GardenJoy FH-GT120 User manual

Demonstration of Installation Procedures of Mower
The package contains the following components:
（1）A charger
（2）A mower shield and a strip of anti-collision wire
（3）Spare blade, a blade base, a wrench, a blade
locknut
（4）Work head of mower
（5）Middle connecting rod of mower
（6）One set of mower auxiliary handle, four fixed
screws/nuts, one hexagon wrench
（7）Starting handle of mower, one battery
（8）Manual
（9）A goggles
1）Connect the charger to the top charging hole of
battery, see Figure ①;
2）The red indicator of charger is on, meaning
charging, see Figure ②;
3）The green indicator is on, meaning charging
completed, see Figure ③;
I. Charge the battery and open the package of
accessories （1）: A charger
13
2
3
1
4
5
6
7
8
910
11
2
3

1）The installation direction of shield is close to the
human during the operation process;see figure ①;
2）Align the four-angle buckle of the shield at the
cutter head slot of the mower, press down to the
end and then rotate until it aligns at the four-angle
buckle of cutter head, see Figure ②;
3）Install the anti-collision wire, push the sides of the
wire into the holes on both sides of the cutter
head. The bottom of the wire contacts the ground
in the correct installation method, see Figure ③;
Notes: If no wire is installed, the blade may be
damaged when operating the mower;
Demonstration of wrong installation
1）Remove the nuts of mower cutter head, see
Figure ①;
2）The blade base is installed reversely, see
Figure ②;
3）The blade locknut is installed reversely, see
Figure ③;
IV. Install the middle connecting rod of mower
and open the package of accessories (5): Middle
connecting rod of mower
1）Align the opposite-side nut slot of base to the
mower motor or the nut on the screw shaft. The
nuts of cutter head should remain in the original
position, see Figure ①;
2）Install the blade in the base front blade slot. After
the successful installation, the cutter head screw
should expose 1/3 inches, see Figure ②;
3）Install the blade locknut. Note that the nuts with
pattern are downward (the wrong installation will
make the cutter head fall down), see Figure ③;
4）Tighten the blade locknut clockwise with a
wrench, see Figure ④.
III. Install the blade base and blade, and open the
package of accessories (3)(4): Spare blade, a
blade base, a wrench, a blade locknut, work head
of mower
1）Align at the arrow marks on both ends of connect-
ing rod and insert it, see Figure ① .
2）Align the plug at one end of the connecting rod
with the slot at the other end, see Figure②.
3）Referring to the rivets on the connecting rod, the
upper and lower rivet holes are inserted in a
straight line inserted, see Figure③.
4）Tighten the lock sleeve of rod in the locking
direction, see Figure ④.
II. Install the mower shield and anti-collision
wire, and open the package of accessories
（2）: A mower shield and a strip of anti-colli-
sion wire
2
1
X
13
2
13
2
2
3 4
Demonstration of wrong installation of mower
shield:
1）The shield is mounted in the opposite direction of
the handle;
2）The bottom of the anti-collision wire is installed
reversely without contact with the ground;
XX X
4
1

VI. Install the battery and open the package of
accessories (7): Starting handle of mower, one
battery
VII. Installation completed
V. Install the auxiliary handle of mower and open
the package of accessories (6); One set of mower
auxiliary handle, four fixed screws/nuts, one
hexagon wrench
1）Hold the clips on both sides of the battery, see
Figure ①;
2）Align the battery slot buckle and push hard in.
The sound means successful installation, see
Figure ②;
3）Remove the battery, hold the buckle on both
sides of the battery, pull it out of the slot and pull
out the battery.
VIII. Startup test
1）The starting handle includes the red round
self-lock knob and the red long-shaped start
trigger, and the red round self-lock knob is the
fuse button;.
2）The mower starts when pressing the fuse button
before pulling the trigger, see Figure ①;
3）After startup, release the round fuse button. Press
the red long-shaped start trigger to maintain
working; release the trigger to stop working, see
Figure ②;
4）Repeat these steps 2) 3) to continue working.
1）Adjust the installation position by itself according
to the height;
2）Open the rubber shock absorption sleeve of
handle, see Figure ①;
3）Install the lower base of auxiliary handle, and pull
the upper and lower bases on the rubber shock
absorption cover to make the screw holes
aligned, see Figure ②;
4）Place the screws in the four holes and hold the
upper and lower bases, see Figure ③;
5）Tighten screws with a hexagon wrench (prevent
from screwing off), see Figure ④;
12
3 4
12
12
5
2
1
4
3

Telephone: [phone]
Email: shenzhenniumai@ 163. com
URL: www.5startool.com
Fecebook: https://www.facebook.com/kevein.jo
Youtube:https://www.youtube.com/channel/UCQzsxnaeX7QDTOwassFyfQg