KIPI ecoNET300 Series Specification sheet

OPERATION AND INSTALLATION MANUAL
ISSUE: 1.1_EN
APPLIES TO THE BOILER CONTROLLERS, SERIES: ecoMAX850, ecoMAX860, ecoMAX920
THE WEB MODULE
ecoNET300
REMOTE CONTROL OF BOILER CONTROLLERS
04-2020
www.econet24.com
ecoNET.apk
ecoNET.app

CONTENS OF TABLE
1. INFORMATION ABOUT DOCUMENTATION......... 4
2. APPLIED SYMBOLS .............................................. 4
4. DIRECTIVE WEEE 2012/19/UE..................................... 4
3. GENERAL INFORMATIONS .................................. 4
4. SAFETY INFORMATION........................................ 4
5. COOPERATION WITH CONTROLLERS .................. 5
6. CONNECTION TO THE CONTROLLER ................... 5
6.1 CONNECTION WITH ECOMAX850P2 ...................... 5
6.2 CONNECTION WITH ECOMAX860P3 ...................... 6
6.3 CONNECTION WITH ECOMAX920 .......................... 6
7. CONNECTION WITH INTERNET ........................... 6
8. LOGGING TO ECONET ACCOUNT ........................ 8
8.1 FIRST LOGGING TO ECONET ACCOUNT ..................... 8
9. WEBSITE SUPPORT.............................................. 9
9.1 CURRENT DATA.................................................... 9
9.2 DIAGRAM........................................................... 9
9.3 USER AND SERVICE PARAMETERS........................... 10
9.4 DATA HISTORY................................................... 10
9.5 ALARMS........................................................... 10
9.6 SCHEDULE ........................................................ 11
9.7 FUEL CONSUMPTION........................................... 11
9.8 DEVICE SETTINGS ............................................... 11
10. MOBILE APPLICATION....................................... 11
11. RESTORING DEFAULT USER NAME AND
PASSWORD ................................................................... 12
12. GNU GENERAL PUBLIC LICENSE NOTICE ........... 13

4
1. Information about documentation
The manual is a supplement for the
controller manual. In particular, except for
this manual, the controller manual should
also be observed. We are not responsible for
any damages caused by failure to observe
these instructions.
2. Applied symbols
In this manual the following graphic symbols
are used:
- the sign indicates that the
information provided relates to the
features of the module.
- the sign means that the posted
information has an impact on safety.
4. Directive WEEE 2012/19/UE
Purchased product is designed and made of
materials of highest quality. The product
meets the requirements of the Directive
2012/19/EU of 4 July 2012 on waste
electrical and electronic equipment
(WEEE), according to which it is marked by
the symbol of crossed-out wheeled bin (like
below), meaning that product is subjected to
separate collection.
Responsibilities after finishing a period of
using product:
•dispose of the packaging and product at
the end of their period of use in an
appropriate recycling facility,
•do not dispose of the product with other
unsorted waste,
•do not burn the product.
By adhering obligations of waste electrical
and electronic equipment controlled disposal
mentioned above, you avoid harmful effects
on the environment and human health.
3. General informations
The internet module enables controller
operation remote control (on-line) via
Internet. User can remotely monitor
operation of the controller and modify
operation parameters of the controller with
the use of a computer, tablet or mobile
phone. Essential features of the module:
•cooperation with www.econet24.com
external server provides access to
controller via Internet,
•supports Wi-Fi wireless networks,
•preview of current operation parameters
of the controller in readable and clear
“tiles”,
•visualization via readable hydraulic
diagram indicating current operation of
the hydraulic system,
•preview and edition options of most (user
and service) parameters of the controller,
•registration of operation parameters and
alarm conditions of the controller,
•possibility of e-mail notifications
concerning alarm conditions of the
controller.
4. Safety information
Device can be started and connected only by
a person who read this manual.
Connecting the internet module not in
accordance with the manual or improperly
can result in inappropriate operation of the
controller or interruption of its operation.
Verify if controller software is adapted to
cooperate with ecoNET300 internet module.
Do not use the device for other than
intended use.
Always turn off the controller before
connecting the internet module.

5
5. Cooperation with controllers
Check controller software version before
connecting a ecoNET300 module with the
controller.
In the controller main menu select tab:
MENU →Information →Software version
User can contact with the controller
manufacture in order to verify whether a
particular type of controller will be
cooperating with ecoNET300 according to
data concerning controller software versions.
6. Connection to the controller
The ecoNET300 internet module has to be
connected with controller with the use of
ecoLINK2 interface. In case of some types of
controllers it is necessary to use an
appropriate adapter. The ecoLINK2 interface
and adapter are a part of the ecoNET300 set.
Adapter: 1 - socket for RJ11 ecoLINK2 interface, 2
- a plug for controller module transmission socket,
3 - socket for a control panel plug.
6.1 Connection with ecoMAX850P2
The ecoMAX850P2 controllers are equipped
with just one COM transmission socket in
RJ11 standard which a control panel (located
inside or outside the controller housing) is
connected to. Using one RJ11 socket in the
module requires connecting an additional
divider (telephone RJ11 tee separator) and
additional cable.
Standard divider, RJ11 telephone divider: 1-
connection of RJ11 ecoLINK2 interface plug, 2-
connection of the control panel plug, 3-
connection of an additional cable with two RJ11
terminals.
Standard RJ11 telephone cable with an option of
connecting wires and a method of connecting into
the divider.
Below show location of the controller COM
transmission socket, where: interface
ecoLINK2,on diagram includes: COM
transmission socket (connection point
between cable and divider), divider, control
panel, additional room panel and additional
cable to a divider.
In order to connect the ecoNET300 module
with the controller, ecoLINK2 interface is
required which is a part of the set.
The internet module will cooperate only with
controllers with installed software supporting
ecoNET300 module.
In any circumstances do not modify
construction of the device.

6
6.2 Connection with ecoMAX860P3
In case of ecoMAX860P3 controller, a
El2adapter v2 must be used in order to
connect ecoLINK2 interface.
6.3 Connection with ecoMAX920
In case of ecoMAX920 controller, the
ecoLINK2 interface must be connected
directly to the controller's RJ11 socket.
7. Connection with Internet
Connect adapter plug to a mini USB Port
socket and 3G USB Port to the ecoLINK2
interface. Connect with RJ45 Ethernet Port
with Ethernet cable, e.g. with ADSL router,
switch and modem. A socket does not have
to be use in case of Wi-Fi wireless network
access. The Mode Switch can be set in any
position.
Connection of ecoNET300 with ETHERNET RJ45
with access points of LAN wire Internet network or
with Wi-Fi wireless network.
The ecoNET300 requires constant access to a
wire LAN or wireless Wi-Fi network in a place
of installation of the controller.
mini USB Port
3G USB Port
RJ45 Ethernet Port
Mode Switch

7
LED
LED
condition
Module operation
condition
Power
ON
Power on.
OFF
Power off.
Connection
with a
controller
ON
Active connection of the
controller.
OFF
No connection with
controller.
Connection
with WiFi
ON
Connection to a
programmed wireless
network is on.
OFF
No connection with
wireless network.
Connection
with a server
ON
Connection with
www.econet24.com
external server is on.
OFF
No connection for
www.econet24.com
external server.
After the power is on, ecoNET300 requires
app. 1 minute in order to load the
operational system. Then, the module begins
to work and indicates its condition with LED
indicators. In a connection between
ecoNET300 module with a controller is
active, a “ connection with controller”
indicator lights up. New functions for
managing ecoNET300 module are added to
the main menu.
MENU →Information →ecoNET WiFi
MENU →Information →ecoNET Ethernet
MENU →Main settings →WiFi
In case of connection with LAN wire network,
a ecoNET Ethernet tab will be available in
controller menu from which the IP number,
mask and gate can be read out and
ecoNET24 server connection condition can be
checked. It is required to save the displayed
IP number (e.g. IP:10.1.2.237). This
number in a form of: http://10.1.2.237 is
entered into the address field from the level
of LAN network. A website to operate the
controller menu will be activated.
It is necessary to enter network parameters
in General settings menu of the control
panel in order to make a wireless connection
via Wi-Fi.
To do this, select:
MENU →general settings →WiFi (WiFi
settings)
Select SSID in Network Settings. It is a
name of the local wireless network which has
to be the same for all devices working in this
network (SSID can be, e.g.: myWiFi).
In case of connection with a chosen Access
Point via wireless network, user has to know
the settings of Wi-Fi network which the
module will be connected to: network name
(SSID), protection type, access password.
The ecoNET300 requires active DHCP server
of Access Point (e.g. router) because
manual IP assignment for ecoNET300
internet module is not supported. More
information can be obtained from router
configuration software or network
administrator.
WPS/RESET button. Deleting user name
and password and restoring default
settings.
The LED indicators of module operation
condition.

8
Use the "TOUCH and PLAY" knob to select
letters and characters from the list, or touch
on the onscreen keyboard. Selected name is
confirmed with ENTER/OK.
In Network settings select Security.
Select and confirm encryption type in Wi-Fi
network (most often selected type is WPA2).
Go to Password tab. Enter Wi-Fi access
password using letters/characters available
on the listand confirm with ENTER/OK.
Filling data correctly results in ecoNET300
connected to a Wi-Fi network.
In the MENU →Information →ecoNET
WiFi, user can readout an IP number, Mask,
gate and ecoNET24 connection condition
(required: Server: Connected). IP number
is used for opening a boiler controller website
from a level of LAN network.
8. Logging to ecoNET account
The ecoNET300 internet module cooperates
with external server which is available under
www.econet24.com This provides access
to the controller via Internet.
In order to log into an account on an
external server, enter www.econet24.com
into an address field of the web browser.
Enter Login and Password in order to log
into ecoNET account.
To reminder the password for an existing
account, we choose FORGOT PASSWORD
and enter your email. A password reminder
will be sent to your email account.
8.1 First logging to ecoNET account
In case of first logging, user has to create a
new account in REGISTER tab.
Following conditions must be met:
•the controller has to be connected to a
power supply and properly connected to
internet module,
•the internet module should be connected
to the Internet and be logged into the
external server (“Server connection”
indicator is active),
•from ecoNET WiFi/Info tab in the
controller main menu, should be read the
UID number (unique ID of the
controller): MENU → Information →
ecoNET WiFi/Info
The UID number should be entered on the
REGISTRATION tab. If the system correctly
validates the UID number, the account
registration form will be displayed. It should
be complete the form with the data of the
controller user and enter the login password.
Form field:
•UID controller –the controller's UID is
shown. The ecoNET24 server verifies
whether UID number is correct.
•Controller label –enter any name of
controller.
The Wi-Fi network parameters (SSID,
protection type and password) can be also
configured from a level of ecoNET300
website after previously connecting it to a
LAN wire network.
myWiFi
B491JAKZ32C1I18800100
UID
Info

9
•Remote access to the controller by the
service and the producer –enables to
access and edit controller parameters via
the service and the producer.
•Controller installation address (Same as
the user's address) –check this field if
the controller address is the same as
residential address.
•Alarm notifications (Allows to send alarm
notifications by email) –in case an alert
occurs, an alarm message including
alarm contents will be sent on previously
entered e-mail address.
Obligatory fields: E-mail,Password,
Password (again).
Creating an ecoNET account will only be
possible after you have read the Terms of
Use in the form of regulations. Press the
Register button.
9. Website support
Description of the Web page menu for
managing the work of the controller.
Current data
Current readout of the controller
operation condition data and
possibility of changing its selected
parameters.
Diagram
Graphical representation of hydraulic
diagram of installation with current
operation condition readout for its
particular elements.
User
parameters
Detailed readout and modification of
operation parameters of the
controller.
Service
parameters
Detailed reading and modification of
advanced parameters of the
controller only after entering the
service password.
Data history
Data archive of selected controller
operation parameters.
Alarms
List of controller alarms.
Schedule
Work schedule of the controller and
temperature reduction.
Fuel
consumption
Graphical graph of fuel consumption.
NOTE: Tab available only in
controllers with dedicated software
by producer.
Device
settings
Information about controller and
additional modules, possibility to
change the address of controller
installation.
Devices
Option to read parameters from the
list of registered devices in one
ecoNET account.
My account
Logout
Add a new device UID to the list for
ecoNET account and logout.
Select a Web site language.
9.1 Current data
The Current Data tab includes tiles with
values of basic controller operation
parameters.
A parameter to be modified is indicated by
symbol. Just click on this tile and the
value change window will appear, where set
the new parameter value with the slider and
then confirm with the Save button.
Exit with modification without saving a new
setting is possible by clicking on the
symbol.
9.2 Diagram
The Diagram tab includes graphical
connection diagram between controller and
heating system in the building with readouts
of parameters from sensors in particular
points of the installation.
A parameter to be modified is indicated by
additional symbol.
User is required to know the operation of the
controller in order to modify its values.

10
Just click in the edit box and the value
change window will appear, where set the
new parameter value with the slider and
confirm with the Save button.
Exit with modification without saving a new
setting is possible by clicking on the
symbol.
9.3 User and service parameters
The basic parameters of the controller work
are displayed in the User parameters tab
and can be modified by the user. Advanced
parameters are displayed in the Service
parameters tab and can only be modified
after entering a service password.
All displayed parameters are grouped
accordingly.
Click on the name of the selected parameter
group and expand the list of available
parameters. Parameters to be modified is
indicated by symbol.
In order to change, select the appropriate
parameter name, click on the parameter, in
the additional window that appears, set the
new parameter value with the slider and
confirm with the Save button.
Exit with modification without saving a new
setting is possible by clicking on the
symbol.
9.4 Data history
The Data history tab enables to readout
registered parameters concerning operation
of the whole heating system in a selected
time and present it in the form of a graph.
Choose a time period for data readout by
clicking From: or To: (select date and time
in a calendar) or time interval: Last night,
last week, last month. The selection is
accepted by the Generate scheme button.
Then select from the list below the graph the
parameters that will be shown in this graph.
By specifying the choosing time zone in the
graph, you can rescaling this area on more
accurately.
In addition, clicking the symbol causes
the "nodes" to be displayed in the graph.
This is information about the time and value
of a single sample of data sent by the
controller to ecoNET24.
Return to the initial graph by pressing the
symbol.
The graph data can be saved as a *.CSV or
*.PNG file when you press symbol.
9.5 Alarms

11
In the Alarms tab, user can read:
•a list of registered alarms and other
events sent by the controller,
•a type of alarm, event and period of its
occurrence is displayed.
Log into www.econet24.com external
server in order to display all logs of alarm
conditions from the beginning of operation of
the controller.
Alarm notices can be sent on e-mail. It
enables the user to react fast in order to
restore normal operation of the controller.
9.6 Schedule
In the Schedule tab user have the option of
setting the time intervals, according to the
list after clicking on the symbol:
•reduction preset temperature of the
heating circuits.
Turn on the schedule by selecting On for the
available circulation from the list, and enter
the decreasing temperature value in the
Decrease field, .e.g. 10°C. On a bar chart
daily graph (24 hours), click on the
appropriate bars (each bar corresponds to 30
minutes), which allows to set the active
temperature reduction in the selected time
interval. Once set, choose Save.
Decreasing of preset temperature can be set
separately for all days of the week.
In the example above, on Tuesday, the
preset temperature for the heating circuit is
reduced by 10°C between 6:00 and 7:30 and
15:30 to 19:00. In other ranges, the preset
temperature will not be lowered.
9.7 Fuel consumption
In the Fuel consumption tab user can read
the fuel consumption in kilograms in a daily
cycle (every 1 hour) or a monthly cycle
(every 1 day).
9.8 Device settings
The Device settings tab enables to:
•change the controller installation address,
•reading basic Wi-Fi network parameters,
•readout a software version in the
controller module and additional modules
or panels,
•update internal ecoNET300 software.
The ecoNET24 server periodically checks
availability of new software version for the
ecoNET300 module. It displays information
concerning a new software version. All the
user needs to do is to press Update button.
When changing Wi-Fi network, click Refresh,
select Network name, and used Type of
security (e.g. WPA2 Personal) and enter
Password to a selected network.
All modifications must be confirmed by Save
button.
10.Mobile application
The mobile application allows remote access
via smartphone, tablet only to controllers
equipped with the ecoNET300 internet
module. The application uses an Internet
connection and a user account on the
www.econet24.com website.
The application allows to preview and
efficiently configure the most important
parameters of the controller. In this regard,
it primarily provides:
• preview basic operating parameters
The applications works only with ecoNET24
server, so should be need to sign up for an
ecoNET account to use them.
Software update process can be shorter or
longer depending on the speed of Internet
connection. Do not disconnect the device
from a power supply during update process
because it will cause its damage.

12
• possibility to modify values of selected
parameters
• view and edit time schedules
• reading the alarm list.
The ecoNET.apk for Android application is
available for free download directly under the
link:
ecoNET.apk
ecoNET.app
11.Restoring default user name and
password
Default username and password (user:
admin, password: admin) can be restored
with the use of WPS/RESET button located
near indicators on the ecoNET300 housing.
The ecoNET300 module has to be connected
to power supply.
1. Push WPS/RESET button during normal
module operation.
2. Hold this button pressed for at least 10
seconds.
3. Release the WPS/RESET button.
4. A LED indicator near the button should
flash several times.
5. Wait for app. 2 minutes.
6. The module will automatically start up
and connect with the Internet.
7. Default username and password will be
restored (user: admin, password:
admin).
Register of changes:
v1.1 –04-2020 –added point 12.
In case the user has forgotten his password
for logging in the Internet module, it is
possible to restore default data with the use
of a button on the ecoNET300 housing.

13
12.GNU General Public License Notice
This product includes software code developed by third parties,including
software code subject to the GNU General Public License ("GPL"). As
applicable, PLUM sp. z o.o. provides mail service of a machine readable
copy of the corresponding GPL source code on CD-ROM upon request
via email ([email protected]) or traditional paper mail (PLUM sp. z o.o., ul.
Wspólna 19, Ignatki, 16-001 Kleosin, Polska) will charge for a nominal
cost to cover shipping and media charges as allowed under the GPL. This
offer will be valid for at least 3 years.
The GPL Code used in this product is distributed WITHOUT ANY
WARRANTY and is subject to the copyrights of one or more authors.
Please refer to the following GNU General Public License for further
information.
GNU GENERAL PUBLIC LICENSE
Version 2, June 1991
Copyright (C) 1989, 1991 Free Software Foundation, Inc.
51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA
Everyone is permitted to copy and distribute verbatim copies
of this license document, but changing it is not allowed.
Preamble
The licenses for most software are designed to take away your freedom to
share and change it. By contrast, the GNU General Public License is
intended to guarantee your freedom to share and change free software--to
make sure the software is free for all its users. This General Public
License applies to most of the Free Software Foundation's software and to
any other program whose authors commit to using it. (Some other Free
Software Foundation software is covered by the GNU Lesser General
Public License instead.) You can apply it to your programs, too.
When we speak of free software, we are referring to freedom, not price.
Our General Public Licenses are designed to make sure that you have the
freedom to distribute copies of free software (and charge for this service if
you wish), that you receive source code or can get it if you want it, that
you can change the software or use pieces of it in new free programs; and
that you know you can do these things.
To protect your rights, we need to make restrictions that forbid anyone to
deny you these rights or to ask you to surrender the rights. These
restrictions translate to certain responsibilities for you if you distribute
copies of the software, or if you modify it.
For example, if you distribute copies of such a program, whether gratis or
for a fee, you must give the recipients all the rights that you have. You
must make sure that they, too, receive or can get the source code. And
you must show them these terms so they know their rights.
We protect your rights with two steps: (1) copyright the software, and (2)
offer you this license which gives you legal permission to copy, distribute
and/or modify the software.
Also, for each author's protection and ours, we want to make certain that
everyone understands that there is no warranty for this free software. If
the software is modified by someone else and passed on, we want its
recipients to know that what they have is not the original, so that any
problems introduced by others will not reflect on the original authors'
reputations.
Finally, any free program is threatened constantly by software patents.
We wish to avoid the danger that redistributors of a free program will
individually obtain patent licenses, in effect making the program
proprietary. To prevent this, we have made it clear that any patent must
be licensed for everyone's free use or not licensed at all.
The precise terms and conditions for copying, distribution and modification
follow.
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND
MODIFICATION
0. This License applies to any program or other work which contains a
notice placed by the copyright holder saying it may be distributed under
the terms of this General Public License. The "Program", below, refers to
any such program or work, and a "work based on the Program" means
either the Program or any derivative work under copyright law: that is to
say, a work containing the Program or a portion of it, either verbatim or
with modifications and/or translated into another language. (Hereinafter,
translation is included without limitation in the term "modification".) Each
licensee is addressed as "you".
Activities other than copying, distribution and modification are not covered
by this License; they are outside its scope. The act of running the
Program is not restricted, and the output from the Program is covered only
if its contents constitute a work based on the Program (independent of
having been made by running the Program). Whether that is true depends
on what the Program does.
1. You may copy and distribute verbatim copies of the Program's source
code as you receive it, in any medium, provided that you conspicuously
and appropriately publish on each copy an appropriate copyright notice
and disclaimer of warranty; keep intact all the notices that refer to this
License and to the absence of any warranty; and give any other recipients
of the Program a copy of this License along with the Program.
You may charge a fee for the physical act of transferring a copy, and you
may at your option offer warranty protection in exchange for a fee.
2. You may modify your copy or copies of the Program or any portion of it,
thus forming a work based on the Program, and copy and distribute such
modifications or work under the terms of Section 1 above, provided that
you also meet all of these conditions:
a) You must cause the modified files to carry prominent notices stating
that you changed the files and the date of any change.
b) You must cause any work that you distribute or publish, that in whole
or in part contains or is derived from the Program or any part thereof, to
be licensed as a whole at no charge to all third parties under the terms of
this License.
c) If the modified program normally reads commands interactively when
run, you must cause it, when started running for such interactive use in
the most ordinary way, to print or display an announcement including an
appropriate copyright notice and a notice that there is no warranty (or
else, saying that you provide a warranty) and that users may redistribute
the program under these conditions, and telling the user how to view a
copy of this License. (Exception: if the Program itself is interactive but
does not normally print such an announcement, your work based on the
Program is not required to print an announcement.)
These requirements apply to the modified work as a whole. If identifiable
sections of that work are not derived from the Program, and can be
reasonably considered independent and separate works in themselves,
then this License, and its terms, do not apply to those sections when you
distribute them as separate works. But when you distribute the same
sections as part of a whole which is a work based on the Program, the
distribution of the whole must be on the terms of this License, whose
permissions for other licensees extend to the entire whole, and thus to
each and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest your rights
to work written entirely by you; rather, the intent is to exercise the right to
control the distribution of derivative or collective works based on the
Program.
In addition, mere aggregation of another work not based on the Program
with the Program (or with a work based on the Program) on a volume of a
storage or distribution medium does not bring the other work under the
scope of this License.
3. You may copy and distribute the Program (or a work based on it, under
Section 2) in object code or executable form under the terms of Sections 1
and 2 above provided that you also do one of the following:
a) Accompany it with the complete corresponding machine-readable
source code, which must be distributed under the terms of Sections 1 and
2 above on a medium customarily used for software interchange; or,
b) Accompany it with a written offer, valid for at least three years, to
give any third party, for a charge no more than your cost of physically
performing source distribution, a complete machine-readable copy of the
corresponding source code, to be distributed under the terms of Sections
1 and 2 above on a medium customarily used for software interchange;
or,
c) Accompany it with the information you received as to the offer to
distribute corresponding source code. (This alternative is allowed only for
noncommercial distribution and only if you received the program in object
code or executable form with such an offer, in accord with Subsection b
above.)
The source code for a work means the preferred form of the work for
making modifications to it. For an executable work, complete source code
means all the source code for all modules it contains, plus any associated
interface definition files, plus the scripts used to control compilation and
installation of the executable. However, as a special exception, the source
code distributed need not include anything that is normally distributed (in
either source or binary form) with the major components (compiler, kernel,
and so on) of the operating system on which the executable runs, unless
that component itself accompanies the executable.
If distribution of executable or object code is made by offering access to
copy from a designated place, then offering equivalent access to copy the
source code from the same place counts as distribution of the source
code, even though third parties are not compelled to copy the source
along with the object code.
4. You may not copy, modify, sublicense, or distribute the Program except
as expressly provided under this License. Any attempt otherwise to copy,
modify, sublicense or distribute the Program is void, and will automatically
terminate your rights under this License. However, parties who have
received copies, or rights, from you under this License will not have their
licenses terminated so long as such parties remain in full compliance.

14
5. You are not required to accept this License, since you have not signed
it. However, nothing else grants you permission to modify or distribute the
Program or its derivative works. These actions are prohibited by law if you
do not accept this License. Therefore, by modifying or distributing the
Program (or any work based on the Program), you indicate your
acceptance of this License to do so, and all its terms and conditions for
copying, distributing or modifying the Program or works based on it.
6. Each time you redistribute the Program (or any work based on the
Program), the recipient automatically receives a license from the original
licensor to copy, distribute or modify the Program subject to these terms
and conditions. You may not impose any further restrictions on the
recipients' exercise of the rights granted herein. You are not responsible
for enforcing compliance by third parties to this License.
7. If, as a consequence of a court judgment or allegation of patent
infringement or for any other reason (not limited to patent issues),
conditions are imposed on you (whether by court order, agreement or
otherwise) that contradict the conditions of this License, they do not
excuse you from the conditions of this License. If you cannot distribute so
as to satisfy simultaneously your obligations under this License and any
other pertinent obligations, then as a consequence you may not distribute
the Program at all. For example, if a patent license would not permit
royalty-free redistribution of the Program by all those who receive copies
directly or indirectly through you, then the only way you could satisfy both
it and this License would be to refrain entirely from distribution of the
Program.
If any portion of this section is held invalid or unenforceable under any
particular circumstance, the balance of the section is intended to apply
and the section as a whole is intended to apply in other circumstances.
It is not the purpose of this section to induce you to infringe any patents or
other property right claims or to contest validity of any such claims; this
section has the sole purpose of protecting the integrity of the free software
distribution system, which is implemented by public license practices.
Many people have made generous contributions to the wide range of
software distributed through that system in reliance on consistent
application of that system; it is up to the author/donor to decide if he or
she is willing to distribute software through any other system and a
licensee cannot impose that choice.
This section is intended to make thoroughly clear what is believed to be a
consequence of the rest of this License.
8. If the distribution and/or use of the Program is restricted in certain
countries either by patents or by copyrighted interfaces, the original
copyright holder who places the Program under this License may add an
explicit geographical distribution limitation excluding those countries, so
that distribution is permitted only in or among countries not thus excluded.
In such case, this License incorporates the limitation as if written in the
body of this License.
9. The Free Software Foundation may publish revised and/or new
versions of the General Public License from time to time. Such new
versions will be similar in spirit to the present version, but may differ in
detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Program
specifies a version number of this License which applies to it and "any
later version", you have the option of following the terms and conditions
either of that version or of any later version published by the Free
Software Foundation. If the Program does not specify a version number of
this License, you may choose any version ever published by the Free
Software Foundation.
10. If you wish to incorporate parts of the Program into other free
programs whose distribution conditions are different, write to the author to
ask for permission. For software which is copyrighted by the Free
Software Foundation, write to the Free Software Foundation; we
sometimes make exceptions for this. Our decision will be guided by the
two goals of preserving the free status of all derivatives of our free
software and of promoting the sharing and reuse of software generally.
NO WARRANTY
11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE,
THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT
PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE
STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER
PARTIES PROVIDE THE PROGRAM "AS IS" WITHOUT WARRANTY
OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF
THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE
DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY
SERVICING, REPAIR OR CORRECTION.
12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR
AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY
OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE
PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR
DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR
INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED
TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR
LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF
THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN
IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
How to Apply These Terms to Your New Programs
If you develop a new program, and you want it to be of the greatest
possible use to the public, the best way to achieve this is to make it free
software which everyone can redistribute and change under these terms.
To do so, attach the following notices to the program. It is safest to attach
them to the start of each source file to most effectively convey the
exclusion of warranty; and each file should have at least the "copyright"
line and a pointer to where the full notice is found.
one line to give the program's name and an idea of what it does.
Copyright (C) yyyy name of author
This program is free software; you can redistribute it and/or
modify it under the terms of the GNU General Public License
as published by the Free Software Foundation; either version 2
of the License, or (at your option) any later version.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See
the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program; if not, write to the Free Software
Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301,
USA.
Also add information on how to contact you by electronic and paper mail.
If the program is interactive, make it output a short notice like this when it
starts in an interactive mode:
Gnomovision version 69, Copyright (C) year name of author
Gnomovision comes with ABSOLUTELY NO WARRANTY; for details
type `show w'. This is free software, and you are welcome
to redistribute it under certain conditions; type `show c'
for details.
The hypothetical commands `show w' and `show c' should show the
appropriate parts of the General Public License. Of course, the
commands you use may be called something other than `show w' and
`show c'; they could even be mouse-clicks or menu items--whatever suits
your program.
You should also get your employer (if you work as a programmer) or your
school, if any, to sign a "copyright disclaimer" for the program, if
necessary. Here is a sample; alter the names:
Yoyodyne, Inc., hereby disclaims all copyright
interest in the program `Gnomovision'
(which makes passes at compilers) written
by James Hacker.
signature of Ty Coon, 1 April 1989
Ty Coon, President of Vice
This General Public License does not permit incorporating your program
into proprietary programs. If your program is a subroutine library, you may
consider it more useful to permit linking proprietary applications with the
library. If this is what you want to do, use the GNU Lesser General Public
License instead of this License.

15

ul. Obornicka 71
62-002 Suchy Las, Poland
Phone: [phone]
[e-mail]
www.kipi.pl
National Waste Database No. 000179569