Gaggenau CM470111 User manual

Instruction manual
CM 470
Fully Automatic Espresso Machine

2
en
Table of contents
Instruction manual
Intended use 3
( Important safety information 3
7 Environmental protection 4
Saving energy 4
Environmentally-friendly disposal 4
Familiarising yourself with your appliance 5
Included in delivery 5
Assembly and components 6
Display and operating controls 7
Function selector positions 7
Symbols 7
Colours and display 8
Automatic door opening 8
Additional information (and )8
Accessories 9
Switching the appliance on and off 9
Main switch 9
Hibernate mode 10
Activating the appliance 10
Setting up the appliance 10
Initial settings 10
Setting the water hardness 11
Water filter 11
Operation with or without a water filter 11
Inserting the water filter 12
Fill bean container 12
Preparing beverages 13
Beverage selection 13
Preparing coffee using freshly ground beans 14
Preparing two cups at the same time 14
Preparing coffee using ground coffee 15
Preparing a coffee with milk 15
Preparing milk froth and warm milk 16
Preparing hot water 16
Setting the grinding level 17
Changing bean type 17
Individual beverages 17
Child lock 18
Activating the child lock 18
Deactivating the child lock 18
Basic settings 19
Setting the milk container weight 21
Messages 21
Daily care and cleaning 22
Daily maintenance 22
Cleaning the milk system 23
Cleaning the brewing unit 24
Service programmes 25
Cleaning 25
Descaling 26
Cleaning and descaling 26
Fill the water tank with fresh water. 27
Emptying programme 27
Simple troubleshooting 28
Technical data 30
AQUA-STOP guarantee 30
Additional information on products, accessories,
replacement parts and services can be found at
www.gaggenau.com and in the online shop
www.gaggenau.com/zz/store

3
Intended use en
Intended use
Intendeduse Check the appliance for damage after
unpacking it. Do not connect the appliance if it
has been damaged in transport.
This appliance is intended for domestic use
only.
Only use the appliance indoors at room
temperature and up to 2000 m above sea level.
Protect the appliance from frost, otherwise it
will become damaged.
m ( Important safety
information
Important safety informati on Please read carefully, follow and retain the
operating instructions. When passing on the
appliance, enclose these instructions.
This appliance can be used by children aged
from 8years and above and by persons with
reduced physical, sensory or mental
capabilities or lack of experience and
knowledge if they have been given supervision
or instruction concerning use of the appliance
in a safe way and if they understand the
hazards involved. Keep children under 8years
of age away from the appliance and connecting
cable and do not allow them to use the
appliance. Children shall not play with the
appliance. Cleaning and user maintenance
shall not be made by children unless they are
older than 8years and supervised.
mWarning – Danger of electric shock!
▯The appliance may only be connected to a
power supply with alternating current via a
correctly installed socket with earthing.
Ensure that the protective conductor
system of the domestic electricity supply
has been correctly installed.
Risk of electric shock!
▯Connect and operate the appliance only in
accordance with the specifications on the
rating plate. If the power cord of this
appliance is damaged, it must be replaced
by customer service.
Risk of electric shock!
▯Do not use if the power cable or appliance
is damaged. If a fault occurs, pull the mains
plug or switch off the mains voltage
immediately.
Risk of electric shock!
▯If water is leaking from the inlet hose, turn
off the tap at once. When connecting or
working on the water pipe, disconnect the
appliance from the mains power supply.
Risk of electric shock!
▯To prevent hazards, the appliance may be
repaired by our customer service only.

4
en Environmental protection
Risk of electric shock!
▯Never immerse the appliance or mains cord
in water.
Risk of electric shock!
▯The plug and socket connection of the
appliance must not come into contact with
liquids.
mWarning – Hazard due to magnetism!
The appliance contains permanent magnets
which may affect electronic implants, e.g. heart
pacemakers or insulin pumps. Persons wearing
electronic implants must maintain a minimum
distance of 10 cm from the appliance and from
the following parts upon removal: milk
container, milk system, water tank and brewing
unit.
mWarning – Risk of suffocation!
Do not let children play with packaging
material. Store small parts safely as they can be
easily swallowed.
mWarning – Risk of burns!
▯The milk system becomes very hot. After
use, allow it to cool down first before
touching it.
Risk of burns!
▯Some parts of the appliance become very
hot. Never touch hot appliance parts.
mWarning – Risk of injury!
▯Improper use of this appliance may result in
injury.
Risk of injury!
▯Do not reach into the grinding unit.
Risk of injury!
▯Be careful not to jam your fingers when
closing the door.
mWarning – Risk of fire!
The appliance will become hot. Ventilate the
appliance adequately.Never operate the
appliance in a unit with the cabinet door
closed.
mWarning – Risk of harm to health!
Soiling on the appliance may be dangerous to
health. Follow the cleaning instructions for the
appliance.
7 Environmental protection
Environmentalprotection Saving energy
▯If the appliance is not being used, switch it off.
▯Set the interval for automatic switch-off to the
smallest value.
▯If possible, do not interrupt coffee or milk froth
dispensing. Stopping a process prematurely results
in higher energy consumption and the drip tray fills
up more quickly.
▯Descale the appliance regularly to avoid a build-up
of limescale. Limescale residue results in higher
energy consumption.
Environmentally-friendly disposal
Dispose of packaging in an environmentally-friendly
manner.
Please ask your dealer about current disposal routes.
This appliance is labelled in accordance with
European Directive 2012/19/EU concerning
used electrical and electronic appliances
(waste electrical and electronic equipment -
WEEE). The guideline determines the
framework for the return and recycling of used
appliances as applicable throughout the EU.

5
Familiarising yourself with your appliance en
Familiarising yourself with your
appliance
Familiari singyourself withyour appliance Use this section to familiarise yourself with your new
appliance. The control panel and the individual
operating controls are explained. You will also be
informed about the accessories.
Further information about the appliance, such as how to
change the opening angle of the door, can be found in
the enclosed installation instructions.
Included in delivery
(For use)

6
en Familiarising yourself with your appliance
Assembly and components







 



 




7
Familiarising yourself with your appliance en
Display and operating controls
--------
Function selector positions
Symbols
The following overview details the symbols that are the
most used when operating the appliance.
--------
1 Display and controls
2 Shelf, e.g. for a cup
3 Water tank with cover
4 Accessory drawer (for quick reference guide and
accessories)
5 Bean container
6 Grinding level adjustment
7 Magnetic holder (for milk hose connecting element)
8 Ground coffee drawer
9 Protective cover (for brewing unit)
10 Collecting tray
11 Rating plate
12 Holder (for milk tube)
13 Drip tray
14 Drain filter
15 Coffee residue container
16 Beverage dispenser and milk system, height-adjusta-
ble
17 Milk container
18 Shelf (scales) for milk container, removable
1 Control panel These areas are touch sensitive.
Touch a symbol to select the cor-
responding function.
2 Display The display shows, for example,
current settings and options.
3 Rotary selector You can select the desired bever-
age and other settings using the
rotary selector.
4 Function selector You can use the function selector
to call up beverages or the favour-
ite drinks you have saved.



(VSUHVVR
[
[
Position Function
0 Zero setting
@Light
2 Beverage selection
3- 10 Memory locations for individual beverages
S Service programmes/basic settings
Symbol Function
IStart
ØStop
'Cancel
™Confirm/save settings
CSelection arrow
!Opening the door
(Call up additional information
*Call up additional tips
%Edit settings
‡Save individual beverage
Quick capacity selection
2x 2beverages
0Child lock










8
en Familiarising yourself with your appliance
Colours and display
Colours
The different colours are used to guide the user in the
relevant setting situations.
Appearance
The symbols, values and displays may change,
depending on the situation.
Automatic door opening
The appliance door springs open when you touch the !
symbol and you can open it fully by using the recessed
handle on the side.
Automatic door opening does not work if the child lock
is activated or there is a power cut. You can open the
recessed handle on the side by hand.
Additional information (and )
By touching the (symbol you can call up additional
information.
During operation you will for example receive
information about the number of beverages dispensed
previously.
If the function selector is set to S, you will for example
receive information about when the appliance needs to
be descaled or cleaned, or when the water filter needs
changing. You can use this information for example to
start a service programme that is due soon.
The )symbol appears for important user prompts. New
messages are also shown on the display for several
seconds. These messages disappear automatically after
a few seconds or must be confirmed with ™. A list of
messages can be displayed by touching the ) symbol.
The message disappears when the required action has
been carried out.
Orange Initial settings
Main functions, messages
Blue Basic settings
Cleaning
White Adjustable values
Standard Values and symbols which have just
been selected will be displayed in a
larger font.
Reduced dis-
play screen
After a short while, the amount of infor-
mation shown on the display will be
reduced and only the most important
information will remain. This function is
activated in the basic settings ex works
and can be deactivated.

9
Switching the appliance on and off en
Accessories
The fully automatic espresso machine has a drawer for
storing accessories such as the quick reference guide
or measuring spoon inside the appliance. After opening
the door, you can use the magnetic holder and the clip
for the individual parts, such as the milk hose set. The
holder for the milk tube is situated on the inside of the
door.
The appliance includes the following accessories as
standard:
The following accessories can be ordered by contacting
the after-sales service:
▯Water filter (order no.: 17000705)
▯Cleaning tablets (order no.: 00311769)
▯Descaling tablets (order no.: 00311819)
▯Stainless-steel milk container
(order no.: 11019259)
▯Limit stop for 92° opening angle
(order no.: 00636455)
▯Bean container with lid
(order no.: 11015223)
▯Water inlet hose extension
(order no.: 11019575)
Switching the appliance on and off
Switchingtheapplianceonandoff Main switch
The main switch is used to switch the appliance on and
off.
If the appliance is switched off at the main switch, the
power supply is interrupted.
The appliance is programmed so that it switches to
standby mode automatically after about 30 minutes. This
timespan can be changed. ~"Basic settings"
on page 19
The appliance rinses automatically when it is switched
on at the main switch. Exception: The appliance was
only switched off a few minutes beforehand.
Notes
– Do not press the main switch during operation. If
you want to manually switch off the appliance, you
must first set the function selector to 0so that it
rinses automatically. Then switch off the appliance
using the main switch.
– The appliance is equipped with a sensor. If a milk
container is present, this will be shown on the
display when switching to energy-saving mode
(function selector set to 0). If there is milk in the
container, please keep in the refrigerator.
Measuring spoon
For adding ground coffee.
Milk hose set
For connecting the milk container.
Milk tube
For inserting into the milk container,
milk cartons and milk bottles or for
running a service programme.
Milk container
Volume capacity 0.5litres.
The milk container has been
designed especially for use together
with this fully automatic coffee
machine. It is intended solely for use
in the household and for storing milk
in the refrigerator.

10
en Setting up the appliance
Hibernate mode
The appliance goes into hibernate mode if the function
selector is turned to 0or if the child lock is activated.
The brightness of the display is dimmed in hibernate
mode during the first few minutes.
The display then switches itself off.
Notes
– In Basic settings, you can select whether the
Gaggenau logo is to be displayed during hibernate
mode. ~"Basic settings" on page 19
– The brightness of the display depends on the
vertical viewing angle. You can adjust the display
using the "Brightness" setting in the basic settings.
Activating the appliance
To leave hibernate mode or to activate the display when
it has been switched off, turn the function selector.
You can now set the desired function. You can read
about how to set functions in the respective chapters.
Note: If no drip tray is inserted, the appliance cannot be
switched on and no water will flow from the coffee
dispenser.
The message "Insert trays" appears.
Setting up the appliance
Settinguptheappliance Note: Only use the appliance in frost-free areas. If the
appliance was transported or stored at temperatures
below 0°C, you must wait for at least 3hours before
using it.
Before the appliance can be switched on and used, it
must be assembled and connected according to the
enclosed installation instructions.
Initial settings
Notes
– The query appears automatically when first
switched on after connection to a power outlet.
– You can change the settings at any time. ~"Basic
settings" on page 19
1Switch on the appliance at the main switch.
The preset language appears in the display.
2Turn the rotary selector to select the required
display language.
3Press ™to confirm.
The temperature unit appears in the display.
4Use the rotary selector to select the required
temperature unit.
5Press ™to confirm.
The preset capacity unit appears in the display.
6Use the rotary selector to select the required
capacity unit.
7Press ™to confirm.
The preset weight unit appears in the display.
8Use the rotary selector to select the required
weight unit.
9Press ™to confirm.
The display shows "Initial set-up complete".. Confirm
with ™. The appliance is now ready to use.
Note: If the language is changed, the system restarts.
This takes a few seconds.
'HXWVFK
6SUDFKH

11
Water filter en
Setting the water hardness
It is important to set the water hardness correctly so
that the appliance indicates in good time when the
descaling programme should be run. The preset water
hardness is level 4. If a water softening unit is installed
in the household, select the "Softening device" setting.
You can check the water hardness using the enclosed
test strip or by asking your local water supplier.
1Briefly immerse the enclosed test strip in fresh tap
water, leave it to drip and read off the result after
one minute.
2Rotate the function selector to S.
3Use the rotary selector to select "Basic settings"
and touch the ™symbol.
4Use the rotary selector to select "Water hardness".
5Touch the %symbol.
6Using the rotary selector, set the measured water
hardness.
7Press ™to confirm.
The setting has been saved. Touch 'to exit the basic
settings.
Water filter
Waterfilter Operation with or without a water
filter
You can use the appliance with or without a water filter.
To ensure that the descaling display of the appliance
functions correctly, you must specify in the basic
settings whether a water filter is used.
1Rotate the function selector to S.
2Select "Basic settings" using the rotary selector.
3Touch the ™symbol.
4Select "Water filter" using the rotary selector.
5Touch the %symbol.
6Use the rotary selector to select either "Available"
(with water filter) or "Not available" (without water
filter).
7Press ™to confirm.
The rinse program starts with the "Available"
setting. Proceed according to the information on
the display.
8Touch the 'symbol to leave the Basic settings
menu.

12
en Fill bean container
Inserting the water filter
New water filters must always be rinsed after being
fitted.
1Rotate function selector to S.
2Select "Water filter change" using the rotary
selector.
3Touch the ™ symbol.
4Insert the water filter in the water tank.
5Remove the milk hose from the milk container and
close the door.
6Touch the ™ symbol.
Water will only now run through the filter to rinse it.
After the rinsing process, confirm with ™ . The
appliance is ready for use again.
Rinsing the filter also activates the setting for the
display "Change water filter".When the display "Please
change water filter" is shown or at the latest after two
months, the filter is no longer effective. It needs to be
replaced for reasons of hygiene and so that the
appliance does not experience a build-up of limescale
(which could damage the appliance).
Replacement filters can be obtained from the after-sales
service. ~"Accessories" on page 9
Note: If the appliance has not been used for a long
period of time (due to holidays, for example), the filter
that is fitted should be rinsed before using the
appliance. To do this, simply dispense a cup of hot
water.
Fill bean container
Fill beancontainer Using your appliance, you can prepare coffee using
freshly ground coffee beans or ground coffee. Always
only add ground coffee shortly before making a drink.
~"Preparing coffee using ground coffee" on page 15
1Open the door.
2Pull the bean container out, remove the lid and fill
the container with beans. Replace the lid and insert
the bean container again.
Note: Coffee beans that have been glazed or
caramelised or that contain other sugary additives
block the brewing unit. Only use pure bean mixes
that are suitable for use in fully automatic espresso
or coffee machines.
3Close the door.

13
Preparing beverages en
Preparing beverages
Prepari ngbeverages Beverage selection
Notes
– The integrated fan switches on each time a drink is
dispensed and switches off again after a few
minutes.
– When first using the appliance or when it has not
been used for a long time, the first cup of coffee
does not have the full aroma.
– The appliance is programmed with the standard
factory settings for optimal performance.
– After starting the appliance for the first time, you
will only consistently achieve a suitably thick and
stable crema after the first few cups have been
dispensed.
--------
You may be able to select further options depending on
your choice of beverage:
--------
Aroma function "Extra strong"
The longer coffee is brewed, the more bitter substances
and undesired aromas are released. This has a negative
effect on the taste and makes the coffee less easily
digestible. Your appliance therefore has a special
Aroma function for very strong coffee. After half the
requested volume has been prepared, coffee is ground
and brewed once more, so that only the palatable and
easily digestible flavours are released.
The Aroma function "Extra strong", e.g. "Extra
strong 3ˆ2x" is only available for certain settings. The
coffee is prepared in two stages with this setting. Wait
until the process is fully completed.
„Ristretto Concentrated espresso. Best
served in small, thick-walled cups.
Preheat cups with hot water.
„Espresso Concentrated coffee. Serve in
small, thick-walled cups. Preheat
cups with hot water.
…Coffee Coffee
Americano Yespresso, is topped up with
Zhot water.
sHot water For preparing hot drinks, e.g. tea,
or to preheat cups.
tMilk froth For preparing speciality white cof-
fees.
uWarm milk As a beverage or as an ingredient
in special coffee beverages.
wWhite coffee ½ coffee + ½ milk; best served in
a wide-rimmed cup.
†Latte Macchiato A specialty drink, served in a glass
featuring three layers: at the bot-
tom hot milk, in the middle
espresso, and at the top milk froth.
Flat White Espresso with frothed milk.
Cappuccino Yespresso + Ymilk + Y milk
froth; best served in a cup.
vEspresso Mac-
chiato
Espresso finished with milk froth.
´
´
¦Size Small - Medium - Large - Very large
ˆStrength Very mild - Mild - Medium - Strong -
Very strong - Extra strong etc., not
available for milk froth, warm milk
and hot water
pTemperature Hot - Very hot - Extra hot not availa-
ble for milk froth and warm milk
Different temperatures can be
selected for hot water.
Mixing ratio Setting for the proportion of milk,
only available for coffee beverages
with milk.

14
en Preparing beverages
Preparing coffee using freshly ground
beans
The appliance must be switched on. The bean container
must be filled.
1Rotate function selector to position 2.
2Use the rotary selector to select the desired
beverage, e.g. coffee.
3Place a cup under the coffee dispenser.
4Touch the Csymbol.
5Set the size using the rotary selector.
6Touch the Csymbol.
7Set the strength using the rotary selector.
8Touch the Csymbol.
9Set the temperature using the rotary selector.
10 Press ™to confirm the settings.
11 Press Ito start.
The beverage is brewed and then runs into the cup.
Notes
– While the beverage is dispensed, the &symbol is
displayed. Touch this symbol to stop the beverage
being prepared.
– Using the ‡symbol, you can save the current
beverage: Touch the ‡symbol, turn the function
selector to a free memory location and save the
entry. ~"Individual beverages" on page 17
Preparing two cups at the same time
You have the option of dispensing two beverages
simultaneously:
1Select the beverage and use the rotary selector to
choose settings such as the temperature if desired.
2Touch the 2xsymbol.
3Place two cups, or similar, underneath the beverage
dispenser.
4Press Ito start.
The beverage selected is brewed and then dispensed
into the cups.
Note: The coffee is prepared in two stages. Wait until
the process is fully completed.
&RIIHH
[
[
0HGLXP
0LOG
+RW

15
Preparing beverages en
Preparing coffee using ground coffee
The appliance must be switched on.
Important: Remove cups or glasses before opening the
door as they may otherwise fall off.
1Turn the function selector to position 2.
2Open the door.
3Using the measuring spoon, fill a maximum of two
level spoonfuls of ground coffee into the ground
coffee drawer. Close the ground coffee drawer.
Note: Do not fill the drawer with beans or instant
coffee.
4Close the door.
5Use the rotary selector to select the desired
beverage (beverages made from ground coffee are
identified with the xsymbol).
6Place a cup under the coffee dispenser.
7Touch the Csymbol.
8Set the quantity using the rotary selector.
9Touch the Csymbol.
10 Set the temperature using the rotary selector.
11 Confirm the settings using ™.
12 Press Ito start.
The beverage is brewed and then runs into the cup. To
prepare another cup, refill with ground coffee and
repeat the process.
Notes
– While the beverage is dispensed, the &symbol is
displayed. Touch this symbol to stop the beverage
being prepared.
– If coffee is not dispensed within 90seconds, the
brewing chamber empties itself automatically to
prevent an overflow.
– The Aroma function is unavailable when using
ground coffee. Similarly, it is not possible to
dispense two cups at once when using ground
coffee.
Preparing a coffee with milk
mWarning – Risk of burns!
The milk system becomes very hot. After use, allow it to
cool down first before touching it.
You can decant the milk into the milk container supplied
or fill e.g. into a milk jug or use the milk directly from the
carton. ~"Setting the milk container weight"
on page 21
Important: Remove cups or glasses before opening the
door as they may otherwise fall off.
Using the milk container:
▯Open the door.
▯Push the beverage dispenser down completely.
▯Remove the cover of the beverage dispenser
towards the front.
▯Attach a milk hose from the milk system to the
beverage dispenser and feed it outwards through
the opening at the top.
▯Attach the connecting element of the milk system to
the magnetic holder (on the inside of the
appliance).
▯Place the filled milk container on the right next to
the coffee dispenser. Connect the milk tube to the
milk hose and then guide the milk tube into the milk
container. The end of the milk tube must be
immersed in the milk.
▯Close the door.
Using a milk carton or other container:
▯Open the door.
▯Push the beverage dispenser down completely.
▯Remove the cover of the beverage dispenser
towards the front.
▯Feed the milk hose of the milk system outwards
through the opening at the top.
▯Attach the magnetic holder to the appliance.
▯Place the filled milk carton on the right next to the
coffee dispenser. Connect the milk tube to the milk
hose and then guide the milk tube into the milk
carton. The end of the milk tube must be immersed
in the milk.
▯Close the door.

16
en Preparing beverages
To prepare a drink:
The appliance must be switched on. The bean container
must be filled.
1Rotate function selector to position 2.
2Using the rotary selector, select a coffee beverage
with milk. To select a beverage made with ground
coffee, you must first fill the ground coffee drawer.
3Place a cup or glass under the coffee dispenser.
4Press Ito start.
- or -
Touch the Csymbol first, then set the size or
strength for example, using the rotary selector.
Confirm with ™.
The milk is drawn in and prepared and then the coffee is
brewed.
Notes
– While the beverage is dispensed, the &symbol is
displayed. Touch this symbol to stop the beverage
being prepared.
– Using the ‡symbol, you can save the current
beverage: Touch the ‡symbol, turn the function
selector to a free memory location and save the
entry. ~"Individual beverages" on page 17
– Dried-on milk residues are difficult to remove, so
always clean the milk system after every use.
~"Cleaning the milk system" on page 23
Preparing milk froth and warm milk
mWarning – Risk of burns!
The milk system becomes very hot. After use, allow it to
cool down first before touching it.
To prepare a drink:
The appliance must be switched on.
1Rotate the function selector to position 2.
2Connect the milk hose. ~"Preparing a coffee with
milk" on page 15
3Select "Milk froth" or "Warm milk" with the rotary
selector.
4Place a cup or glass under the coffee dispenser.
5Touch the Csymbol.
6Set the size using the rotary selector.
7Press ™to confirm the settings.
8Press Ito start.
The milk is drawn in and then flows into the cup or
glass.
Notes
– While the beverage is dispensed, the &symbol is
displayed. Touch this symbol to stop the beverage
being prepared.
– Using the ‡symbol, you can save the current
beverage: Touch the ‡symbol, turn the function
selector to a free memory location and save the
entry. ~"Individual beverages" on page 17
– Dried-on milk residues are difficult to remove, so
always clean the milk system after every use.
~"Cleaning the milk system" on page 23
Preparing hot water
mWarning – Risk of burns!
The milk system becomes very hot. After use, allow it to
cool down first before touching it.
The appliance must be switched on.
1Remove the milk tube from the milk container.
2Rotate function selector to position 2.
3Select "Hot water" using the rotary selector.
4Place a cup or glass under the coffee dispenser.
5Touch the Csymbol.
6Set the size using the rotary selector.
7Touch the Csymbol.
8Set the temperature using the rotary selector.
9Confirm with ™.
10 Press Ito start.
The water is heated and then flows into the cup or glass.
Notes
– While the beverage is dispensed, the &symbol is
displayed. Touch this symbol to stop the beverage
being prepared.
– Using the ‡symbol, you can save the current
beverage: Touch the ‡symbol, turn the function
selector to a free memory location and save the
entry. ~"Individual beverages" on page 17

17
Individual beverages en
Setting the grinding level
mWarning – Risk of injury!
Do not reach into the grinding unit.
Using the slider for the grinding level, the desired
fineness of the ground coffee can be set between a fine
grinding level (left) and a coarser grinding level (right).
Notes
– The new setting only becomes noticeable after the
second cup of coffee.
– Set a finer grinding level with dark-roasted beans
and a coarser grinding level with lighter beans.
– If the display shows the message "Set coarser
grinding level", the coffee beans are being ground
too finely. Set a coarser grinding level. To do so,
slide the slider to the right.
– Only make small changes to the grinding level
setting.
Changing bean type
If you are using a new type of bean, the Empty grind
function allows you to run the grinding unit until empty
of your previous bean type.
The appliance must be switched on.
1Remove the bean container and empty out the
beans.
2Add the new beans and reinsert the bean container.
The message "New type of coffee beans in bean
container?" appears.
3Press ™to confirm.
The grinding unit is then emptied of your previous bean
type in two grinding stages.
Note: This message always appears when the bean
container is inserted. If you do not want to empty the
grinding unit, e.g. when only refilling with beans,
confirm with '.
Individual beverages
Individual beverages You can define and save instructions for up to
8individual beverages.
1Turn the function selector to one of the 8memory
locations.
2Use the Csymbol to successively select the
desired beverage, size, strength, temperature and
coffee-milk ratio and use the rotary selector to save
the settings.
3Enter the name of the beverage in "ABC".
Rotary selec-
tor
Selects letters
A new word always begins with a capital let-
ter.
4Press briefly: moves the cursor to the right
Press and hold: shifts to umlauts and spe-
cial characters
Press twice: adds a line break
5Press briefly: moves the cursor to the right
Press and hold: shifts to normal characters
Press twice: adds a line break
lDelete letters
&DSSXFFLQR
7RPV
&DSSXFFLQB

18
en Child lock
4Save with ™or cancel with 'and exit the menu.
5Press Ito start.
Depending on the beverage selected, the beans will be
ground first, then the milk prepared and finally the
coffee brewed.
Notes
– While the beverage is dispensed, the &symbol is
displayed. Touch this symbol to stop the beverage
being prepared.
– For entering a name, Latin characters, certain
special characters and numbers are available.
– To change an existing memory location, touch the
%symbol and save a new setting.
– If a memory location which is already occupied is
selected, the settings will be overwritten.
Child lock
Childlock The appliance has a child lock to prevent children
operating it accidentally.
Notes
– You must set the child lock to "Available" in Basic
settings. ~"Basic settings" on page 19
– If there is a power failure while the child lock is
activated, it may be deactivated when power is
restored.
Activating the child lock
Prerequisite:
The function selector is set to 0.
Touch the 0symbol for at least 6 seconds.
The child lock is now activated. The 0symbol is shown
at the top of the display.
Deactivating the child lock
Prerequisite:
The function selector is set to 0.
Touch and hold the 1symbol for at least 6 seconds.
The child lock is deactivated. You can set the appliance
as normal.

19
Basic settings en
Basic settings
Basicsetti ngs Your appliance can be individually adjusted in the basic
settings.
1Turn the function selector to S.
2Select "Basic settings" using the rotary selector.
3Touch the ™symbol.
4Turn the rotary selector to select the required basic
setting.
5Touch the %symbol.
6Set the basic setting using the rotary selector.
7Save with ™or cancel with 'and exit the current
basic setting.
8Turn the function selector to 0to exit the basic
settings menu.
The changes are saved.
Basic setting Permitted settings Explanation
Brightness Level 1, 2, 3, 4, 5*, 6, 7, 8 Sets the display brightness
Display Reduced*/Standard If the 'Reduced' setting has been selected,
only the most important information will be
shown on the display after a short time.
Touch field colour Grey* / White Selects the colour of the symbols on the
touch fields
Touch field tone Tone 1* / Tone 2/ Off Selects an audible signal for when a touch
field is touched
Touch field tone vol-
ume
Level 1, 2, 3, 4, 5*, 6, 7, 8 Sets the volume of the touch field tone
Signal volume Level 1, 2, 3, 4, 5*, 6, 7, 8 Sets the volume of the audible signal
Light settings Lighting options 1*-7 ÛLight off
ÚLight on
~Light only on when a beverage is being
dispensed
Other setting options will appear if you
touch the %symbol.
Standby after 5minutes - 3hours Setting for the time after which the appli-
ance automatically rinses and switches to
standby mode.
Water hardness 1-4*, softening device Briefly immerse the enclosed test strip in
fresh tap water, leave it to drip and read off
the result after one minute. Set the meas-
ured water hardness.
Water filter Available/not available* Available: Operating the appliance with a
water filter.
Not available: Operating the appliance with-
out a water filter.
Temperature unit °C* / °F Setting the temperature unit
Capacity unit ml/fl.oz.* Set the capacity unit
Capacity +/ 5ml to 60ml
(0.2fl.oz to 2fl.oz)
Adjust the capacity to individual cup sizes.
First select the beverage and then set the
capacity.

20
en Basic settings
--------
Weight unit g*/oz. Set the weight unit
Milk container weight Standard*/Individual Setting for weight detection. ~"Setting
the milk container weight" on page 21
Language German* / French / Italian / Spanish /
Portuguese / Dutch / Danish / Swedish
/ Norwegian / Finnish / Greek / Turkish
/ Russian / Polish / Czech / Slovenian /
Slovakian / Arabic / Hebrew / Japanese
/ Korean / Thai / Chinese / English US
/ English
Select language for text display
Note:
If the language is changed, the system
restarts. This takes a few seconds.
The basic settings menu is also closed.
Factory settings Reset the appliance to the factory set-
tings
Confirm the question "Delete all individual
settings made and reset to factory set-
tings?" by pressing ™or cancel by press-
ing '.
Note:
Individual drinks will also be deleted if the
appliance is reset to factory settings.
After resetting the factory settings, the "Ini-
tial settings" menu is displayed.
Demo mode On / Off* Only for demonstration purposes. The "Off"
setting must be activated for normal opera-
tion. The setting is only possible in the first
3 minutes after switching on the appliance.
Milk container
reminder
30* minutes - 6 hours Setting for the time after which the reminder
appears.
Child lock Not available*/Available Available: The child lock can be activated.
~"Child lock" on page 18
* Factory setting