated transmission
buttons (e.g. for garage door drive units etc.).
You can immediately emit a radio signal to open the
door with the master key. The LED tune-in button lights
up for 2 seconds, if the applicable signal is detected.
LED tune-in button
Master button
8 User keys
Apart from the previously tuned in master key, up to 25 user keys can be tuned in to the radio receiver. The user
keys serve only to open the door; they have no tuning in or deleting authorisation.
All FUHR radio transmitters are suitable as user transmitters, e.g.: radio key, radio fingerprint scanner, radio trans-
ponder, radio keypad.
8.1 Tuning in new user keys in to the radio receiver
1. Activate the radio receiver’s LED tune-in button briefly (<1 second).
ØThe LED tune-in button flashes slowly.
2. Press the master key’s centre, red transmitter button once within 20 seconds.
ØAs soon as the radio receiver accepts the master, the radio receiver’s LED tune-in button lights up for approx.
2 seconds and then continues to flash slowly.
3. Press the new user key’s transmitter button twice consecutively within 20 seconds!
ØAs soon as the radio receiver detects and saves the new user key, the LED tune-in button on the radio receiver
lights up for 4 seconds and then goes out automatically.
ØThe user key can now be used to open the door.
The tuning in procedure is aborted if the 20 second time limit is exceeded or if an incorrect master key
is used.

WWW.FUHR.DE
6
834
autotronic
8.2 Deleting specific individual user keys from the memory
If you would like to remove the opening authorisation from a previously tuned in user key, you can delete this
specifically from the radio receiver’s memory. To do so, please proceed as follows:
1. Press the radio receiver’s LED tune-in button for longer than 3 seconds.
ØThe LED begins to flash fast
ØRelease the button.
2. Press the master key’s transmission button once within 20 seconds.
ØAs soon as the radio receiver accepts the master, the radio receiver’s LED tune-in button lights up for approx.
2 seconds and then continues to flash quickly.
3. Press the user key to be deleted once within 20 seconds.
ØIf the LED tune-in button lights up for approx. 4 seconds, the respective transmission code is deleted.
4. Check using the user key, as to whether the delete process was successful!
8.3 Deleting all user keys completely from the radio receiver’s memory
If you would like to remove the opening authorisation from all previously tuned in user keys, you can delete the
radio receiver’s memory completely. Only the master key remains active. To do so, please proceed as follows:
1. Press the radio receiver’s LED tune-in button for longer than 3 seconds.
ØThe LED begins to flash fast
ØRelease the button.
2. Press the master key’s transmission button once within 20 seconds.
ØAs soon as the radio receiver accepts the master, the radio receiver’s LED tune-in button lights up for approx.
2 seconds and then continues to flash quickly.
3. Press the radio receiver’s LED tune-in button again for longer than 3 seconds.
ØIf the LED tune-in button lights up for approx. 4 seconds, all transmission codes – with the exception of the
master – are deleted.
In order to rule out the possibility of anyone else except the authorised end customer tuning
in a user key, we recommend end customers to carry out this deletion process immediately
after receiving the master key!

WWW.FUHR.DE 7
834
autotronic
9.1 Radio receiver
Frequency: 868.3 MHz
Modulation: FSK (frequency shift keying)
Security: Rolling-code with master
transmission principle
Aerial: On board
Power supply: 12 V DC
Current consumption: 15 mA
Operating control: Red light emitting diode (LED)
Temperature range: -10°C to +50°C
Dimensions: 43 x 40 x 15 mm
Connection cable: 3-core, approx. 320 mm long
Weight: approx. 50 g
IP rating: IP 20
Switching impulse: Potential-free
9.2 Master radio key
The hand-held transmitters conform to the R&TTE
guideline 2014 /53/EU
Frequency: 868.3 MHz
Modulation: FSK (frequency shift keying)
Security: Rolling-code
Channels: 3
Power supply: 1 x 3 V battery, CR 2032
Operating control: Red light emitting diode (LED)
Temperature range: -10°C to +50°C
Dimensions: 53 x 36 x 15 mm
Weight: approx. 20 g
9 Technical data
10 The radio receiver’s LED signals
The following LED signals can only be checked after applying the 12 V DC power supply.
The LED tune in button lights up permanently ØA master key has not been tuned in yet.
Please note: The first radio transmitter tuned in is
the future master radio transmitter!
The LED tune in button lights up for 2 seconds ØA previously tuned in transmission signal has been
picked up, the lock unlocks motor-driven.
The LED tune in button lights up for 0.5 seconds ØA transmission signal that has not been tuned in yet
has been picked up, the lock does not unlock.
The LED tune in button doesn’t light up at all ØThe LED does not light up in the non-actuated
original position, as no transmission signal has been
picked up. Should the LED not light up despite trans-
mitting an opening signal, the radio receiver and/or
the motor lock have not yet been connected to the
12 V DC operating voltage or the cables on the drive
unit’s coupler have been connected incorrectly.

834
autotronic
11 Safety instructions, maintenance and care
The radio receiver module is maintenance-free. If the radio key’s transmitter range deteriorates, please replace the
battery (refer to chapter 11.1).
The supplied components are to be protected against humidity. They are not suitable for areas with high humidity
and chemical substances!
Only original FUHR accessories may be used. We accept no liability for incorrect installation or operation. The
housings and cables are to be protected against mechanical damage. Damaged or faulty components must be
decommissioned and replaced immediately.
11.1 Changing the radio key battery
1. Open the housing with a coin. 2. Slide out the battery downwards.
3. Insert the new CR2032 battery,
with the + pole pointing upwards.
4. Press the casing together again.
CARL FUHR GmbH & Co. KG
Carl-Fuhr-Straße 12 D-42579 Heiligenhaus
Tel.: [phone] Fax: [phone]
www.fuhr.de · [e-mail]