GAMA Electronics LRF120VPR1L User manual

LRF120VPR1L
Instruction Manual
WWW.GAMAINC.COM
Included in this Kit:
(1) LRF120VPR1L Receiver
(1) 3-Button Transmitter with Light
Available accessories:
- Wireless Outdoor Keypad KP340-DRC
- 3-Button Waterproof Transmitter KF340-3L-WP
The LRF120VPR1L is an RF receiver operating at a fixed frequency of 340 MHZ. It operates from 120VAC and provides
one polarity reversing output for use with a four/six lead AC motor. The receiver is not designed to operate with any
existing hand or drum switch. The receiver is equipped with a manual toggle switch. An additional latching output is
available for connecting to a 120VAC light. Up to twelve, three-button keyfob transmitters can be used to activate the
receiver’s relay. The receiver has a terminal block for connecting the power and relay contacts. Each transmitter has a
unique address that is transmitted when a button is pressed. A “program” button is provided on the receiver to program
the transmitter(s) address into the receiver’s memory. An LED on the receiver indicates the receiver’s programming status
and illuminates when the receiver is energized. The receiver is encased in a waterproof enclosure. The operating range is
approximately 500 ft. Operating temperature range is 0°F to 160°F.
Polarity Reversing Output: The transmitter has two buttons assigned to the motor output. The up (^) button runs the
motor in one direction and the down (v) button runs the motor in the opposite direction. The reversing function
accomplished by reversing the phase on two of the four motor connections at the receiver output.
Manual Switch: The receiver is equipped with a manual switch. This switch replaces any hand or drum switch previously
connected to the motor.
Light Output: The light output is activated using the “B” button on the transmitter. Press button “B” once to latch this
output on. Press button “B” again to turn the light output off. The light function is active at all times and does not require
the power up sequence to be performed.
Maximum Ratings: Power for the receiver can be in the range of 100VAC to 132VAC. The relay contacts are rated at 20
Amps.
Page 1 REV B 05/20/19
(1) Long Range Antenna LRA340 **See PAGE 3 FOR SETUP**
- Rechargeable Transmitter GKF-WPTX-3L
- 3-Button Keyfob Transmitter KF340-3

Programming Instructions
Each transmitter has its own unique internal address along with the data as to which button is pressed and transmitted.
The receiver needs to be programmed to respond only to the specific transmitter it is intended to operate with. The
following steps configure the receiver to operate with a particular transmitter. Up to 12 transmitters can be programmed
to one receiver. Please read the entire programming procedure before starting. When the receiver enters program
mode, all previous transmitter addresses that were programmed will be erased from the receiver's memory.
1. Locate the pushbutton labeled "PROGRAM" on the receiver. Press and hold this button until the red LED next to the
program button illuminates (approximately 3 seconds). The receiver is now in the transmitter program mode. Release
the button. At this point all previously programmed transmitter addresses are erased from the receiver's memory.
2. To configure the receiver for a latching output, go to Step 4.
3. To configure the receiver for momentary output, press and release either button ONCE on the transmitter and verify that
the red program LED
extinguishes and then illuminates (blinks once). Proceed to Step 5.
4. To configure the receiver for latching output, press and release either button TWICE on the transmitter and verify that
the red program LED extinguishes and illuminates (blinks once).
5. Repeat previous step for additional transmitters that will operate with this particular receiver. The red LED on the
receiver will extinguish and illuminate (blink) once for the first transmitter being programmed, twice for the second, three
times for the third, etc. The receiver will not respond to transmitters that have already been programmed. The first
transmitter that is programmed determines the receiver’s relay operating mode.
6. The receiver will return to normal mode if no transmitter buttons are pressed for 5-seconds. The red LED on the
receiver will blink rapidly, then extinguish. The receiver is now in the normal mode of operation. This completes the
programming instructions. The receiver will retain all of its programming even when power is removed.
WWW.GAMAINC.COM
Page 2 REV B 05/20/19
LRF120VPR1L
Instruction Manual
T8 T5
T8 T5 LIGHT T2, T4 T1, T3 AC IN NEUT AC IN LINE
Long Range
Antenna Jack
Program
Switch
Program
LED

WWW.GAMAINC.COM
Page 3 REV B 05/20/19
Wiring Instructions
Prior to this, verify that there is no power at any of the motor terminals.
1. Disconnect or turn off the circuit breaker to remove power (if a hand or drum switch is connected to the motor it will
need to be disconnected). Takes notes before disconnecting the switch in the unlikely event it will need to be reconnected.
2. See motor connections using the tables on pages 4 and 5 for terminal connections specific to the motor.
3. 120VAC power is connected to the line and neutral terminal of the receiver.
NOTE: After completing the installation, if the motor goes the wrong direction, simply swap the wires connected to T5 and
T8 on the receiver. The motor will now rotate in the correct direction. The 120VAC light connects between “common” and
“light” terminals on the receiver.
LRF120VPR1L
Instruction Manual
T8
T5
LIGHT
T2, T4
T1, T3
AC IN NEUT
AC IN LINE

T8
T5
LIGHT
T2, T4
T1, T3
AC IN NEUT
AC IN LINE 120VAC IN
Relays shown in off position
Truth Table
K1 = Up or Down
K4 = Up
K2 = Light (Latch
On/Latch Off)
K4A
K4B
K1
K2
Schematic
LRF120VPR1L
Instruction Manual
Page 4 REV B 05/20/19

WWW.GAMAINC.COM
Page 5 REV B 05/20/19
Troubleshooting
All remote-control systems shipped by GAMA Electronics are 100% functionally tested just prior to shipment.
If your RF remote control system does not work out of the box, stops working or functions intermittently please take the
following steps to resolve common issues. Please note that you must be 2-3 feet away from the receiver when operating
the remote control. Operating within 2-3 feet may result in no operation or intermittent operation.
1. Replace the A23 12V Battery in the transmitter
· The remote control can activate during shipping and drain the battery that is installed in the control. We
send a replacement battery with the system if this occurs.
2. Check the voltage supply at the receiver
· The receiver is designed to function at 10-15VDC. Voltage on the (+) and (-) terminals on the control
should be within this range.
3. Reprogram the remote control
· If the system is non-functional try to reprogram the remote control. The program may not have taken
during the programming process or the program button may have been pressed. If the program button is
pressed the memory of the remote controls programed to the receiver are erased.
4. Listen and look for functionality on the receiver.
· The LED that is used for programming the system will illuminate when the receiver is activated. You will
also hear a “click” when the internal relays engage. If you can see the LED illuminate and you hear the
relay “click” the issue is most likely in the wiring or device being controlled.
5. Add a long-range antenna
· If the receiver is in an area that is averse to the reception of an RF signal, such as near a motor or in a
metal casing, a long-range antenna may solve the issue. Connect the antenna per the instructions on
page 3 and mount the antenna in an exposed area away from any motor.
LRF120VPR1L
Instruction Manual

Motor Name
A.O Smith with L1, L2 Terminals & Colored Wire
A.O. Smith C426 Motors with Terminals & Colored Wires
A.O. Smith C526 Motors with Terminals & Colored Wire
A.O. Smith C926 Motor with Colored Wire
A.O. Smith Motor 7-181021-20
A.O. Smith Motor C56A31B17
A.O. Smith Motor C56B05B17
A.O. Smith Motor
Ace Motors with Terminals
Baldor Motor CPI2000
Baldor Motor Type LC, DV
Baldor Motors with L1, L2 Terminals & Colored Wire
Century AC Motors with Colored Wire
Century AC Motors with Terminals & Colored Wire
Century Motors with Terminals
Dayton Motor 6K719L (Thermal Protection)
Eastbay Motors with Terminals
Elite Pointed Motors
Emerson Motors with Terminals
GE Motors with Terminals & Colored Wire
Leeson Motor M6K17F61A
Leeson Motors with Terminals
Leeson Type Motor (with Protector) M6C17FB10
Magnetek Motor 8-181021-20
Magnetek Motors with Terminals
Marathon Motor 5KC42JN0214 (3/4 HP)
Marathon Motor 5KC49PN0216 (1 HP)
Marathon Motor 5KC49TN0063Y
Marathon Motor 5KCP35KNB057AS
Marathon Motor 7PJ56C17F5945
Marathon Motors with Terminals & Colored Wire
Powerfist Motor 8703050
Regal Beloit Motor
Regal Beloit Motor 52A105379AA
Regal Beloit Motor C56AD36B17
Regal Beloit Motor with Type K Protector
WEG Motor with Protection
Figure
See Figure 3
See Figure 6
See Figure 6
See Figure 7
See Figure 19
See Figure 20
See Figure 20
See Figure 11
See Figure 8
See Figure 16
See Figure 17
See Figure 3
See Figure 7
See Figure 6
See Figure 4
See Figure 22
See Figure 5
See Figure 12
See Figure 10
See Figure 9
See Figure 21
See Figure 8
See Figure 18
See Figure 23
See Figure 4
See Figure 15
See Figure 15
See Figure 24
See Figure 24
See Figure 21
See Figure 9
See Figure 18
See Figure 11
See Figure 13
See Figure 14
See Figure 18
See Figure 25
STANDARD MOTOR WITH “T” NUMBERS
STANDARD MOTOR WITH COLORED WIRE
See Figure 1
See Figure 2
Page 6 REV B 05/20/19
WWW.GAMAINC.COM
LRF120VPR1L
Instruction Manual

FIGURE 1
FIGURE 3
FIGURE 2
FIGURE 4
T8
T5
T2,T4
T1,T3
T8
T5
T2,T4
T1,T3
T8
T5
T2,T4
T1,T3
RED
BLACK
L2
L1
T8
T5
T2,T4
T1,T3
RED
BLACK
WHITE/YELLOW
BLUE/ORANGE
T8
T5
T2,T4
T1,T3
TERMINAL 8
TERMINAL 5
TERMINAL 6
TERMINAL 1
*USE WIRE NUTS TO CONNECT
THE RECEIVER TO MOTOR WIRES
*USE WIRE NUTS TO CONNECT
THE RECEIVER TO MOTOR WIRES
Page 7 REV B 05/20/19
LRF120VPR1L
Instruction Manual

FIGURE 5
FIGURE 7
FIGURE 6
FIGURE 8
T8
T5
T2,T4
T1,T3
TERMINAL B
TERMINAL A
TERMINAL D
TERMINAL E
T8
T5
T2,T4
T1,T3
RED
YELLOW
BLUE
BLACK
T8
T5
T2,T4
T1,T3
Motor Red *Use blue wire nut
to connect the receiver to motor wire
TERMINAL 5
TERMINAL 6
TERMINAL 1
T8
T5
T2,T4
T1,T3
TERMINAL 3
TERMINAL 5
TERMINAL 2
TERMINAL 1
*MOTOR WIRES BROWN & ORANGE
MUST BE CONNECTED TO TERMINAL 3
Page 8 REV B 05/20/19
LRF120VPR1L
Instruction Manual

FIGURE 9
FIGURE 11
FIGURE 10
FIGURE 12
T8
T5
T2,T4
T1,T3
TERMINAL 2
MOTOR RED
MOTOR YELLOW
& WHITE
TERMINAL 1
T8
T5
T2,T4
T1,T3
RED
ORANGE
WHITE
BLACK
T8
T5
T2,T4
T1,T3
RED
BLACK
WHITE
ORANGE
*USE BLUE WIRE NUTS TO CONNECT THE
RECEIVER TO MOTOR WIRES
T8
T5
T2,T4
T1,T3
TERMINAL 4
TERMINAL 1
TERMINAL 3
TERMINAL 2
Page 9 REV B 05/20/19
LRF120VPR1L
Instruction Manual

FIGURE 13
FIGURE 15
FIGURE 14
FIGURE 16
T8
T5
T2,T4
T1,T3
RED
BLACK
2
1
T8
T5
T2,T4
T1,T3
RED
(2) BLACK
(1) ORANGE
WHITE
T8
T5
T2,T4
T1,T3
8
5
1
NO CONNECTION
T8
T5
T2,T4
T1,T3
BLACK
L1 (BLUE)
L2 (WHITE)
RED
*J-NEUTRAL IN RECEIVER
*4-NEUTRAL IN FROM AC POWER SOURCE
*LINE OF RECEIVER TO LINE OF
AC POWER SOURCE
Page 10 REV B 05/20/19
LRF120VPR1L
Instruction Manual

FIGURE 17
FIGURE 19
FIGURE 18
FIGURE 20
T8
T5
T2,T4
T1,T3
8 RED
5 BLACK
2 WHITE/4 YELLOW
1 BLUE/3 ORANGE
T8
T5
T2,T4
T1,T3
5
RED 2
YELLOW/WHITE
BLUE/ORANGE
T8
T5
T2,T4
T1,T3
RED
BLACK
L2
L1
T8
T5
T2,T4
T1,T3
T5
T2, T4
NO CONNECTION
T8
*P2, T3-NEUTRAL FROM AC INPUT
*P1-NEUTRAL FROM AC INPUT
*BLACK 4- NO CONNECTION
Page 11 REV B 05/20/19
LRF120VPR1L
Instruction Manual

FIGURE 21
FIGURE 23
FIGURE 22
FIGURE 24
T8
T5
T2,T4
T1,T3
RED
BLACK
YELLOW/WHITE
NO CONNECTION
T8
T5
T2,T4
T1,T3
(2) MOTOR RED
(5) MOTOR WHITE
(1) MOTOR BLACK
(ORANGE/BLUE)
(6) MOTOR ORANGE
(WHITE/YELLOW)
T8
T5
T2,T4
T1,T3
RED T8
BLACK T5
YELLOW T4,
WHITE T2
NO CONNECTION
T8
T5
T2,T4
T1,T3
T5
T2, T4
NO CONNECTION
T8
*P2, T3-NEUTRAL
*P1-NEUTRAL AC INPUT
*ORANGE/P2-NEUTRAL ON RECEIVER
*P1-NEUTRAL AC INPUT
*BROWN P2 ORANGE T3-NEUTRAL
*PURPLE P1-AC INPUT NEUTRAL
Page 12 REV B 05/20/19
LRF120VPR1L
Instruction Manual

FIGURE 25
T8
T5
T2,T4
T1,T3
RED (8)
BLACK (5)
BLUE (1)
ORANGE (3)
NO CONNECTION
*WHITE (2) BROWN (7/P2)-NEUTRAL
*YELLOW (4)-AC INPUT NEUTRAL
Page 13 REV B 05/20/19
LRF120VPR1L
Instruction Manual