GALCO EX95000 Series User manual

Hardened Ethernet Switch
Quick Start Guide
This quick start guide describes how to install and use the
Hardened Ethernet Switch. This is the switch of choice for
harsh environments constrained by space.
Physical Description
The Terminal Block and Power inputs
Power Input Assignment
Power3 12VDC DC Jack
＋12-48VDC
Power2 －Power
Ground
＋12-48VDC
Power1 －Power
Ground
Earth Ground
Terminal
Block
Relay Alarm Assignment
1

Hardened Ethernet Switch
FAULT
*Relay warning signal disable for
following:
The relay contact closes if Power1 and
Power2 are both failed but Power3 on.
The relay contact closes if Power3 is
failed but Power1 and Power2 are both
on.
DC Terminal Block Power Inputs: There are two pairs of
power inputs can be used to power up this switch. Redundant
power supplies function is supported.
The 10/100Base-TX and 100Base-FX/BX Connectors
1. The 10/100Base-TX Connections
The following lists the pinouts of 10/100Base-TX ports.
Pin Regular Ports Uplink port
1 Output Transmit Data + Input Receive Data +
2 Output Transmit Data - Input Receive Data -
3 Input Receive Data + Output Transmit Data +
4 NC NC
5 NC NC
6 Input Receive Data - Output Transmit Data -
7 NC NC
8 NC NC
2. The 100Base-FX Connections
The fiber port pinouts: The Tx (transmit) port of device I is
connected to the Rx (receive) port of device II, and the Rx
(receive) port of device I to the Tx (transmit) port of device II.
2

Hardened Ethernet Switch
3. The WDM 100Base-BX Connections
The fiber port pinouts: Only one single-mode optical fiber is
required to transmit and receive data.
The Port Status LEDs
3

Hardened Ethernet Switch
LED State Indication
10/100Base-TX, 100Base-FX/BX
Steady A valid network connection established.
Link/ACT
(Green) Flashing Transmitting or receiving data.
ACT stands for ACTIVITY.
4

Hardened Ethernet Switch
5
Functional Description
•Meets NEMA TS1 & TS2 environmental requirements
for traffic control equipment.
•Meets EN61000-6-2 & EN61000-6-3 EMC Generic
Standard Immunity for industrial environment.
•Supports IEEE802.3/802.3u/802.3x. Auto-negotiation:
10/100Mbps, Full/Half-duplex, Auto-Negotiation, Auto
MDI/MDIX.
•100Base-FX: Multi/Single mode SC or ST type.
100Base-BX: WDM Single mode SC type.
•Supports 4096 MAC addresses. Provides 1.625M bits
buffer memory.
•Alarms for power failure by relay output 1A @ 24VDC.
•Power Supplies: Redundant 12-48VDC Terminal Block
power inputs and 12VDC DC JACK with 100-240VAC
external power supply.
•Field Wiring Terminal: Use Copper Conductors Only,
60/75℃, 14-24 AWG torque value 4.5 lb-in.
•Operating voltage and Max. current consumption: 0.7A
@ 12VDC, 0.35A @ 24VDC, 0.175A @ 48VDC. Power
consumption: 8.4W Max.
•-40℃to 75℃(-40℉to 167℉) operating temperature
range. Tested for functional operation @ -40℃to 85℃
(-40℉to 185℉). UL508 Industrial Control Equipment
certified Maximum Surrounding Air Temperature @ 75℃
(167℉).
•For use in Pollution Degree 2 Environment.
•Supports DIN-Rail or Panel Mounting installation.
Assembly, Startup, and Dismantling
•Assembly: Place the switch on the DIN rail from above
using the slot. Push the front of the switch toward the
mounting surface until it audibly snaps into place.

Hardened Ethernet Switch
•Startup: Connect the supply voltage to start up the
switch via the terminal block (or DC JACK).
•Dismantling: Pull out the lower edge and then remove
the switch from the DIN rail.
6

Hardened Ethernet Switch
7
Preface
A member of the growing family of rugged switches, this
switch addresses a need for a smaller switch. This switch
provides an affordable solution for rugged and outdoor
environment, transportation road-side cabinet, industrial
floor shop, multitenant dwellings or Fiber To The Home
(FTTH) applications. Capable of operating at temperature
extremes of -40°C to +75°C, this is the switch of choice for
harsh environments constrained by space.
Plug-and-Play Solution:
The switch is a plug-and-play Fast Ethernet Switch in
compact size. It doesn't have any complicated software to
set up.
This manual describes how to install and use the hardened
Ethernet Switch. This switch integrates full wire speed
switching technology. This switch brings the answer to
complicated hardened networking environments.
To get the most out of this manual, you should have an
understanding of Ethernet networking concepts.
In this manual, you will find:
yFeatures on the switch
yIllustrative LED functions
yInstallation instructions
ySpecifications

Hardened Ethernet Switch
8
Table of Contents
QUICK START GUIDE 1
PHYSICAL DESCRIPTION 1
The Terminal Block and Power inputs 1
The 10/100Base-TX and 100Base-FX Connectors 2
The Port Status LEDs 3
FUNCTIONAL DESCRIPTION 5
ASSEMBLY,STARTUP,AND DISMANTLING 5
PREFACE 7
TABLE OF CONTENTS 8
PRODUCT OVERVIEW 9
HARDENED ETHERNET SWITCH 9
PACKAGE CONTENTS 9
PRODUCT HIGHLIGHTS 10
Basic Features 10
FRONT PANEL DISPLAY 11
PHYSICAL PORTS 12
INSTALLATION 13
SELECTING A SITE FOR THE SWITCH 13
DIN RAIL MOUNTING 14
WIRING DIAGRAM 15
CONNECTING TO POWER 16
Redundant DC Terminal Block Power Inputs 16
12VDC DC Jack 16
Alarms for Power Failure 17
CONNECTING TO YOUR NETWORK 18
Cable Type & Length 18
Cabling 19
SPECIFICATIONS 20
APPENDIX A–CONNECTOR PINOUTS 22

Hardened Ethernet Switch
Product Overview
Hardened Ethernet Switch
Package Contents
When you unpack the product package, you shall find the
items listed below. Please inspect the contents, and report
any apparent damage or missing items immediately to your
authorized reseller.
3This Switch
3User’s Manual
3External power adapter & Power Cord
(Optional)
9

Hardened Ethernet Switch
10
Product Highlights
Basic Features
•Meets NEMA TS1 & TS2 Environmental requirements
such as temperature, shock, and vibration for traffic
control equipment.
•Meets EN61000-6-2 & EN61000-6-3 EMC Generic
Standard Immunity for industrial environment.
•Support 802.3/802.3u/802.3X.
•Auto-negotiation: 10/100Mbps, Full/Half-duplex; Auto
MDI/MDIX.
•Support 4096 MAC addresses.
•Provides 1.625M bits memory buffer.
•Alarms for power failure by relay output 1A @ 24VDC.
•Power Supplies: Redundant 12-48VDC Terminal Block
power inputs and 12VDC DC JACK with 100-240VAC
external power supply.
•Field Wiring Terminal: Use Copper Conductors Only,
60/75℃, 14-24 AWG torque value 4.5 lb-in.
•Operating voltage and Max. current consumption: 0.7A
@ 12VDC, 0.35A @ 24VDC, 0.175A @ 48VDC. Power
consumption: 8.4W Max.
•-40℃to 75℃(-40℉to 167℉) operating temperature
range. Tested for functional operation @ -40℃to 85℃
(-40℉to 185℉). UL508 Industrial Control Equipment
certified Maximum Surrounding Air Temperature @ 75℃
(167℉).
•For use in Pollution Degree 2 Environment.
•Supports DIN-Rail or Panel Mounting installation.