FURNA E1 User manual

E1
Electric Standing Desk
A BETTER DESK FOR A BETTER YOU
ASSEMBLEY GUIDE
MODEL - FNAE1FRMGRY1

Part A
Qty 1
Part B
Qty 1
Part C
Qty 2
Part E
Qty 2
Part J
Qty 1
Part G
Qty 1
Part H
Qty 1
Part K
Qty 2
Part M
Qty 1
(Pre-attached to frame)
Part N
Qty 1
Part 16 | Qty 12
M4X20
Part 19 | Qty 4
M8X10
Part 20 | Qty 6
M4X6
Part 21 | Qty 8
M6X10
Part 22 | Qty 2
M6
Part 23 | Qty 4
Part 17 | Qty 8
M6X16
Part 18 | Qty 18
M6X15
Part L
Qty 1
Part F
Qty 2
Part D
Qty 2
Parts List

1Installation of legs
and feet
Parts used: A, B, C plus:
Part No.24
Qty x 3
Part No.17
Qty x 8
Note: There is a welded
bracket with two screw
holes on the back of each
leg. Make sure they both
face the REAR of the
desk (they should face
away from the “long” part
of the feet).
Erection Sequence: 1,2,3,4
1
2
3
4
1
2
3
4

2
3
Frame assembly
Part One
Frame assembly
Part Two
Slide Parts K inside each Part
D of the frame as shown in the
picture.
Note: Parts K may already be
sitting inside Parts D when you
open the packaging.
Make sure Parts K are centred,
and then loosely screw in Part 21
bolts (M6 X 10MM) to hold Parts
K in place.
Connect both Parts D to the
desk legs Parts A & B as shown
in picture.
Use Parts 18 (M6 X 15MM bolts)
and loosely tighten in place.
Parts used: A,B,D plus
Parts used: A,B,D K plus
Part No.21
Qtyx8
Part No.18
Qtyx8
1
1
3
3
2
2
2
2
1
1
1
1
2
2
Erection Sequence: 1,2
Erection Sequence: 1,2, 3

4Axle assembly
Slide one Part E bar into the B leg axle hole (through
the motor which is pre-attached) and then insert Part
G on to that same Part E. Once this is done, slide the
remaining available Part E bar from the outer side of
Leg A as shown in the picture so that it also sits inside
Part G.
Insert small black screws (Parts 20) along the available
holes in Part G so as to hold the Parts E & G together
securely.
Note: Do not fully tighten until you have set your
preferred frame width (based on the side of your
chosen desk top).
Parts used:
E,G plus
Part No.20
Qtyx4
Erection Sequence: 1,2,3,4
1
4
3
2

5Desk top supports
assembly
Attach both Parts F (desk top supports) to each end of the desk
frame using Part 18 bolts and then tighten.
Part No.18
Qtyx8
Erection Sequence: 1,2,3
1
1
3
2
2
Part used: F plus

Turn the desk top upside down and lay at on the oor, and
put the frame on upside down on top of it for this part. Set
the frame to the width that suits you and the table top (we
recommend within about 5cm from each side). Once this is
set, make sure you go back and tighten all bolts (On Parts A,
B, G, F). Once everything is tightened, use a drill or electric
screwdriver and attach desk top to the frame using 6 x Part
16 tapping screws.
Note: Be sure to tighten bolts from all previous steps
BEFORE attaching the table top.
Parts used
A,B,F plus
6Desk top attachment
Part No.16
Qtyx8

7Install control box
& control panel
Parts used
L, J N plus Part 16
Part J
Qty 1
Part N
Qty 1
Part L
Qty 1
L
J
N
Using the diagram as a guide, you may now connect the motor to the control box (Part J), and
the control panel (Part L). The exact position of the control box and control panel are at your
discretion. Once you have selected these positions, you can screw them in place using the
remaining Parts 16 (tapping screws).
Note: Do not attach the power cord to a power outlet until all positioning and drilling has been
completed and the desk is in the upright position once again.
Part No.16
Qtyx4

8Optional: Support bar/
modesty panel
Part No.18
Qtyx2
Part No.19
Qtyx4
Part No.22
Qtyx2
This is an optional attachment for increased stability.
Firstly attach the support bar (Part H) to the legs using 4 x Part 19 bolts. Once the bar is
attached, use Parts 19 and 22 and screw tightly to hold in the middle cutout section.
Part H
Qtyx1
Part 22

9Leg height calibration
After plugging desk in to a power source, press and hold the down button until
the desk reaches the minimum height. When you hear a “beep” sound this has
been achieved and leg calibration complete.
Height memory settings
Press and hold the M button for 3 seconds, and then adjust the desk height
to the required level. Once the height is reached and while the LED panel is
ashing, simply press one of the number buttons (1, 2, 3 or 4) and that button
will then automatically adjust the desk to the set height.
Congratulations, you’re ready to use your Furna E1 desk!

Need help?
Get in touch by emailing [e-mail] or
by using our Live Chat feature on our website!