Furious FPV INNOVA OSD-VTX User manual

INNOVA OSD-VTX Manual User.

Furious FPV INNOVA VTX-OSD board - Small Size, Massive Capability.
As Furious FPV blurs the line of capability, functionality and ultimate user friendliness, our goals
of light weight, compact design and the ultimate in user ease comes into stark focus via our all
new VTx design. Get ready to change the way you FPV with the all new Furious FPV INNOVA
VTX-OSD board
What's being offered? How about an integrated OSD, adjustable 25mW - 200mW VTx, PID
tuning options, battery monitoring, flight timer, and channel configuration via the OSD. Simply
put, the Micro Stack is the perfect solution that fits all your FPV needs in one micro sized
stackable package.
Specifically designed to integrate with the PIKO BLX, this system transforms the PIKO into an
all in one system that rivals all others available today. The synergy between these two systems
offers massive levels of functionality & capability that brings forth every aspect of FPV
technology into a light weight, ultra compact design that fits perfectly within the heart of your
favorite FPV racing machine.
Supported by CleanFlight & BetaFlight, the INNOVA VTX-OSD offers unrivaled levels of FPV
functionality - the perfect pairing when it comes to the PIKO BLX flight controller.
Features:
- Weight: 4.8g
- Number of channels: 40
- Specifically Designed for the PIKO BLX with 20x20mm hole to hole platform
- Fully Adjustable 25mW - 200mW VTx Output
- Raceband Ready Frequency Layout
- PID Tuning Capable
- Built In Battery Status Monitoring
- Integrated Flight Timer System
- VTx Channel Configurable via the OSD
- Connector type: UFL
- UFL to SMA female cable included
Supported FC type:
- Optimized for Piko BLX FC.
- All FC use Betaflight, Cleanflight, RaceFlight, Baseflight.
Band table
T
CH1
CH2
CH3
CH4
CH5
CH6
CH7
CH8
Band A
5865
5845
5825
5805
5785
5765
5745
5725
Band B
5733
5752
5771
5790
5809
5828
5847
5866
Band E
5705
5685
5665
5645
5885
5905
5925
5945
Band F / Airwave
5740
5760
5780
5800
5820
5840
5860
5880
Band C / Raceband
5658
5695
5732
5769
5806
5843
5880
5917

HOW DO TO USE INNOVA OSD-VTX
Installations to flight control:
- Solder Power Selection Pad to use power 5vol from Piko BLX or your FC use
Betaflight. If you use straight power from battery to Innova, you MUST un-solder Power
Selection pad.
- Unsolder Pad DTR to use LED Strip port on Innova. Solder DTR pad for use DTR when
you flash FW by FTDI tool.

Connect Camera and LED strip to Innova:
Guide use Transmitter adjusting quadcopter’s parameter in OSD menu.
To access the in-built OSD menu in MW-OSD, disarm your quadcopter first.
- THROTTLE MIDDLE
- YAW RIGHT
- PITCH FULL
To navigate through menu in the OSD:
- PITCH/ROLL sticks are used to navigate
- YAW stick is used to adjust / change values
OSD Menu Index:
- PID Config (Roll/Pitch/Yaw PID for many flight modes)
- RC Tuning (RC Rate, RC Expo, Pitch/Roll Rate, Yaw Rate, TPA (Throttle PID Att)
- Voltage (Display voltage on/off, Adjust Voltage, Voltage alarm, Cells)
- RSSI (Display RSSI on/off etc)
- Current (Display Amp on/off, Adjust Amps)
- Advanced (Unit –Metric or Imperial, Signal –Pal or NTSC, Mag Calibration)
- Display (On/Off switches for Horizon, Sidebars, Scrolling bars, Throttle, GPS Coordinates,
Sensors, Gimbal, Map Mode)
- Statistics (Trip, Maximum Distance, Max Altitude, Max Speed, Flying time).

Guide use Betaflight configure Innova:
That means that if you need to change the settings on your OSD or update the firmware you don’t
need to dismantle your quad to access the OSD, you simply need to enable serial passthrough
within cleanflight/betaflight.
The only thing is that for now you need to do this via the CLI.
- Step 1: Connect Flight controller connected with Innova VTX-OSD to cleanflight/betaflight
and click Connect.
- Step 2: Open Port Tab, turn on MSP of UART port connecting with Innova.
And click Save and Reboot button.
- Step 3: Go to CLI, and type the following: serialpassthrough (port) (baud)

NOTE: Betaflight labels serial port starting from 0 not 1 yet most flight controller label UART’s starting
with 1. So when selecting your serial port you will typically take whatever the UART number is and
subtract 1 to get the serial port it’s asking for.
EX: you have your Innova VTX-OSD connected UART1 that you want to connect to you will need to type:
serialpassthrough 0 11500
Step 4: Power up the device you are trying to connect to if it’s not already
You will see what looks like random characters start scrolling under the command you ran if it’s working
properly.
NOW YOU CAN CONFIGURATION OSD VIA FC
Step 5: Disconnect and close cleanflight but leave all the connections as they are.
Step 6: Open up your software you use to configure it. In my case it was MwOSD GUI.
Step 7: Select the port you noted in Betaflight being used to connect to your flight controller and
connect.
Step 8: You should have read/write access now to the device.
Step 9: When you’re done all you need to do is reset the flight controller via reset button or unplugging
USB and battery. This will remove the serialpassthrough so you can once again access it via Betaflight.