Fujitsu Eternus DX80 S2 Manual

ETERNUS DX80 S2 and DX90 S2
Hardware Installation
Copyright Fujitsu Technology Solutions, Release August 2011
Hardware Installation ETERNUS DX80 S2 and DX90 S2

Package Contents
Rack Mounting
Power Cabling
Backend Cabling QSFP
Power On Procedure
Power Off Procedures
Operator Panel -Function Button
Hardware Installation ETERNUS DX80 S2 and DX90 S2 Copyright Fujitsu Technology Solutions, Release August 2011
Content
1

Package Contents (1)
Controller Enclosure Kit
Installation poster
Documentation CD
Rack mount kit
Controller Enclosure
•Single Controller Module
•Dual Controller Module
Left and right Flange Cover
Push pin tool
2 x power cords
Safety Manual
Copyright Fujitsu Technology Solutions, Release August 2011
Hardware Installation ETERNUS DX80 S2 and DX90 S2 2

Package Contents (2)
Drive Enclosure Kit
Installation poster
Rack mount kit
Drive Enclosure
2 x power cords
1 x QSFP (SAS) cable
•Single IOM configuration
2 x QSFP (SAS) cables
•Dual IOM configuration
Safety Manual
Copyright Fujitsu Technology Solutions, Release August 2011
Hardware Installation ETERNUS DX80 S2 and DX90 S2 3

Rack Mounting (1)
For FTS (CEMEA &I) only
Rack-mount kit
Rack mount installation overview
Copyright Fujitsu Technology Solutions, Release August 2011
Hardware Installation ETERNUS DX80 S2 and DX90 S2 4

M5 Centering
screws (10 mm)
2U Bracket
Rack Mounting (2)
Attach the 2U Bracket to the right rear
rack pillar
The M5 centering screws should be
inserted in the 1st and 6th holes
above the base line of the
Enclosures
Insert the pins of the left hand
side slide rail in the 1st and
3rd hole
Start counting from the bottom
of the 2U Bracket
Copyright Fujitsu Technology Solutions, Release August 2011
Hardware Installation ETERNUS DX80 S2 and DX90 S2
Base line of the
Controller Enclosure
5

M5 Cage nut
Rack Mounting (3)
Push the M5 cage nut into the
2nd hole of the front rack pillar
Above the base line of the Enclosures
At the left hand side fix the slide
rail to the front pillar with
The M5 centering screws
The M5 pan head screws
Copyright Fujitsu Technology Solutions, Release August 2011
Hardware Installation ETERNUS DX80 S2 and DX90 S2
M5 Centering
screw (10 mm)
M5 Pan head
screw (10 mm)
Base line of the
Controller Enclosure
6

Rack Mounting (4)
For the left hand side rail
Insert the pins in the holes of the rear pillar
Fix the other side of the slide rail to the front pillar
•Repeat the same procedure as done before with the left hand side slide rail
Copyright Fujitsu Technology Solutions, Release August 2011
Hardware Installation ETERNUS DX80 S2 and DX90 S2
Base line of the
Controller Enclosure
M5 Cage nut
Base line of the
Controller Enclosure M5 Pan head
screw (10 mm)
M5 Centering
screw (10 mm)
7

Rack Mounting (5)
Front view of the rack installation
Copyright Fujitsu Technology Solutions, Release August 2011
Hardware Installation ETERNUS DX80 S2 and DX90 S2 8

Rack Mounting (6)
Fit the Controller Enclosure and/or Drive Enclosure to the rack
For better stability, a rack has to be filled by starting from the
bottom
Copyright Fujitsu Technology Solutions, Release August 2011
Hardware Installation ETERNUS DX80 S2 and DX90 S2 9

Power Cabling
Copyright Fujitsu Technology Solutions, Release August 2011
Hardware Installation ETERNUS DX80 S2 and DX90 S2
For FTS (CEMEA&I) only
Connect the rack PDUs
(Power Distribution Units) to
independent AC power phases
Make sure that the AC
power switches on each
Enclosure are turned off before
connecting their power cables
Connect each Power Supply
of an Enclosure to different
Power Distribution Units
PSU#0 inlet PSU#1 inlet
PSU#0
inlet PSU#1
inlet
Left
Rack PDU Right
Rack PDU
Always follow the local
power cabling regulations!
10

Backend Cabling QSFP (1)
SAS Port at the CM or IOM6 (SAS Expander)
Connect SAS (OUT) ports and SAS (IN) ports by daisy-chain
Start in ascending order from the Controller Enclosure
Copyright Fujitsu Technology Solutions, Release August 2011
Hardware Installation ETERNUS DX80 S2 and DX90 S2
Drive Enclosure# 02
Drive Enclosure #01
Controller Enclosure
11

Backend Cabling QSFP (2)
Follow the SAS port labels at the Enclosures
This will point to the correct cabling
This sign means "IN" and this sign means "OUT"
Connect the cables according the labels showing direction ( and )
SAS ports of the Controller Enclosure always have the type "OUT"
Copyright Fujitsu Technology Solutions, Release August 2011
Hardware Installation ETERNUS DX80 S2 and DX90 S2
Connect with
the port where
is indicated
Connect with
the port where
is indicated
DE
CE
OUT IN
Cable symbol
OUT
12

Backend Cabling QSFP (3)
QSFP connection between racks
To connect QSFP cable between two racks an expansion cable of 3 or 6
meters is used
Copyright Fujitsu Technology Solutions, Release August 2011
Hardware Installation ETERNUS DX80 S2 and DX90 S2 13

Single / Dual Controller Update
A single CM configuration is allowed to be upgraded to a
dual CM configuration in the field
Also the Drive Enclosure need to be upgraded
Copyright Fujitsu Technology Solutions, Release August 2011
Hardware Installation ETERNUS DX80 S2 and DX90 S2
CE
CM #0
DE
IOM6
DE
IOM6
CE
DE
IOM6
DE
IOM6
IOM6
IOM6
Single CM Dual CM
CA CA
CM#0
CA CA
CM#1
CA
CA
1 CM to 2 CM upgrade parts
CA: ChannelAdapter
IOM:IO module
DE: Device Enclosure
14

Power On Procedure (1)
The ETERNUS DX S2 systems can be Powered On directly
from the Controller Enclosure
Push the Power Switch
•The "Power" LED of the CE switches on
•The power on sequence takes about 2 minutes
•If everything is OK, the green Ready LED in
the CE and the green Power LED in the DE
switch on
Copyright Fujitsu Technology Solutions, Release August 2011
Hardware Installation ETERNUS DX80 S2 and DX90 S2
Power O
Fault O
Active O
Power O
Ready O
Fault O
Maint/ID O
Cache O
15

Power On Procedure (2)
Controller Enclosure LEDs
Copyright Fujitsu Technology Solutions, Release August 2011
Hardware Installation ETERNUS DX80 S2 and DX90 S2
POWER LED
Constant green when the power is turned on
READY LED
Constant green when device is available
for use
FAULT LED
Constant amber when a failure is detected
in the ETERNUS DX system
Blinks in amber when a component which
requires preventive maintenance is detected
MAINT/ID LED
Constant green when the system has its
status set to Maintenance
Blinks green
Status of all components needs to be
verified with the GUI or CLI
Locate functionality enabled by the GUI
or CLI
CACHE LED
Constant green when data exists in cache memory
Blinks in green when cached data is saved to the flash memory
16

Power On Procedure (3)
Drive Enclosure LEDs
Copyright Fujitsu Technology Solutions, Release August 2011
Hardware Installation ETERNUS DX80 S2 and DX90 S2
LINE LED
AC power is supplied to the Drive Enclosure
FAULT LED
Constant amber when a failure is detected
in the Drive Enclosure
POWER LED
The Drive Enclosure is operating normally
DE-ID (7-segment)
Shows a 2-digit Drive Enclosure ID
Is assigned automatically by the SAS
backend cabling
2.5" Drive Ecnlosure
3.5" Drive Ecnlosure
17

Power Off Procedure
Verify with the customer that all server I/O is stopped
Also confirm that the "CACHE" LED in the Operator Panel is off
Hold down the "Power Switch" of the Controller Enclosure for
approximately 5 seconds
The ETERNUS DX system will shutdown all Enclosures gracefully
In case of moving ETERNUS to a new location, you naturally
have to also disconnect the AC power cords
from the PDUs after the system is
powered off
Copyright Fujitsu Technology Solutions, Release August 2011
Hardware Installation ETERNUS DX80 S2 and DX90 S2
Make sure the CACHE LED
of the Controller Enclosure
is off
18

Operator Panel -Function Button (1)
Remove the plastic Flange Cover to get access to
the Function Button
The Function Button is located
next to the Power Switch
Use the pin tool to operate
Copyright Fujitsu Technology Solutions, Release August 2011
Hardware Installation ETERNUS DX80 S2 and DX90 S2
Function Button
Power Button
2.5" Controller Enclosure 3.5" Controller Enclosure
19