Fulcrum Torbal DRX-4 User manual

Instruction Manual Model:

Instruction Manual Model
Fulcrum Inc.
23 Carol Street.
Clifton, NJ 07014
[phone]
[phone]
http://www.fulcruminc.net

TABLE OF CONTENTS
0
0
0
0
0
0
0
0
0
1
1. Specifications......................................................................
2. Parts Description................................................................ 2
3. Keys and display indicators................................................... 3
4. Commands........................................................................ 4
5. Getting Started.................................................................. 5
6. Weighing........................................................................... 7
7. Zeroing the Scale................................................................ 8
8. Taring.............................................................................. 9
9. Clearing the Tare............................................................... 11
10. Printing............................................................................ 12
11. Calibration........................................................................ 14
12. Sealing the DRX-4............................................................. 17
Paper Seal..............................................................17
Wire Seal............................................................... 18
13. Setting the Time and Date .................................................. 19
14. Common Errors and Troubleshooting.....................................23
13.
14.

I n s t r u c t i o n M a n u a l M o d e l D R X - 4
Specifications:
1
C H A P T E R 1

Parts Description:
2
Front View Rear View
Pan Base Pan AC Adaptor Flush Sealing
Screw
Adjustable Legs
Wire Seal Screws AC Adaptor socket
RS232 Serial Port
Calibration Switch Level Indicator
I n s t r u c t i o n M a n u a l M o d e l D R X - 4
C H A P T E R 2

Keys and display indicators
3
Center of zero NET result indicator
Stabilization indicator Used Capacity Indicator
** In order for the scale to enter and remain in the Standby Mode, the power
supply must be plugged into the scale.
NOTE:
Tare button - used to tare the weighing pan and enter or accept
commands.
Function button - used to enable and disable the printing capability.
Power On/Off button.- when turned “Off” the scale enters Standby
Mode. **
Scale stabilization indicator - signals the weighing result has
stabilized and an accurate reading may be taken.
AZSM - indicates the Auto Zeroing Setting Mechanism (AZSM) is
active. AZSM maintains a center of zero condition within +/- .6d or
6mg
Dotted line on the display indicates the “T” or “0” buttons have been
pressed and the scale is taring or re-zeroing.
Weighing unit (grams).
Print button, used to print or send data to a PC.
Zero button, used to re-zero the scale.
I n s t r u c t i o n M a n u a l M o d e l D R X - 4
C H A P T E R 3

Commands
4
* These commands apply only to the Calibration Mode.
NOTE:
PRINT
CAL
TARING
LOAD 100g
C
CAL FIN
When pressing the “P” button, “PRINT” indicates data is
printing via the serial port.
Indicates the rear calibration switch has been toggled to the
ON position and the scale is in the Calibration Mode.*
Indicates the scale is taring for the calibration procedure to
begin.*
Indicates to load the calibration weight of 100 grams on the
pan to begin calibration.*
The scale is calibrating.*
Calibration procedure is finished.*
I n s t r u c t i o n M a n u a l M o d e l D R X - 4
C H A P T E R 4

Getting Started
5
1. Carefully remove the scale and all of its components from the packaging
and place it on a stable base where the scale will not be affected by any
mechanical vibrations or air movements.
2. After removing the pan base and the pan from its packaging, carefully
install the pan base onto the scale by placing it on the pan support located
in the middle of the scale. Once the pan base has been installed, carefully
place the pan on the base as shown below.
I n s t r u c t i o n M a n u a l M o d e l D R X - 4
C H A P T E R 5