Fujitsu L21T-1 User manual

Operating Manual Display
FUJITSU Display L21T-1

Congratulations on your purchase of an innovative
product from Fujitsu.
Latest information about our products, tips, updates etc. can be found on the Internet at:
http://www.fujitsu.com/fts/
For driver updates, please go to: http://support.ts.fujitsu.com/download
Should you have any technical questions, please contact:
●our Hotline/Service Desk (see Service Desk list or visit:
http://support.ts.fujitsu.com/contact/servicedesk)
●your sales partner
●your sales office
We hope you enjoy working with your new Fujitsu system!

Published by / Contact address in the EU
Fujitsu Technology Solutions GmbH
Mies-van-der-Rohe-Straße 8
80807 Munich, Germany
http://www.fujitsu.com/fts/
Copyright
© Fujitsu Technology Solutions GmbH 2015. All rights reserved.
Publication Date
07/2015
Order No.: A26361-K1575-Z320-1-7619, edition 1

FUJITSU Display L21T-1
Operating Manual
First Setup 2
Quick Installation 3
Installing the LCD 5
Front view of the product 7
Rear view of the product 8
Using On Screen Display (OSD) 9
Supporting Timing Modes 13

Remarks
Information on the product description meets the design specifications of Fujitsu and is
provided for comparison purposes. Several factors may cause the actual results to differ.
Technical data is subject to change without prior notification. Fujitsu rejects any responsibility
with regard to technical or editorial mistakes or omissions.
Trademarks
Fujitsu and the Fujitsu logo are registered trademarks of Fujitsu Limited or its subsidiaries in
the United States and other countries.
Microsoft and Windows are trademarks or registered trademarks of the Microsoft Corporation
in the United States and/or other countries.
VESA, DDC and DPMS are registered trademarks of Video Electronics Standards
Association.
All other trademarks specified here are the property of their respective owners.
Copyright
No part of this publication may be copied, reproduced or translated without the prior written
consent of Fujitsu.
No part of this publication may be saved or transferred by any electronic means without the
written approval of Fujitsu.

Contents
Contents
First Setup........................................................................................................................................... 2
Quick Installation................................................................................................................................3
Installing the LCD monitor................................................................................................................. 5
Assembling the stand and base ........................................................................................................... 5
Disassembling the stand and base....................................................................................................... 6
Front view of the product................................................................................................................... 7
Rear view of the product.................................................................................................................... 8
Using On Screen Display (OSD) functions....................................................................................... 9
Main Menu............................................................................................................................................ 9
Shortcut functions from the button(s) ................................................................................................. 10
Automatic adjustment................................................................................................................. 10
Adjusting brightness and contrast .............................................................................................. 10
Adjusting the input...................................................................................................................... 10
Adjusting the audio functions ..................................................................................................... 10
Adjusting the colour.................................................................................................................... 11
Displaying information ................................................................................................................ 11
Adjusting the image.................................................................................................................... 11
Adjusting the OSD setup ............................................................................................................ 12
Adjusting the factory settings ..................................................................................................... 12
Supporting Timing Modes ............................................................................................................... 13
Warning .............................................................................................................................................. 13
Fujitsu 1

First Setup
First Setup
Congratulation for purchasing monitor! This monitor comes with the following accessories:
• Power cable
• Audio cable
• DVI cable (24 pin)
• Quick Start Guide
• Safety manual
2 Fujitsu

Quick Installation
Quick Installation
1 32 4 5
1 = Power cable
2 = Headphones (optional)
3 = DVI cable
4 = AUDIO cable (optional)
5 = VGA cable
►Make sure that both monitor and computer are OFF.
►Connect the video cable (VGA cable) to the computer, then to the monitor.
►Connect the DVI cable from the DVI output on the computer to the DVI input on the monitor.
►Connect the power cable to a properly grounded AC outlet, then to the monitor.
►Connect the headphones to the headphone output terminal of the monitor (headphones sold
separately).
►Connect the audio cable from the audio output of your computer to the audio input of the
monitor.
►Turn the computer power on.
►Turn the monitor power on.
Fujitsu 3

Quick Installation
►Set the timing mode (resolution and refresh rate):
For Windows users
Example: 1920 x 1080 @ 60 Hz
Resolution
– Right-click on the Windows desktop and select Screen Resolution.
– Set the resolution.
Refresh rate (vertical frequency)
– See your graphic card’s user guide for instructions.
4 Fujitsu

Installing the LCD monitor
Installing the LCD monitor
Assembling the stand and base
►To prevent the monitor from being scratched, put a piece of soft cloth on the table on which the
screen will be put.
►Lay the monitor flat on a table with the LED screen face down.
►Insert the stand and base into the monitor as shown below.
►Stand the LED LCD monitor on its base.
Fujitsu 5

Installing the LCD monitor
Disassembling the stand and base
►To prevent the monitor from being scratched, put a piece of soft cloth on the table on which the
screen will be put.
►Lay the monitor flat on a table with the LED screen face down.
►Press the release button and pull the stand away from the monitor.
►Push the tabs inwards and pull the base from the stand to remove.
6 Fujitsu

Front view of the product
Front view of the product
1234 65
1 = OSD menu ON/OFF
2 = Scroll down / Decrease
3 = Scroll up/ Increase
4 = Confirm/Select
5 = Power ON/OFF
6 = LED indicator
Fujitsu 7

Rear view of the product
Rear view of the product
1234 5
1 = Power input
2 = Headphone jack
3 = Audio input
4 = DVI input (DVI 24 pin)
5 = VGA input (D-Sub 15 pin)
8 Fujitsu

Using On Screen Display (OSD) functions
Using On Screen Display (OSD) functions
Displays main menu1
Exits OSD menu
Toggles between VGA or DVI2
Confirms selection
Selects the desired item when in OSD menu▼
When not in OSD menu, opens the Brightness/Contrast menu
Selects the desired item when in OSD menu▲
When not in OSD menu, directly enters Image Mode
1+▼Power lock (when not in OSD menu)
1+▲OSD lock (when not in OSD menu)
Main Menu
Fujitsu 9

Using On Screen Display (OSD) functions
Shortcut functions from the button(s)
Automatic adjustment
Automatically adjusts Horizontal Position, Vertical Position,
Phase (Fine Tune) and Clock (H. Size) of the screen.
Adjusting brightness and contrast
Calls up the Brightness/Contrast setting window
Contrast Adjusts the contrast of the screen.
▲: Increase contrast.
▼:Decrease contrast.
Brightness Adjusts the brightness of the screen.
▲: Increase brightness.
▼:Decrease brightness.
ACR Allows the user to turn ACR on or off. Brightness adjustment
and ECO are disabled when ACR is active.
ECO Allows the user to turn ECO on or off. Brightness adjustment
and ACR are disabled when ECO is active.
Adjusting the input
When Input Select is selected, change the input signal to VGA
or DVI.
Adjusting the audio functions
Adjusts the audio functions.
Volume Adjusts the speaker output volume.
Mute Turns the Mute on or off.
10 Fujitsu

Using On Screen Display (OSD) functions
Adjusting the colour
Selects the color to improve brightness and colour saturation
between 9300K, 6300K, 5400K and customer colour.
9300K Adds more blue to the picture, for a cooler white.
6300K Adds more red to the picture, for a warmer white and richer
reds.
5400K Adds more green to the picture, for darker tones.
Customer color Individual adjustments for red (R), green (G), blue (B).
►Press button 2 to select the desired colour.
►Press the ▲or ▼button to adjust the selected colour.
Displaying information
Displays the information regarding the current input signal
coming from the graphic card in your computer.
Note: See your graphic card user guide for more information
about changing the resolution and refresh rate.
Adjusting the image
Manually adjusts the H./V. position, horizontal size, phase,
sharpness, expansion and mode
H./V. Position Adjusts the horizontal and vertical position of the image.
H. Position ▲: Move screen to the right.
▼:Move screen to the left.
V. Position ▲: Move screen up.
▼:Move screen down.
Horizontal size Adjusts the width of the screen image.
▲:Increase the width of screen image.
▼:Decrease the width of screen image.
Phase Adjusts the delay time of data and clock.
Press ▲or ▼to adjust to your preference.
Sharpness Adjusts the clarity of a non-Full HD resolution (1920 x 1080)
signal with the ▲or ▼button.
Expansion Toggles the video mode between Full Screen or Aspect
Ratio
Full Screen Selects full-screen image.
KeepAspect Selects input timing image size.
Fujitsu 11

Using On Screen Display (OSD) functions
Mode Provides an optimum display environment depending on the
contents displayed. It contains 5 user-selectable presets.
Standard is for the general Windows environment and the monitor
default setting.
Game optimised for a PC game environment
Video optimised for a movie and video environment.
Landscape optimised to display outdoor scenery images.
Text optimised for text editing and viewing in a word processing
environment
Adjusting the OSD setup
Sets Language, OSD Position, OSD time Out and OSD
Background.
Language Allows users to choose from the languages available.
OSD Position Press the ▲or ▼button to toggle between horizontal and
vertical OSD position adjustment.
H. Position Horizontally adjusts the OSD position.
▲:Move OSD to the right.
▼:Move OSD to the left.
V. Position Vertically adjusts the OSD position.
▲: Move OSD up.
▼:Move OSD down.
OSD time Out Automatically turns off On Screen Display (OSD) after a
preset period of time.
OSD Background Allows the user to turn the OSD background ON or OFF.
Adjusting the factory settings
Restores factory settings for Video or Audio controls.
Press button 2 to select the Memory Recall menu option.
12 Fujitsu

Supporting Timing Modes
Supporting Timing Modes
Resolution Refresh rate
640 x 480 60/67/72/75Hz
720 x 400 70 Hz
800 x 600 60/75 Hz
832 x 624 75 Hz
1024 x 768 60//70/75 Hz
1280 x 800 60 Hz
1280 x 960 60 Hz
1280 x 1024 60/75 Hz
1152 x 864 75 Hz
1152 x 870 75 Hz
1440 x 900 60/75 Hz
1600 x 1200 60 Hz
1680 x 1050 60 Hz
1920 x 1080 60 Hz
!
Do not set the graphic card in your computer to exceed these maximum refresh
rates. Doing so may result in permanent damage to your monitor.
Warning
!
This display is equipped with a glossy front bezel.
Please consider the placement of the display as the front bezel may cause reflections from
surrounding light and bright surfaces.
Fujitsu 13