FURNA E1 User manual

E1
Electric Standing Desk
ASSEMBLY GUIDE
MODEL FNAE1FRMXXX3

Leg 2
Qty 1
Leg 1
Qty 1
Foot
Qty 2
Main axle
Qty 2
Control Box
Qty 1
Main axle connector
Qty 1
Leg support bar
Qty 1
Shoulder connector
Qty 2
Electric Motor
Qty 1
(Pre-attached to frame)
AC Cable
Qty 1
Control Panel
Qty 1
Top Support Bar
Qty 2
Frame shoulder support
Qty 2
Parts List
Part E
M5*6
Quantity=6PCS
Select allen key based on parts
being used.
Extra parts are sometimes included and can be kept as spares.
Part D
M6
Quantity=2PCS
Foot stability pad
Qty 4
Note: Foot stability pads may
already be connected to feet.
Part C
M8*10
Quantity=4PCS
Part B
M6*10
Quantity=8PCS
Part F
M4*20
Quantity=12PCS
Part A
M6*16
Quantity=26PCS

1Installation of legs
and feet
Parts used:
Foot stability pad
Qty x 4
A
Qty x 8
Note: There is a welded
bracket with two screw
holes on the back of each
leg. Make sure they both
face the REAR of the
desk (they should face
away from the “long” part
of the feet).
Erection Sequence: 1,2,3,4
1
2
3
4
1
2
3
4

2
3
Frame assembly
Part One
Frame assembly
Part Two
Slide the shoulder connectors
inside each of the frame shoulder
supports on the frame as shown
in the picture.
Note: The shoulder connector
may already be sitting inside the
shoulder support when you open
the packaging.
Make sure the shoulder
connectors are centred, and then
loosely screw in B bolts (M6 X
10MM) to hold the connectors in
place.
Connect both frame shoulder
supports to the desk legs Parts 1
& 2 as shown in picture.
Use Part A (M6 X 15MM bolts)
and loosely tighten in place.
Parts used:
Parts used:
Leg 1
Leg 2
Frame Shoulder Supports
Shoulder Connectors
Part B
Qtyx8
A
Qtyx8
1
1
3
3
2
2
2
2
1
1
1
1
2
2
Erection Sequence: 1,2
Erection Sequence: 1,2, 3

4Axle assembly
Change to: Slide the two main axle bars part way
into each end of the main axle connector tube. Then,
position the full (3 parts) axle between the two legs
and thread the axles through the gear mechanism in
each leg. The right hand side will also pass through the
motor.
Screw in Parts E (small black slug screws) using the
smallest allen key once the axle bars have linked each
leg mechanism.
Note: Do not fully tighten until you have set your
preferred frame width (based on the size of your
chosen desk top).
Parts used:
E
Qtyx4
Erection Sequence: 1,2,3,4
1
4
3
2

5Desk top supports
assembly
Attach both Top support Bars (desk top supports) to each end
of the desk frame using Part A bolts and then tighten.
A
Qtyx8
Erection Sequence: 1,2,3
1
1
3
2
2
Part used: Top support bars

Turn the desk top upside down and lay at on the oor, and
put the frame on upside down on top of it for this part. Set
the frame to the width that suits you and the table top (we
recommend within about 5cm from each side). Once this
is set, make sure you go back and tighten all bolts. Once
everything is tightened, use a drill or electric screwdriver and
attach desk top to the frame using 6 x Part F tapping screws.
Note: Be sure to tighten bolts from all previous steps
BEFORE attaching the table top.
Parts used:
6Desk top attachment
F
Qtyx6

7Install control box
& control panel
Parts used:
Control Box
Qty 1
AC Cable
Qty 1
Control Panel
Qty 1
Using the diagram as a guide, you may now connect the motor to the control box, and the control
panel. The exact position of the control box and control panel are at your discretion. Once you
have selected these positions, you can screw them in place using the remaining Parts F (tapping
screws).
Note: Do not attach the power cord to a power outlet until all positioning and drilling has been
completed and the desk is in the upright position once again.
F
Qtyx6

8Optional: Support bar/
modesty panel
A
Qtyx2
C
Qtyx4
D
Qtyx2
This is an optional attachment for increased stability.
Firstly attach the support bar to the legs using 4 x C bolts. Once the bar is attached, use Parts C
and D and screw tightly to hold in the middle cutout section.
Leg Support Bar
Qtyx1
Part D

9Leg height calibration
After plugging desk in to a power source, press and hold the down button until
the desk reaches the minimum height. When you hear a “beep” sound this has
been achieved and leg calibration complete.
Height memory settings
Press and hold the M button for 3 seconds, and then adjust the desk height
to the required level. Once the height is reached and while the LED panel is
ashing, simply press one of the number buttons (1, 2, 3 or 4) and that button
will then automatically adjust the desk to the set height.
Congratulations, you’re ready to use your Furna E1 desk!

Need help?
Get in touch by emailing [e-mail] or
by using our Live Chat feature on our website!