Fusion ENCOUNTER EN-AB1120 User manual

ENCOUNTER
ACTIVE ENCLOSURES
EN-AB1120, EN-AB2120
Product Specifications
Control Descriptions
LEVEL
This allows the adjustment of the amplifier level of the subwoofer. Turn clockwise to increase the level. If
the sound becomes distorted reduce the level.
LOW PASS FILTER (LPF)
This allows the adjustment of the highest frequency the Encounter Active Enclosure Tube will produce.
This should be adjusted to blend with your main speakers. Typically, this will be set to around 100Hz (ap-
proximately the central position of the control knob).
BASS
This allows very low frequencies to be boosted. Adjust with care and listen for distortion. If the sound be-
comes distorted, reduce the amount of boost.
REMOTE LEVEL CONTROLLER
When connected, this allows further control over the level from a remote location, using the supplied lead.
Installation
Make sure the Encounter Active Enclosure is firmly fixed in your vehicle. Check before drilling or cutting
holes. DO NOT work near gas tanks, fuel lines, hydraulic lines or electrical wiring.
DO NOT mount the Encounter Active Enclosure in such a way as to pinch or damage the wires.
Make sure everything is firmly connected, before attaching the +12V wire. Make sure the +12V wire is
fused as close as possible to the battery. ALWAYS use a fuse with the recommended rating.
EN-AB1120 EN-AB2120
Max Power Rating 360 Watts 550 Watts
Frequency Repsonse 4OHz - 500Hz 35Hz - 500Hz
Bass Boost (Variable) 0 / + 18dB 0 / + 18dB
Low Pass Filter (Variable)40Hz - 250Hz 40Hz - 250Hz
Tuning Bass Reflex Bass Reflex
Woofer Size 12” 2 x 12”
Fuse 15 Amp
Box Dimensions 520mm x 375mm x 405mm
20 1/2” x 14 3/4” x 15 15/16”
880mm x 375mm x 415mm
34 10/16” x 14 3/4” x 16 3/8”

RECORD YOUR PURCHASE DETAILS HERE:
MODEL NUMBER __________________________ DATE OF PURCHASE__________________________
AFFIX RECEIPT HERE
For further product and installation information please visit www.fusionelectronics.com
Para obtener más información sobre los productos o su instalación, visite www.fusionelectronics.com
Weitere Informationen zum Produkt und zur Installation finden Sie auf folgender Website: www.fusionelectronics.com
Ga naar www.fusionelectronics.com voor meer product- en montage-informatie
Pour plus de renseignements sur les produits et l’installation, veuillez consulter www.fusionelectronics.com
Per ulteriori informazioni su prodotto e installazione, potete visitare www.fusionelectronics.com
За дополнительной информацией о продукции и установке обращайтесь на www.fusionelectronics.com www.fusionelectronics.com
Specifications and design are subject to change without notification
WARNING! Audio Systems can produce sound levels over 135dB. Continuous exposure to sound pressure levels over 100dB may
cause permanent hearing loss! Please watch for emergency vehicles as warning signals may not be heard. USE COMMON SENSE!
Wiring
• Connect the ground wire to the vehicle first (clean dirt and paint to bare metal).
• Connect the 12 volt (red wire) to the positive battery terminal. Make sure the fuse is
close to the battery.
• Connect the remote on (blue wire)
• Connect the RCA cables if applicable, OR
• Connect the speaker level wire by splicing into the headunits speaker wires.
See Note 1
• Connect the remote level controller with the supplied lead.
• Check all connections.
• Finally, connect the power plug end of the power harness to the unit.
FUSE
L -
L+
MIN MAX 250Hz40Hz 18dB0dB
R -
LOW INPUT
Right
REMOTE
R+
INPUT
HIGH
Left
POWER
PROT
L.P.F BASS POWER
REM
+12 GND
EN-AT110
LEVEL
Connect black
wire to chassis
ground of vehicle
(Ground)
Connect red wire to
positive (+12V) battery
terminal
Connect blue wire to
source unit’s accessory
lead or switched 12 volt
source (REM)
See note 1
Splice into source
unit’s speaker wires
(R+) Grey/White
(R- ) Grey
(L+) Green/White
(L- ) Green
Vehicle Battery
Positive
Remote Level Controller
*Note 1 Take care to make
sure the wires are spliced in
the correct phase. Positive to
positive, negative to negative.
Failure to do this correctly could
result in loss of bass.
Power Plug
Speaker Level
Input Plug
Connect the remote
level controller lead to
the amplified tube