Gaggenau Vario 400 Series User manual

VR 414 610
Stainless steel
Width 15" (38 cm)
Included accessories
1 cast-iron griddle, half size
1 grease collecting insert
2 cast-iron grills
1 lava stone
1 cleaning brush
Installation accessories
In combination of several Vario
cooktops or VL 414 downdraft,
connecting strips must be used.
Choose respective VA 420 strip from
one of the below, depending on type
of installation.
VA 420 000
Connection strip for combination
with other Vario 400 series appliances
for flush mounting.
VA 420 010
Connection strip for combination
with other Vario 400 series appliances
for surface mounting.
VA 440 010
Stainless steel appliance cover with
mounting strip.
Only available for individual Vario
installation.
Optional accessories
LV 030 000
Lava stones for refilling.
VA 461 000
Cast-iron griddle, enameled, half size
For Vario electric grill 400 series.
For simultaneous searing and grilling
on two separate surfaces.
VA 461 001
Cast-iron griddle, enameled, full size
For Vario electric grill 400 series.
For searing large quantities on one
surface.
Vario 400 series electric grill
VR 414
– Two zones,can be operated
together or separately
– Half size cast-iron griddle included
for simultaneous searing and
grilling on two separate surfaces
– Open cast-iron grill, lava stones
– Solid stainless steel control knobs
– Precision-crafted 3 mm stainless
steel
– For surface mounting with a visible
edge or for flush mounting
– Can be combined with other Vario
400 series products
Operation
Control knobs with illuminated
ring, cooking zone and output level
markings.
Electronic control in 12 output levels.
Features
Cooktop, lavas tone trough and grease
collecting insert are stainless steel.
Two zones, each 1500 W, can be
operated together as a complete
surface or each half separately.
Safety
Safety shut-off.
Pre-heat and residual heat indicator.
Planning notes
Depending on the type of installation —
surface-/ or flush-mounted — the
specific location of the control knob
positions may vary.
If installing with appliance cover
VA 440 take into account the additional
space required for the depth.
If combining several Vario 400
series, appliances a connection
strip must be placed between the
appliances. Depending on the type
of installation — surface-/ or flush-
mounted — the corresponding VA 420
connecting strip must be provided.
The weight bearing capacity
and stability, in the case of thin
countertops in particular, must
be supported using suitable
substructures. Take into account the
appliance weight and additional loads.
Additional instructions for flush mounting:
Installation is possible in countertops
made of stone, synthetics or solid wood.
Heat resistance and watertight sealing
of the cut edges must be observed.
Concerning other materials please
consult the countertop manufacturer.
The groove must be continuous and
even, so that uniform placing of the
appliance on the gasket is ensured.
Do not use discontinuous lining.
The joint width may vary due to size
tolerances of the combinations and of
the countertop cut-out.
Please read additional planning notes
on pages 108 – 113.
If installing several appliances in
individual cut-outs allow for a minimum
distance of 2" between the cooktops.
A minimum lateral clearance of at least
4" from adjacent heat-sensitive
cabinets or from the wall must be
observed.
Appliance can be snapped into the
countertop from above.
Appliance weight: approx. 57.3 lbs.
Rating
Total rating: 3 kW.
Total Amps: 16 A.
208/220–240V / 60 Hz
Plan for a 70" connecting cable
without plug (hardwire required).
www.gaggenau.com/us
Revised: 31 March 2020

Numbers indicated
inside parenthesis ( ) = mm
R
1
/
8
" (R 3)
90°
70" (1.8 m)
A:
When installing with appliance cove, take the deeper cut-out
into consideration(see separate planning notes)
B:
5
1
/
8
" (130 mm) in the area of the cable clamp (left, on the rear side).
min. 4
1
/
8
" (105)
max. 6
3
/
8
" (162)
min. 2"
(50)
dia. 2
1
/
8
"
(60)
dia. 1
3
/
8
" (35)
min. 1
3
/
8
" (35)
19
3
/
8
"
±1
/
16
" (492
±2)
14
15
/
16
"
(380)
20
1
/
2
" (520) (A)
1
/
8
" (3)
14
3
/
16
"
±1
/
16
"
(360
±2
)
3
9
/
16
" (90)
4
1
/
2
" (115) (B)
5
1
/
2
"
(140)
8
15
/
16
"
(227)
11"
(280)
3" (76)
(A)
1
/
8
"
(3.5
-0.5
)
R
1
/
8
" (3)
R
3
/
16
"
(5
+1
)
min. 1
3
/
8
" (35)
min. 4
1
/
4
" (109)
max. 6
1
/
2
" (166)
min. 2"
(50)
dia. 2
1
/
8
"
(60)
dia. 1
3
/
8
" (35)
70" (1.8 m)
90°
14
15
/
16
"
(380)
20
1
/
2
" (520) (A)
19
3
/
8
"
±1
/
16
" (492
±2
) (A)
20
11
/
16
"
+1
/
16
" (526
+2
) (A)
4
5
/
8
" (118) (B)
1
/
8
"
(3)
14
3
/
16
"
±1
/
16
"
(360
±2
)
15
3
/
16
"
+1
/
16
"
(386
+2
)
3
9
/
16
"
(90)
5
1
/
2
"
(140)
8
15
/
16
"
(227)
11"
(280)
3" (76)
When installing with appliance cover, pay attention to the deeper cut-out and the front and
rear groove width.
Surface-mount Installation Flush-mount Installation
Control knob installation, surface-mounted installation
ø 1
3
/
8
" (35)
ø 1
3
/
8
" (35)
min.
3
/
16
" (5)
min.
3
/
16
" (5)
4
1
/
8
"-6
3
/
8
"
(105-162)
4
1
/
8
"-6
3
/
8
"
(105-162)
5
/
8
"-1"
(16-26)
D =1" (26)
D
>
1" (26)
3
1
/
8
"x12
3
/
16
"
(80x310)
Installation of the control knob; surface-mount installation
Control knob installation, flush-mounted installation
ø 1
3
/
8
" (35)
ø 1
3
/
8
" (35)
min.
3
/
16
" (5)
min.
3
/
16
" (5)
4
1
/
4
"-6
1
/
2
"
(109-166)
4
1
/
4
"-6
1
/
2
"
(109-166)
5
/
8
"-1"
(16-26)
D =1" (26)
D
>
1" (26)
3
1
/
8
"x12
3
/
16
"
(80x310)
Installation of the control knob; flush-mount installation
fill with
silicone
Longitudinal section
1
/
8
" (
3,5
-0,5
)
14
3
/
16
"
±1
/
16
"
(360
±2
)
14
15
/
16
"
(380)
15
3
/
16
"
+1
/
16
"
(386
+2
)
1
/
2
"
(13)
1
/
2
"
(13)
1
/
8
"
(3
+1
)
1
/
8
"
(3
+1
)
Longitudinal section
Cross-section
fill with
silicone
1
/
8
" (
3.5
-0.5
)
19
3
/
8
"
±1
/
16
"
(492
±2
)
20
11
/
16
"
+1
/
16
"
(526
+2
)
11
/
16
"
(17)
11
/
16
"
(17)
1
/
8
"
(3
+1
)
1
/
8
"
(3
+1
)
20
1
/
2
"
(520)
When installing with appliance cover or adjustment strip, pay attention to
the deeper cut-out and the front and rear groove width.
Cross-section
A: When installing with appliance cove, take the deeper cut-out into consideration. See
separate planning notes on page 113.
B: 5 ⅛" (130 mm) in the area of the cable clamp (left, on the rear side).
A: When installing with appliance cove, take the deeper cut-out into consideration. See
separate planning notes on page 113.
B: 5 ⅛" (130 mm) in the area of the cable clamp (left, on the rear side).
* with appliance cover or adjustment bar
(observe front and rear asymmetrical assembly,
see separate notes "assembly with
appliance cover/adjustment bar").
View from above
R
3
/
16
"
(R 5
+1
)
R
1
/
8
"
(R 3)
14
3
/
16
"
±1
/
16
"
(360
±2
)
15
3
/
16
"
+1
/
16
"
(386
+2
)
20
11
/
16
"
+1
/
16
"
(526
+2
)
19
3
/
8
"
±1
/
16
"
(492
±2
)
View from above
A: When installing with appliance
cover consider the deeper cut-out
See separate notes “assembly
with appliance cover” on page
113).
www.gaggenau.com/us
Revised: 31 March 2020