Galiso LDD-4 User manual

LDD-4
GALISO LIGHT DUTY DRYER
INSTALLATION/OPERATION INSTRUCTION MANUAL
MANUAL NUMBER 21-11-1027
Issued July 2018
Copyright 2018, Galiso, Inc.
22 Ponderosa Ct., Montrose, CO 81401
[phone] [phone]
www.galiso.com

!!!DANGER!!!
DO NOT USE THIS EQUIPMENT TO
PURGE TOXIC OR FLAMMABLE GAS
AND
DO NOT USE THIS EQUIPMENT UNDER
FLAMMABLE, VOLATILE OR TOXIC
ENVIRONMENTAL CONDITIONS

TABLE OF CONTENTS
Section/Title Page
1.0 Introduction...................................................................................1-1
2.0 Specifications................................................................................2-1
3.0 Safety............................................................................................3-1
4.0 Installation.....................................................................................3-1
5.0 Operation......................................................................................4-1
6.0 Maintenance .................................................................................4-1
7.0 Spare Parts –110Volt...................................................................5-1
7.1 Spare Parts –220Volt............................................................5-2
List of Tables and Figures
Number/Title Page
Figure 1, LDD-4 Galiso Cylinder Dryer.............................................2-1
Figure 2, Spare Parts Components, 110 Volt...................................5-1
Figure 3, Spare Parts Components, 220 Volt...................................5-2
2018 Galiso Inc.

21-11-1027 Section 1 - 1
1.0 INTRODUCTION
The LDD-4 Galiso Light Duty Dryer has been designed to quickly dry up to four drained
cylinders in a matter of minutes.
The LDD-4 Cylinder Dryer features a heavy duty blower and can generate 95 CFM of
hot or cold air. The built in Dryer motor is quiet, and can produce temperatures up to
175°F to accelerate the drying of steel and aluminum cylinders. “Cool” can be selected
to use non-heated air for protection of fiber wrapped or composite cylinders.
The LDD-4 series Dryer is available in 110 Volt 50/60Hz or 220 Volt 50/60 Hz options.
In addition to the LDD-4 series cylinder dryer, Galiso®also offers the Heavy Duty (HDD)
for large cylinders, the Galiso Cylinder Dryer (GCD-4) and the Small Cylinder Dryer
(SCD) for washing and drying small cylinders.

Section 2 - 1 21-11-1027
2.0 SPECIFICATIONS
CAUTION
HOT
SURFACES!
Blower / Motor
Front
Legs
Electrical Plug
110V, 50/60 Hz, 20 Amp
220V, 50/60 Hz, 12 Amp
Rear
Leg
Control
Box
3-Position
Power Switch
Heat, Cool, Off
Dryer
Probes
x 4
Figure 1, LDD-4 Galiso Light Duty Dryer
Power Requirements: 110 Volt, single phase, 50/60Hz, 20 Amp
220 Volt, single phase, 50/60 Hz, 12 Amp
Blower Motor: generates 95 CFM of hot or cold air.
Dimensions (frame and blower assembly): 59x20x72
Capacity: up to 4 –60” tall.
Decibels: from 5 dB to 75.7dB
Warranty: One Year (see Galiso Warranty Terms, Form No GSO7805-1).

21-11-1027 Section 3 - 1
3.0 SAFETY
Read all instructions before attempting to install or operate this machine. GALISO,
INCORPORATED IS NOT RESPONSIBLE FOR DAMAGE OR INJURY CAUSED BY
UNSAFE USE, MAINTENANCE, APPLICATION, MODIFICATION OR IMPROPER
INSTALLATION OF THIS MACHINE. Please contact Galiso, Inc. for guidance when you
are in doubt as to the proper safety precautions to be taken when installing or operating
this machine.
A. Take care to keep the work area around the LDD-4 clean, dry and free of debris.
This will decrease the chance of operator injury due to slips or falls.
B. Always wear gloves, eye protection and foot protection while operating the LDD-
4.
C. The LDD-4 Dryer is capable of producing considerable heat. Use insulating
gloves to protect hands against possible burns from hot areas and items.
D. Do not cover motor fan cowl. Do not drop screwdrivers, nails, etc., into the
openings of the fan cowl.
E. Make sure to bolt, lag or clip the LDD-4 securely to the floor.
4.0 INSTALLATION
A. Read all instructions and familiarize yourself with the installation blueprints before
attempting to install or operate the LDD-4 Cylinder Dryer.
B. Carefully uncrate the LDD-4 Cylinder Dryer and remove all packing materials.
If there are any missing or damaged parts, please call Galiso, Inc. at 1 (800) 854-
3789 and DO NOT attempt to install any pieces until concerns and possible safety
issues have been discussed.
C. The installation location should insure adequate clearance for unprotected shop
personnel, and close to the power outlet.
D. After the Dryer has been placed in its permanent location, bolt, lag or clip to the
floor.

Section 4 –1 21-11-1027
5.0 OPERATION
A. Galiso, Inc. recommends a warm up time of approximately 2 minutes at the start-
up of the machine. Switch the Power Switch to the HEAT position. After the warm
up, the Power Switch can remain in the HEAT position, or be switched to COOL
or OFF
B. Check that the cylinders are emptied and drained of water.
C. Invert drained cylinder and place upside down with a manifold outlet inserted into
the cylinder neck.
! CAUTION !
Avoid bending or otherwise damaging the tube.
D. When cylinders have been loaded, flip the Power Switch to the HEAT or COOL
position.
E. After cylinders have been drying for a short time (5-10 minutes), check each
cylinder for dryness, and replace on the dryer if necessary or, load the next
cylinder.
NOTE: Cylinder dry times can vary, depending on the size and/or material.
Galiso, Inc. recommends using the COOL setting for composite cylinders.
! CAUTION !
The dryer can remain “On” when changing out cylinders but
the operator should be careful to avoid touching the Manifold
Frame, as it may be hot.
F. To shut down at the end of the day, flip the Power Switch to “COOL” for
approximately 2 minutes for the unit to cool down before flipping to the “OFF”
position.
6.0 MAINTENANCE
A. No regular maintenance is required except to check the air filter on top of the
muffler at least once a month and replace if needed.

21-11-1027 Section 5 - 1
7.0 SPARE PARTS –110 Volt
The LDD-4 has been designed with modular components for ease of replacing parts
if necessary. See Figure 2 or 3 (dependent on the voltage of your machine),
Replacement Components.
Electrical
Enclosure
Assembly
Fuse 20 Amps
Blower /
Filter
Assembly
Heater
Tube
Assembly 110 Volt
Components
25-41-3191
88-11-0054
A.
D.
C.
B.
25-41-3186
25-43-3024
Figure 2, Spare Parts -110V
Item
Part No.
Description
A.
25-41-3191
Electrical Enclosure Assembly
B.
25-41-3186
Blower / Filter Assembly
C.
25-43-3024
Heater Tube Assembly
D.
88-11-0054
Fuse, 20 Amps

Section 5 –2 21-11-1027
7.1 SPARE PARTS –220 Volt
The LDD-4 has been designed with modular components for ease of replacing parts
if necessary. See Figure 2 or 3 (dependent on the voltage of your machine and code
requirements), Replacement Components:
Electrical
Enclosure
Assembly
Heater
Tube
Assembly
220 Volt
Components
25-41-3196
(US coded)
A.
C.
European Standard
B. 25-41-3197
(CE coded)
Blower /
Filter
Assembly
D.
25-41-3188
25-41-3025
OR
Fuse 15 Amps
250V, 1-1/4” x 1/4”
88-11-0053
E.
Figure 3, Spare Parts -220V
Item
Part No.
Description
A.
25-41-3196
Electrical Enclosure Assembly US Coded
B.
25-41-3197
Electrical Enclosure Assembly CE Coded
C.
25-43-3025
Heater Tube Assembly
D.
25-41-3188
Blower / Filter Assembly
E.
88-11-0053
Fuse, 15 Amp, 250V, 1-1/4” x ¼”

PRODUCT WARRANTY
1. DURATION: Galiso provides a one-year warranty from date of purchase, to the original purchaser, for
standard products, unless otherwise specified. For all spare parts purchases, Galiso provides a 90-day
warranty unless otherwise specified. Soft goods such as our speed seals, and O-rings, which are subject
to wear in the normal course of operation, are not covered under this warranty.
2. COVERAGE: Galiso manufactured equipment is warranted against defective materials or workmanship.
THIS WARRANTY IS VOID IF:
A) THE EQUIPMENT HAS BEEN DAMAGED BY ACCIDENT OR UNREASONABLE USE,
IMPROPER SERVICE/MAINTENANCE, IMPROPER INSTALLATION, ABNORMAL OPERATING
CONDITIONS, NEGLECT, REPAIR BY ANY PERSON NOT AUTHORIZED BY GALISO, INC.
OR OTHER CAUSES NOT RELATED TO MATERIAL DEFECTS OR WORKMANSHIP.
B) THE SERIAL NUMBER HAS BEEN ALTERED OR DEFACED.
3. PERFORMANCE: Galiso reserves the right to make warranty determination only after inspecting the item
at the Galiso manufacturing facility. If the warranty determination indicates that the defective item is
covered under warranty, the item will be repaired or replaced with the same parts/items or parts/items of
equivalent quality, at the option of Galiso. In the event of replacements, the replacement unit will continue
under the original equipment warranty or carry a 90-day warranty, whichever is longer. No charge will be
made for warranty repairs, and/or replacements. All freight charges to and from Galiso Inc. or a Galiso
Inc. authorized repair facility, are the responsibility of the customer requesting warranty service.
If the warranty determination indicates that the item is not covered by warranty, a repair/replacement cost
estimate will be submitted to the customer/purchaser for approval prior to initiating any repair work.
4. CLAIMS: In the case of equipment malfunction, notify Galiso (1-800-854-3789) and provide the Model
Name, Model Number, Serial Number and a description of the problem. Return Authorization Number,
shipping and/or service information will be provided on receipt of the required information.
5. SERVICE EQUIPMENT: Galiso attempts to make available, whenever possible, a limited amount of
service equipment at a minimal use charge, plus freight expense, for those customers wishing to avoid
downtime during repair of their equipment. Such items are available on a first come, first served basis and
are billable at the specific service charge applying with a one-month minimum.
6. MODEL CHANGES: Galiso reserves the right to make changes in materials and specifications, without
notice. Galiso may offer, for a stipulated fee, the opportunity to upgrade your equipment to the latest
configuration.
7. DISCLAIMERS: Galiso provides technical data and assistance to aid customers in the selection and use
of our products. There are no implied warranties of merchantability nor suitability for a particular purpose
associated with the transmittal of technical data and/or customer assistance.
Galiso does not assume liability for any consequential, incidental, or special damages. Liability under this
warranty is limited to repairing, or replacing Galiso equipment items returned to the factory or an
authorized facility.
8. COMPUTER AND NETWORK VIRUS PROTECTION: Galiso Inc. equipment, which utilizes internet
access, comes equipped with a subscription to virus protection software. It is the responsibility of the
equipment owner to maintain this virus protection subscription or other virus protection at their cost.
Current virus subscriptions are mandatory to maintain the benefits of this warranty. Galiso does not
assume liability for any or all damages related to or are the result of internet or network failure or malware
or computer viruses or any other type of internet or network malfunction or attack.
GSO9102-1E 05/31/12 Supersedes: 01/07/02