Galaxy EPABX 206 Owner's manual

Programming Manual
Model: 206/308/412/416/424/432
TM
TM

SYSTEM PROGRAMMING
TO ENTER INTO PROGRAMMING MODE
Dial 1# + Password (Initial Password is 6336)
If password is right then confirmation tone else NU tone
Now you can dial codes as given below:
1) To Reset the System
01 + 91
2) To Program Default Settings
01 + 91 + 6336
3) To Set System Configuration
01 + 206 ÝFor 206 System
01 + 308 ÝFor 308 System
01 + 412 ÝFor 412 System
01 + 416 ÝFor 416 System
01 + 424 ÝFor 424 System
01 + 432 ÝFor 432 System
4) Call Pick-up Selection
01 + 80 ÝCall pickup Code - 8
01 + 89 ÝCall pickup Code - 8 / 88 / 8 + Extn No
5) To Set Operator 9
01 + 90 ÝFor Operator Call 9
01 + 99 ÝFor No Operator Call 9
6) To Change System Password
02 + New 4 digit PSW + Repeat New 4 Digit PSW
7) To Program Day Mode Landing
03 + CO No. + Ring Type + Extn Nos (Max 5 Extn Nos)
Ring Type 0 ÝSimultanous Ringing
3 ÝRound Robin with 3 Rings
4 ÝRound Robin with 4 Rings
5 ÝRound Robin with 5 Rings
6 ÝDID Message
Galaxy 412
}
}
Galaxy 432
3

DID Message
0 ÝDID Without Message
1 ÝDID With 1st Message
2 ÝDID With 2nd Message
9 ÝDID Cancellation
8) To Program Night Mode Landing
04 + CO No. + Ring Type + Extn Nos (Max 5 Extn Nos)
9) To Program CO Settings
05 + CO No. + 0 ÝTK out going allowed
1 ÝTK out going barred
2 ÝTK incoming allowed
3 ÝTK incoming barred
4 ÝTK CLI after 1st Ring
5 ÝTK CLI before 1st Ring
6 ÝRing Disconnection duration 3 sec
7 ÝRing Disconnection duration 5 sec
90 Ý0 or 7 Normal Trunk Access
91 Ý0 or 7 Hunting Trunk Access
98 ÝNormal CO Line
99 ÝCentrex CO Line
10) To Program CO Group
06+0+CO Nos (71 to 74/79 All CO Bar/70 All CO allowed)
06+7+CO Nos (71 to 74/79 All CO Bar/70 All CO allowed)
11) To Set CO Lines Access Rights
06+Extn No.+CO Nos (71to74/79 All CO Bar/70 All CO allowed)
4

12) To Program Extn Class of Service (COS)
08 + Day COS + Night COS + Extn Nos
COS 0 ÝOnly Intercom
1 ÝLocal Calls
2 ÝLocal + Mobile Calls
3 ÝLocal + Mobile + STD Calls
4 ÝAll allowed
13) To programme single shot settings
08 +90 ÝFlash Time 100 to 600 msec for all Extns
91 ÝFlash Time 600 to 1000 msec for all Extns
92 ÝCLI Disable for all Extns
93 ÝCLI Enable for all Extns
94 ÝEnable Particular Trunk Dialing (71, 72, 73, 74)
95 ÝDisable Particular Trunk Dialing (71, 72, 73, 74)
96 ÝGlobal Dialing Enable for all Extns
97 ÝGlobal Dialing Disable for all Extns
14) To Program Extension Settings
09 + Extn No. + 0 ÝFlash Timing (300 msec)
1 ÝFlash Timing (600 msec)
2 ÝDisable Extn CLI
3 ÝEnable Extn CLI
4 ÝTrunk Unlimited
5 ÝTrunk 5 mins Limited
6 ÝEnable Global Memory Dialing
7 ÝDisable Global Memory Dialing
91 ÝExtn Default Setting
5

15) To Program Extension Feautres
10 + Extn No. + 0 ÝEnable DND & Call forward
1 ÝDisable DND & Call forward
2 ÝEnable Hot Line & Dedicate CO
3 ÝDisable Hot Line & Dedicate CO
4 ÝEnable Conference & Barge In
5 ÝDisable Conference & Barge In
6 ÝDisable Barge in Protect
7 ÝEnable Barge in Protect
8 ÝDisable Barge in Protect with Tone
9 ÝEnable Barge in Protect with Tone
16) To Set Operator Extension
11+1 + Extn No. ÝFirst Operator Extn
11+2 + Extn No. ÝSecond Operator Extn
11+3 + Extn No. ÝFax Extn
17) To Program Extns Features
12 + Extn No. + 0 ÝDisable Paging Extns
1 ÝEnable Paging Extns
2 ÝSet Normal Ringing Extn type
3 ÝSet Executive Ringing Extn type
4 ÝEnable Particular Trunk Dialing
5 ÝDisable Particular Trunk Dialing
6 ÝDisable Denied Dialing
7 ÝEnable Denied Dialing
18) Denied/Restricted (D/R) Entries
13 + Extn No. + D/R Type + Code (max 3 digits) + *
D/R 0 ÝDenied
1 ÝRestricted
(Each Extn has maximum 5 Entries)
6

19) To Record and Play Message
19 + 01 + * ÝTorecord 1st Message
02 + * ÝTo record 2nd Message
03 + * ÝTo Play 1st Message
04 + * ÝTo Play 2nd Message
20) To Program Default Extn Numbers
20+00 ÝDefault 2 Digit Extn Nos. Starting from 21
30+00 ÝDefault 3 Digit Extn Nos. Starting from 201
40+00 ÝDefault 4 Digit Extn Nos. Starting from 2001
21) Flexible Number Programming
21 + Port No + * + New 2 Digit No + *
31 + Port No + * + New 3 Digit No + *
41 + Port No + * + New 4 Digit No + *
22) Continuous Flexible Number Programming
29 + Port No + * + Starting New 2 Digit No + * +
Ending New 2 Digit No.
39 + Port No + * + Starting New 3 Digit No + * +
Ending New 3 Digit No.
49 + Port No + * + Starting New 4 Digit No + * +
Ending New 4 Digit No.
23) To Set Time, Date & Day
22 + 0 + HH + MM + SS ÝTime in 24 Hour Format
1 + DD + MM + YY
2 + Day Ý1=Mon, 2=Tue, 3=Wed, 4=Thur,
5=Fri, 6=Sat & 7=Sun
3 ÝAuto D/N mode
4 ÝManual D/N Mode
5 ÝNA
6 ÝVoice Enable
7

7 ÝDisable DID & Voice
8 + Seconds (00 - 59) ÝVoice Duration Setting
90 Delayed Landing after VG Message
91 Without Delayed Landing after VG Message
92 DID Call Landing after 5 Rings
93 DID Call Landing after 9 Rings
24) To Set Auto Day & Night Mode Timings
23+Day+Day Start Time HH/MM+Day End Time HH/MM
25) To Clear Global Memory Area
19 + 09 + *
26) To Program Global Memory dialing
900 to 989 + 00 / 71-74 / 07 + Telephone No. + #
00 (For any CO Line) / 71-74 (Particular CO)/
07 (CO Group)
*Features of Model Specific
8