Fujioh FH-GS6020 SVSS Manual

FH-GS6020 SVSS
FH-GS6030 SVSS
FH-GS6020 SVGL
FH-GS6030 SVGL

Preface
Thank you for choosing our gas hob.
To use this appliance correctly and prevent any potential risk, read these instructions
before using the appliance.
Keep these instructions in a place where you can find them easily.
If you are unsure of any of the information contained in these instructions, please contact
our customer care centre.
The manufacturer shall not be responsible for any damages to persons or property caused
by incorrect installation or use of the appliance.
The appliance has been certified for use in countries other than those marked on the
appliance.
The manufacturer also reserves the right to make any modifications to the products as may
be considered necessary or useful, also in the interests of the user, without jeopardising
the main functional and safety features of the products themselves.
The appliance is designed for a domestic environment and not a commercial one.
1

2
Contents
Preface
Description of the appliance
How to use the appliance
4
Using instructions
Installing the appliance
Inlet gas connection
Gas specification
Installing the battery
Trouble shooting
Safety Warning
Installation
During use
Environmental information
Pot placement tips
Instructions for use and maintenance
Technical instructions
6
7
8
9
22

Safety Instructions
Danger/Warning
Caution Neglect of this mark may result in minor personal injury
or property damage.
Caution No Access
No Fire Tool Must Do
Danger
- Do not turn on the light.
- Do not switch on/off any electrical appliance and do not touch any electric plug.
- Do not use a telephone.
1 Stop using the product and close the main valve.
2 Open the window to ventilate.
3 Contact our service centre by using a phone outside.
cilrag nettor fo llems( kael sag eht llems nac uoy taht os ,natpacrem sniatnoc sag leuf ehT *
or egg) even where only 1/1000 of the gas is in the air.
The following marks are used in the Instruction Manual
as follows:
3
If gas seems to leak,take the actions as follow:
Neglect of this mark may result in severe personal injury
or death.
Please take the time to read this Instruction Manual before installing or using the appliance.
This instruction booklet must be kept with the appliance for any future reference.
If the appliance is sold or transferred to another person,ensure the booklet is passed on to
the new user.
The manufacturer declines any liability should these safety measures not be observed.
The following marks are made to be easily understood so that you can prevent any
accident caused by misuse in advance, and use the appliance more conveniently.
Read the following contents thoroughly and ensure you understand them.

Installation
Warning
This appliance shall be installed in
accordance with regulations in force
and only used in a well ventilated
space.
Prior to installation,ensure that the
gas and ignition supply complies with
the type stated on the rating plate.
The gas pipe must be installed in
such a way that they do not touch
any parts or the appliance.
Caution
4
DC1.5V
■ This appliance should be installed by a qualified technician or installer.
■ The adjustment conditions for this appliance are stated on the label or data plate.
■ Remove all packaging before using the appliance.
■After unpacking the appliance, make sure the product is not damaged.Otherwise,
contact the dealer before installing the appliance.
■ The adjacent furniture and all materials used in the installation must be able to
withstand a minimum temperature of 85˚C above the ambient temperature of the
room it is located in, whilst in use.
■ In the event of burner flames being accidentally extinguished, turn off the burner
control and do not attempt to re-ignite the burner for at least one minute.
■
The use of a gas cooking appliance results in the production of heat and moisture in the
room in which it is installed. Ensure that the kitchen is well ventilated: keep natural
ventilation holes open or install a mechanical ventilation device (mechanical extractor hood).
■ Prolonged intensive use of the appliance may call for additional ventilation, for
example opening of a window, or more effective ventilation, for example increasing
the level of mechanical ventilation where present.

Child and People Safety
Do not allow children to play near or with the appliance.
The appliance gets hot when it is in use.
Children should be kept away until it has cooled.
Warning
Caution
5
■ This appliance is designed to be operated by adults.
■ Children can also injure themselves by pulling pans or pots off the appliance.
■ This appliance is not intended for use by children or other persons whose physical,
sensory or mental capabilities or lack of experience and knowledge prevents them
from using the appliance safety without supervision or instruction by a responsible
person to ensure that they can use the appliance safety.

During use
Warning
The use of a gas cooking appliance
results in the production of heat and
moisture in the room in which it is
installed. Ensure that the kitchen is
well ventilated : keep natural
ventilation holes open or install a
mechanical ventilation device
(mechanical
extractor hood).
Never leave the appliance unattended
when cooking.
Burner
panel is not designed to operate from
an external timer or separate remote
control system.
6
■ Only use the appliance for preparing
food.
in contact with water. Do not operate
this appliance with wet hands.
■ Do not use this appliance if it comes
■ The heating and cooking surfaces of
the appliance become hot when they
are in use, take all due precautions.
■ Do not use large cloths, tea towels or
similar as the ends could touch the
flames and catch fire.
■ Unstable or misshapen pans should
not be used on the appliance as they
can cause an accident by tipping or
spillage.

During use
■ Do not spray aerosols in the vicinity of
this appliance while it is in operaiton. ‘ ’ position when not in use.
Caution
7
■ Do not use or store flammable materials
in the storage drawer near this
appliance.
■ Perishable food, plastic items and
aerosols may be affected by heat and
should not stored above or below the
appliance.
■ Ensure the control knobs are in the
This appliance is intended for domestic cooking only.It is not designed for commercial
or industrial purposes.
Prolonged intensive use of the appliance may call for additional ventilation,for example
opening of a window, or increasing the level of mechanical ventilation where present.
■ Use heat-resistant pot holders or gloves when handling hot pots and pans.
■ Do not let pot holders come near open flames when lifting cookware.
■ Take care not to let pot holders or gloves get damp or wet, as this causes heat to transfer
through the material quicker with the risk of burning yourself.
■
If you have any mechanical parts eg. an artifical heart in your body, consult a doctor before
using the appliance.
'RQRWXVHDWHDWRZHORUVLPLODUPDWHULDOVLQSODFHRIDSRWKROGHU6XFKFORWKVFDQ
FDWFKILUHRQDKRWEXUQHU
When using glass cookware, make sure it is designed for top plate cooking.
■ To minimise the possibility of burns, ignition of flammable materials and spillage, turn
cookware handles toward the side or center of the top plate without extending over
adjacent burners.
■ Always turn burner controls off before removing cookware.
■ Carefully watch foods being fried at a high flame setting.
■ Always heat fat slowly and watch as it heats.
■
■
Foods for frying should be as dry as possible. Frost on frozen foods or moisture on fresh
foods can cause hot fat to bubble up and over the sides of the pan.
Never try to move a pan of hot fat,especially a deep fat fryer.Wait until the fat is
completely cool.
Only ever use the burners after placing pots and pans on them. Do not heat up any empty
pots or pans.
■ Never use plastic or aluminium foil dishes on the appliance.
■ When using other electrical appliances, ensure the cable does not come into contact with
the appliance surfaces of the cooking appliance.
■

Cleaning and Service
Environmental information
unusable, by cutting off the cable.
disposed with other household wastes at the end of its working life. To prevent
possible harm to the environment or human health from uncontrolled waste disposal,
please separate this from other types of wastes and recycle it responsibly to promote
the sustainable reuse of material resources.
agents.
Warning
and cooled.
clean the appliance.
or serviced by an authorised Service
Engineer and only genuine approved
spare parts should be used.
Caution
8
■ Never use abrasive or caustic cleaning ■ This appliance should only be repaired
■ Before attempting to clean the appliance, it should be disconnected from the mains
■ You should not use a steam jet or any other high pressure cleaning equipment to
■ After installation, please dispose of the packaging
with due regard to safety and the environment.
■ When disposing of an old appliance, make it
■ This marking shown on the product or its literature, indicates that it should not be
■ Household users should contact either the retailer where they purchased this product,
or their local government office, for details of where and how they can take this item
for environmentally safe recycling.
■ Business users should contact their supplier and check the terms and conditions of
the purchase contract. This product should not be mixed with other commercial
wastes for disposal.
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)

9
Pot placement tips
■Warning symbols for toughened glass gas hob
■
■ Do not remove the pan support and enclose the
burner with a wok stand as this will concentrate
and deflect the heat onto hotplate.
■
■
■
Do not place anything e.g.flame tamer asbestos
mat between pan and support as serious damage
to the appliance may result.
Do not use large pots or heavy weights which can
bend the pan support or deflect the flame onto the
hotplate.
Locate pan centrally over the burner so that it is
stable and does not overhang the appliance.
Use only a wok support supplied recommended by
the manufacturer of the appliance.

10
Description of the appliance
(G110 1000/
Model Top Plate supply
ΣQn
Glass
760*460*50mm 8.0kW 7.6kW
DC1.5V
Glass
860*510*50mm 9.75kW 9.6kW
Dimension
(W*D*H)
Ignition
device (G20 2000/
G30 2900)
ΣQn
Burner
Feature
Triple-
Crown(2)
Stainless
Steel Continuous
Ignition
Type
Triple-
Crown(2),
Semi-
rapid (1)
Stainless
Steel
TG
NG/LPG

A
How to use the appliance
ccessories
Description of the appliance
11
The following symbols will appear on the control panel, next to each control handle :
Bracket(3)Sponge(4)
Screw(3)Operating/Installation
Manual(1)
Battery(1)
Black circle: gas off
Large flame: maximum setting
Small flame: minimum setting
Automatic ignition with flame failure safety device
The appliance is fitted with a flame failure safety device on each burner, which
is designed to stop the flow of gas to the burner head in the event of the flame
going off.
The minimum setting is at the end of the anti-clockwise rotation of the control handle.
All operation positions must be selected between the maximum and minimum position.
The symbol on the control panel,next to the control handle will indicate which burner it
operates.
Star：Discharge ignition
Wok/Pan support(1)

How to use the appliance
"SCHOTT" logo is only a supplier of glass parts.
To ignite a burner:
oPress in the control knob of the burner that you wish to light and turn it
anti-clockwise to the maximum position.
oIf you keep the control knob depressed, the automatic ignition for the
burner will operate.
o
o After this 5-second interval, to regulate the flame you should continue
turning the control knob anti-clockwise until the flame is at a suitable level.
The operating position MUST be at a position between the maximum and
minimum position.
oTo switch the burner off, turn the control knob fully clockwise to the gas
off position.
oIn case of auto ignition failure, the burners can be lit by carefully using a
gas lighter.
You should hold down the control knob for 5 seconds after the flame on
the burner has lit. If after 15s the burner has not lit, stop operating the
device and open the compartment door and/or wait at least 1 min before
attempting a further ignition of the burner.
o
oOnly for FH-GS6020/6030 SVGL.
Burner ON，large flame Burner ON，small flame
（saving mode）
Burner OFF
FH-GS6030
FH-GS6020
12

Safety and Energy saving advice
- The diameter of the bottom of the pan should correspond to that of the burner.
BURNERS
200mm 240mm
160mm
NO YES
180mm
13
Triple-Crown
Semi-Rapid
PANS
min. max.
Do not use small diameter cookware on large
burners.
The flame should never come up the sides of
the cookware.
Avoid cooking without a lid or with the
lid half off
-as this wastes energy
Do not use a pan with a convex or
concave bottom.
Do not place cookware on one side of a
burner,as it could tip over.
Do not use cookware with a large diameter
on the burners near the controls,which when
placed on the middle of the burner may
touch the controls or be so close to them
that they increase the temperature in this
area and may cause damage.
Never place cookware directly on top of the
burner.
Do not place anything,eg.flame
tamer,asbestos mat,between pan and pan
support as serious damage to the appliance
may result.
Do not use excessive weight and do not
hit the cooktop with heavy objects.
Always use cookware that is
suitable for each burner, to avoid
wasting gas and discolouring the
cookware.
Place a lid on the cookware.
Only use pots,saucepans and
frying pans with a thick,flat
bottom.
Always place the cookware right
over the burners,not to one
side.
Place the cookware on top of
the trivet.
Handle cookware carefully when
they are on the burner.
Ŷ'RQRWXVHFRRNZDUH
WKDW
 
RYHUODSVWKHHGJH of the
burner.
It is not recommended to use roasting pans,frying pans or grill stones
heated simultaneously on several burners because the resulting heat
build-up may damage the appliance.
Do not touch the top plate and trivet whilst in use for a certain period
after use.
As soon as a liquid starts boiling,turn down the flame so that it will
barely keep the liquid simmering.

Soft cloth
Neutral Detergent
Nylon Brush
14
Edible Oil
Abrasive
Detergent
Thinner/Benzene
Metal Brush
Acidic/Alkali
■ Take off the Pan support.
■ Clean these and the control handles with a damp cloth, washing up liquid and warm
water. For stubbon soiling, soak beforehand.
■ Dry everything with a clean soft cloth.
3DQVXSSRUW&RQWUROKDQGOHV
■ Regularly wipe over the top plate using a soft cloth well rung-out
in warm water to
which a little washing up liquid has been added.
■ Dry the top plate thoroughly after cleaning.
■ Thoroughly remove salty foods or liquids from the hob as soon as possible to avoid
the risk of corrosion.
■ Stainless steel parts of the appliance may become discoloured over time. This is
normal because of the high temperatures. Each time the appliance is used these
parts should be cleaned with a product that is suitable for stainless steel.
7RSSODWH
Ŷ &OHDQLQJRSHUDWLRQVPXVWRQO\EHFDUULHGRXWZKHQWKHDSSOLDQFH is
completely cool.
ŶTurn off your gas supply before commencing any cleaning process.
Ŷ&OHDQWKHDSSOLDQFHUHJXODUO\SUHIHUDEO\DIWHUHDFKXVH
Ŷ$EUDVLYHFOHDQHUVRUVKDUSREMHFWVZLOOGDPDJHWKHDSSOLDQFHVXUIDFH
\RXVKRXOGFOHDQLWXVLQJZDWHUDQGDOLWWOHZDVKLQJXSOLTXLG
ŶRegarding the burn cap,it may rust when it is not used for a long time.
Cleaning and Maintenance

Cleaning and Maintenance
15
21
3
4
5
6
7
1.Place the flame spreader ( 4 ) on to the burner cup ( 5 ) so that the ignition device ( 6 )
and the flame supervision device ( 7 ) extend through their respective holes in the
flame spreader.The flame spreader must click into place correctly.
2.Position the burner cap ( 1,2,3 ) onto the flame spreader ( 4 ) so that the retaining
pins fit into their respective recesses.
■ Remove the burner cap and Flame Spreaders by pulling them upwards and away
from the top plate.
■ Soak them in hot water and a little detergent or washing up liquid.
■ After cleaning and washing them, wipe and dry them carefully. Make sure that the
flame holes are clean and completely dry.
■ Wipe the fixed parts of the burner cup with a damp cloth and dry afterwards.
■ Gently wipe the ignition device and flame supervision device with a well wrung-out
cloth and wipe dry with a clean cloth.
■ Before placing the burners back on the top plate, make sure that the injector is not
blocked.
%851(56
ʄ5HDVVHPEOHWKH6HPL5DSLGDQG 7ULSOH&URZQEXUQHUVDV
5HSODFHSDUWVLQWKHFRUUHFWRUGHUDIWHUFOHDQLQJ
'RQRWPL[XSWKHWRSDQGERWWRP
7KHORFDWLQJSLQVPXVW¿WH[DFWO\LQWRWKHQRWFKHV
IROORZV

Warnings
Using instructions
16
Ŷ'RQRWPRGLI\WKLVDSSOLDQFH
Ŷ7KLVDSSOLDQFHPXVWEHLQVWDOOHGE\DQDXWKRULVHGWHFKQLFLDQRU
LQVWDOOHU
Ŷ3ULRUWRLQVWDOODWLRQHQVXUHWKDWWKHORFDOGLVWULEXWLRQFRQGLWLRQV
QDWXUHRIWKHJDVDQGJDVSUHVVXUHDQGWKHDGMXVWPHQWRIWKH
DSSOLDQFHDUHFRPSDWLEOH
Ŷ7KHDGMXVWPHQWFRQGLWLRQVIRUWKLVDSSOLDQFHDUHVWDWHGRQWKHODEHO
RUGDWDSODWH
Ŷ7KLVDSSOLDQFHLVQRWFRQQHFWHGWRDFRPEXVWLRQSURGXFWVHYDFXDWLRQ
LQVWDOODWLRQUHJXODWLRQV3DUWLFXODUDWWHQWLRQ VKRXOG  EHJLYHQ WRWKH
UHOHYDQWUHTXLUHPHQWVUHJDUGLQJYHQWLODWRQ
Ŷ%HIRUHLQVWDOOLQJWXUQRIIWKHJDV.
Ŷ(QVXUHWKDWWKHJDVSLSHisLQVWDOOHGLQVXFKD ZD\WKDWWKH\GRQRW
Ŷ*DVSLSHRUFRQQHFWRUVKRXOGQ¶WEHEHQWRUEORFNHGE\DQ\RWKHU
DSSOLDQFHV
Ŷ&KHFNWKHGLPHQVLRQVRIWKHDSSOLDQFHDVZHOODVWKHGLPHQVLRQVRI
WKHJDSWREHFXWLQWKHNLWFKHQXQLW
Ŷ7KHSDQHOVORFDWHGDERYHWKHZRUNVXUIDFHGLUHFWO\QH[WWRWKH
DSSOLDQFHPXVWEHPDGHRIQRQÀDPPDEOHPDWHULDO%RWKWKHVWUDWL
¿HGVXUIDFLQJDQGWKHJOXHXVHGWRVHFXUHLWVKRXOGEHKHDWUHVLVWDQW
WRSUHYHQWGHWHULRUDWLRQ
Ŷ7XUQRQDSSOLDQFHWDSDQGOLJKWHDFKEXUQHUV
&KHFNIRUDFOHDUEOXHÀDPHZLWKRXW\HOORZWLSSLQJ
,IEXUQHUVVKRZVDQ\DEQRUPDOLWLHVFKHFNWKHIROORZLQJ
%XUQHUOLGRQFRUUHFWO\
)ODPHVSUHDGHUSRVLWLRQHGFRUUHFWO\
%XUQHUYHUWLFDOO\DOLJQHGZLWKLQMHFWRUQLSSOH
Ŷ$IXOORSHUDWLRQDOWHVWDQGDWHVWIRUSRVVLEOHOHDNDJHVPXVWEHFDUULHG
RXWE\WKHinstallerDIWHUinstallation
Ŷ7KHÀH[LEOHKRVHVKDOOEH¿WWHGLQVXFKDZD\WKDWLWFDQQRWFRPHLQWR
FRQWDFWZLWKDPRYHDEOHSDUWRIWKHKRXVLQJXQLWDQGGRHVQRWSDVV
WKURXJKDQ\VSDFHVXVFHSWLEOHRIEHFRPLQJFRQJHVWHG
GHYLFH,WVKRXOG be installed and connected in accordance with current
Grease cranes produced at the factory to meet the requirement of all
gas hob.
Ŷ
touch any parts of the appliance which may become hot.

Positioning
The edges of the hob must be a minimum distance of mm from a side or
rear wall.
At least 750 mm between the highest point of the hob surface (including the
burners) and the underside of any horizontal surface directly above it.
400 mm between the hob surfaces, providing that the underside of the
horizontal surface is in line with the outer edge of the hob. If the underside of
the horizontal surface is lower than 400 mm, then it must be at least 50 mm
away from the outer edges of the hob.
50 mm clearance around the appliance and between the hob surface and any
combustible materials.
50mm
60
You must have a gap of at least 25 mm and at most 74 mm between
the underneath of the appliance and any surface that is below it.
17
o
o
o
o
o
This appliance is to be built into a kitchen unit or 600mm worktop,providing
the following minium distances are allowed;
- An oven must have forced ventilation to install a hob above it.
- Check the dimensions of the oven in the installation manual.
- The cut out size must obey the indication.
4-R60
FA
RA
650-720mm
345-420mm
≈ 600
4-R60
FA
RA
685-820mm
385-470mm
≈ 600
FH-GS6020 SVGL/SVSS FH-GS6030 SVGL/SVSS
≥750mm
400mm
400mm
≥750mm
400mm
400mm
Model
FH-GS6020 SVGL W650xD350
W705xD405
FA25xRA95 W(650-720)xD(345-420)xR60 50
50FA25xRA100 W(685-820)xD(385-470)xR60
FH-GS6020 SVSS
FH-GS6030 SVGL
FH-GS6030 SVSS
Cut Out Dimension(mm) Replacement size(mm) Height(mm)

Installing the appliance
Sponge
Bottom view The thickness of the sponge is 3 mm.
The width of the sponge is 10 mm.
Place the bracket (B) over the holes that match the size
of the screws.There are one set of screw holes (H) in
each corner of the hob.
Slightly tighten a screw (C) through the bracket (B) so
that the bracket is attached to the hob, but so that you
can still adjust the position
.
.2 Carefully turn the hob back over and then gently lower
it into the aperture hole that you have cut out.
.3 On the underneath of the hob, adjust the brackets into
a position that is suitable for your worktop.
Then fully tighten the screws (C) to secure the hob into
position.
(C) SCREW (B) BRACKET
18
(A) SEALING STRIP
(H) SCREW HOLES
Remove the pan supports, the burner
cap and flame spreader and carefully turn
the appliance upside down and place it
on a cushioned mat.
Take care that the Ignition devices and
flame supervision devices are not damaged
in this operation.
2. Apply the sponge provided around the
edge of the appliance.
3.
1.
Do not leave a gap in the sealing agent or
overlap the thickness.
1.
7KLVZLOOPDNHLWGLI¿FXOWWRUHPRYHWKH
DSSOLDQFHIURPWKHDSHUWXUHLQIXWXUH
SDUWLFXODUO\LILWQHHGVWREHVHUYLFHG
Do not use a silicon sealant to seal the
appliance against the aperture.
FH-GS6030 SVGL/SVSS FH-GS6020 SVGL/SVSS
CAUTION: In case of hotplate glass breakage:
- shut immediately off all burners and any electrical heating element and isolate the
appliance from the power supply
- do not touch the appliance surface,
- do not use the appliance.
This appliance is not connected to a combustion products evacuation
device. It shall be installed and connected in accordance with current
installation regulations. Particular attention shall be given to the relevant
requirements regarding ventilation

Inlet gas connection
19
Important:
■ The appliance should be installed, regulated and adapted to function with other
types of gas by a QUALIFIED INSTALLATION TECHNICIAN.
■The appliance is fitted with specified gas type as shown in the specification
nameplate and cannot be used or converted to any other type of gas.
Installation:
■ The appliance is predisposed and adjusted to operate with the gas indicated
on the specifications nameplate located at the bottom of the appliance.
Please ensure that the intended gas type used corresponds with that
specified on the nameplate.
Gas connection for gas hob:
■ The appliance should be connected to the gas-supply by licensed installer.
During installation of this appliance , it is essential to fit an approved gas tap
to isolate the supply from the appliance for the convenience of any subsequent
removal or servicing. Connection of the appliance to the gas mains or liquid
gas must be carried out according to the prescribed regulation in force, and
only after it is ascertained that it is adaptable to the type of gas to be used.
In the case of connection to liquid gas, by tank, use pressure regulators
that conform to the regulation in force. Connection to the gas course must
be done in such a way that not to create any stress points any part of the
appliance.
IMPORTANT: For safety, for the correct regulation of gas use and long life of
the appliance, ensure that the gas pressure conforms to the indications given
in table 1 “ Nozzle and burner characteristics" .
Installation instructions for fixing gas cooker elbow joint :
The gasket depicted above is to prevent gas leakage. After installation, turn on the
■
gasket intake pipe of the
whole machine
elbow joint
gas source
connector
gas supply and use soap solution (never use naked flame) to check for gas leakage.
When NG/TG is installed, the connection installation is shown in the figure: