
2015 FMP Inc. All Rights Reserved
C
Mini-Deja’Vibe
MDV-1 Features:
Input Jack: plug guitar into this, or cable coming from the “out” of another effect.
Output Jack: plug cable going to amp into this, or cable going to “input” of another effect.
Intensity Knob: controls the amount of effect (chorus and Vibrato) by increasing (clockwise) or decreasing (counter-clockwise)
the brilliance of the light source circuitry. For faster speeds, reduce the Intensity a bit.
Volume Knob: affects the overall volume of the pedal...but only when the pedal is turned "on."
Speed Knob: this sets the rate of the modulation, and will be reflected visually by the flashing LED.
I gave the MDV an over-sized knob so that you can adjust the speed on-the-fly using your feet.
Speed/Status LED: This bright LED not only tells you when the effect is On, but also pulses at the selected speed so you can visually
sync to the desired tempo.
Chorus/Vibrato switch: When this switch is set to Vibrato you get out of tune pitch-bend vibrato with no phasing. When this switch
is set to Chorus you get the familiar Hendrix/Trower phasing sounds that we all grew up with.
Modern/Vintage switch: Set this switch to Vintage for stock warm “Vintage Univibe” sounds of a darker nature, or set it to Modern for
more output and brightness...great for use with less distorted tones!
Warning! Do not use any voltage other than 18VDC. Your MDV-1 comes with the finest power supply available, the Fulltone FPS-3
(for USA, Japan, & Canada only) 18VDC power supply. You may only use a 18 volt DC supply offering at least 100ma. of current, and using the
standard 2.1mm x 5.5mm barrel connector configured Center-Negative.The symbol for “Center Negative” is the following:
If you use a pedalboard Power supply, make sure to use one that is “Regulated” and has “Isolated outputs” (for example: the Voodoo Lab
PedalPower2) so that exactly 18.0 volts DC is supplied. If you use a non-regulated 18VDC power supply, the unit’s bulb will either be brighter
or dimmer than is recommended and will not perform correctly and may be noisy.
Light Source Trimmer control: Warning! This trimmer allows you to fine-tune the amount of current that gets to the light bulb thus adjusting
the amount of pitch-bend Vibrato and Phasing.This is set at our shop and should not need adjustment but (if need be) should only be adjusted
by someone who understands the nature of the circuit and how the Lightbulb affects the overall sound. The Trimmer is accessible by opening up
the pedal and using a small slotted or Phillips-head screw driver to turn the Trimmer slightly Counter Clock-Wise (CCW)
to DECREASE bulb brightness, increasing the “Phase Swoosh.” Or Turn slightly CW to INCREASE bulb brightness and “Phase Swoosh.”
You have to use your ears, but our optimal setting is marked around the access hole should you want to return to the factory setting.
Warranty: Fulltone products carry a Limited 5 year Warranty to the original owner with proof of purchase the product was bought
from an Authorized Fulltone Dealer. There is no need to register your product, simply keep a copy of your original sales receipt.
The Warranty covers failure due to manufacturing errors only and is void if a mod or repair is attempted by anyone other than Fulltone
(or an Authorized Fulltone Repairman) and/or if we deem that any operator-caused abuse or damage has occurred. Things that would
cause voiding of the Warranty would include: the use of an incorrect power supply, water damage, physical abuse, etc. If you are having
a
technical
issue
please
do
not
call.
Instead,
email
[email protected] to
troubleshoot
the
problem
and
(only
after
troubleshooting)
for
the scheduling of your repair. After we have decided that a repair is necessary, we will email you an Acrobat PDF copy of our Return
Authorization Form. (RA Form) You then print it out, fill out all the information, and include it in the box with the effect you are sending.
Fulltone Musical Products Inc. is not responsible for and injuries and/or damages related to the use of our products. The Customer is
responsible for all shipping costs. Thank you for buying the Fulltone MDV-1!
Fulltone Musical Products Inc.
11018 Washington Blvd. Culver City, CA 90232
for more info and expanded information/videos go to http://www.fulltone.com
for Sales, Techical, or Repair related questions go to www.fulltone.com/contact-us