Garmin Edge 810 Instruction manual

November
2012
Edge
®
810
Quick
Start
Manual
Sj)eed
18.2'::
a
stance
20
.
23
'l'
aevatlon
Totl
.
Ascent
1087
{
1155
{
cadence
190-0151
0-01
_
08
Printed
in
Taiwan

Introduction
&WARNING
See
the
Important
Safety
and
Product
Information
guide
in
the
product
box
for
product
warnings
and
other
important
information.
Always
consult
your
physician
before
you
begin
or
modify
any
exercise
program.
Getting
Started
When
using
your
device
the
first
time
,
you
should
complete
these
tasks
to
set
up
the
device
and
learn
about
the
basic
features.
1
Install
your
device
using
the
standard
mount
(page
3)
or
the
out-front
mount
(page
4).
2
Turn
on
the
device
(page
4).
3
Locate
satellites
(page
6).
4
Go
for
a
ride
(page
7)
.
5
Charge
the
device
(page
2).
6
Register
the
device
(page
14)
.
7
Upload
your
ride
to
Garmin
Connect™
(page
7).
8
Get
the
owner's
manual
(page
15).
Charging
the
Device
NOTICE
To
prevent
corrosion
,
thoroughly
dry
the
mini-USB
port
,
the
weather
cap
,
and
the
surrounding
area
before
charging
or
connecting
to
a
computer.
The
device
is
powered
by
a
built-in
li
thium-ion
battery
that
you
can
charge
using
a
standard
wall
outlet
or
a
USB
port
on
your
computer.
NOTE:
The
device
will
not
charge
when
outside
the
temperature
range
of
32
°
to
113°F
(0°
to
45°C).
1
Pull
up
the
weather
cap
CD
from
the
mini-USB
port
@.
-------------
2

2 Plug the small end of the USB cable
into the mini-USB port.
3 Plug the USB end of the cable into the
AC adapter or a computer USB port .
4 Plug the AC adapter into a standard
wall outlet.
When you connect the device to a
power source , the device turns on .
5 Charge the device completely.
A fully charged battery can run for up to
15 hours before it must be recharged .
Installing the Standard Mount
For the best GPS reception, position the
bike mount so the front of the Edge is
oriented toward the sky . You can install
the bike mount on the stem or the
handlebars.
1 Select a secure location to mount the
Edge where it does not interfere with
the safe operation of your bike .
2 Place the rubber disk CD on the back
of the bike mount.
The rubber tabs align with the back of
the bike mount so it stays in place.
3 Place the bike mount on the bi ke
stem .
4 Attach the bike mount securely using
the two bands (l).
5 Align the tabs on the back of the Edge
with the bike mount notches @.
6 Press down slightly and turn the Edge
clockwise until it locks into place.
3

Installing the Out-Front Mount
1 Select a secure location to mount the
Edge where it does not interfere with
the safe operation of your bike .
2 Use the hex key to remove the screw
CD from the handlebar connector <2) .
3 If you want to change the orientation
of the mount, remove the two screws
on the back side of the mount @,
rotate the connector @, and replace
the screws.
4 If the handlebar diameter is 26 mm,
place the rubber pad around the
handlebar.
5 Place the handlebar connector around
the rubber pad or handlebar (31.8 mm
diameter).
6 Replace the screw.
4
NOTE: Garmin® recommends a
torque specification of 7 lbf-in . (0.8 N-
m). Check the tightness of the screw
periodically .
7 Align the tabs on the back of the Edge
with the bike mount notches @.
8 Press down slightly and turn the Edge
clockwise until it locks into place.
Releasing the Edge
1 Turn the Edge clockwise to unlock the
device .
2 Lift the Edge off the mount.
Turning On the Device
The first time you turn on the device, you
are prompted to configure system settings
and profiles (page 13) .
1 Hold 6.

2 Follow the on-screen instructions .
3 If your device included a heart rate
monitor and a GSC™ 10 , activate the
ANT +™ sensors during configuration .
For more information about ANT+
sensors , see page 10.
Keys
CD
6
Select to turn the backlight on and
off.
Hold to turn the device on and off.
@ 0
Select to mark a new lap.
®
1_...
Select to start and stop the timer .
Home Screen Overview
The home screen gives you quick access
to all the features of the Edge.
~ Bike1
Select to change your bike
>
profile .
RIDE Select to go for a ride.
Road )
Select to change your activity
profile .
•
Select to manage your history ,
courses , workouts , and
personal records .
~~ J
Select to view the map.
*
Select to view the setup menu.
Using the Touchscreen
• When the timer is running , tap the
screen to view the timer overlay.
The ti mer overlay allows you to use
the settings and search features
during a ride.
• Select ../ to save your changes and
close the page .
•
Select X to close the page and return
to the previous page.
• Select ~ to return to the previous
page.
5

• Select ...... to return to the home
screen.
• Select ~ and + to scroll.
• Select (C•)) to view the connections
page.
• Select o. to search for a location .
•
Select ® to search near a location.
• Select 1!!1 to search by name .
•
Select 3 to delete an item.
Viewing the Connections Page
The connections page displays the status
of the satellite signals, ANT+ sensors , and
your smartphone.
6
From the home screen , select the
status bar at the top of the page.
/!NT+ Sen~ors
Phone Connect1ons
The connections page appears .A
flashing icon means the device is
searching . You can select any icon to
change the settings.
Acquiring Satellite Signals
Before you can use the GPS tracking and
navigation features , you must acquire
satellite signals.
The device may need a clear view of the
sky to acquire satellite signals . The time
and date are set automatically based on
the GPS posit i on.
1 Go outdoors to an open area.

The
front
of
the
device
should
be
oriented
toward
the
sky.
2
From
the
home
screen,
select
RIDE.
3
Wait
while
the
device
locates
satellites.
It
may
take
30-60
seconds
to
locate
satellite
signals.
TIP:
Do
not
begin
moving
until
the
timer
page
appears
(page
7).
Going
for a
Ride
Before
you
can
record
speed
and
distance,
you
must
locate
satellite
signals
(page
6)
or
pair
your
device
with
an
optional
ANT+
sensor.
NOTE:
History
is
recorded
only
while
the
timer
is
running.
1
From
the
home
screen,
select
RIDE.
2
Wait
while
the
device
locates
satellites.
3
Select
I~
to
start
the
timer.
11me
01:08:43
Speed
18.2~
IJstance
20.23T
Bevation
Totl.
Ascent
10871 11551
cadence
Heart
Rate
83~
163!
4
Swipe
the
screen
for
additional
data
pages.
5
If
necessary,
tap
the
screen
to
view
the
timer
overlay.
6
Select
I~
to
stop
the
timer.
7
Select
Save.
Sending
Your
Ride
to
Garmin
Connect
NOTICE
To
prevent
corrosion,
thoroughly
dry
the
mini-USB
port,
the
weather
cap,
and
the
surrounding
area
before
charging
or
connecting
to
a
computer.
7

1
Pull
up
the
weather
cap
CD
from
the
mini-USB
port
(2)
.
2
Plug
the
small
end
of
the
USB
cable
into
the
mini-USB
port.
3
Plug
the
large
end
of
the
USB
cable
into
a
computer
USB
port.
4
Go
to
www.garminconnect.com.
5
Select
Getting
Started
.
6
Follow
the
on-screen
instructions.
Garmin
Connect
Garmin
Connect
gives
you
a
simple
way
to
store
and
track
your
activities,
analyze
your
data,
and
share
with
others.
To
sign
up
for
a
free
account,
go
to
www
.garminconnect.com.
Store
your
activities
:
After
you
complete
and
save
an
activity
with
your
device,
8
you
can
upload
that
activity
to
Garmin
Connect
and
keep
it
as
long
as
you
want.
Analyze
your
data:
You
can
view
more
detailed
information
about
your
activity
,
including
an
overhead
map
view,
pace
and
speed
charts
,
and
customizable
reports
.
Share
your
activities:
You
can
email
your
activities
to
others
,
or
post
links
to
your
activities
on
your
favorite
social
networking
sites
.
Connected
Features
The
Edge
has
several
connected
features
for
your
compatible
Bluetooth®-enabled
smartphone.
For
more
information
about
how
to
use
your
Edge
,
go
to
www
.
garmin.com/intosports/apps
.

NOTE:
Your
Edge
must
be
connected
to
your
Bluetooth-enabled
smartphone
to
take
advantage
of
these
features.
Live
Track:
Allows
friends
and
family
to
follow
your
races
and
training
activities
in
real
time.
You
can
invite
followers
using
email
or
social
media,
allowing
them
to
view
your
live
data
on
a
Garmin
Connect
tracking
page.
Activity
upload
toGarmin
Connect:
Automatically
sends
your
activity
to
Garmin
Connect
as
soon
as
you
finish
recording
the
activity.
Course
and
workout
downloads
fromGarmin
Connect:
Allows
you
to
search
for
activities
on
Garmin
Connect
using
your
smartphone
and
send
them
to
your
device
so
that
you
can
repeat
them
as
a
course
or
workout.
Social
media
interactions:
Allows
you
to
automatically
post
an
update
to
your
favorite
social
media
website
when
you
upload
an
activity
to
Garmin
Connect.
Weather
updates:
Sends
real-time
weather
conditions
and
alerts
to
your
device.
Following
a
Course
From
the
Web
Before
you
can
download
a
course
from
Garmin
Connect,
you
must
have
a
Garmin
Connect
account
(page
8).
1
Connect
the
device
to
your
computer.
2
Go
to
www.garminconnect.com.
3
Create
a
new
course
or
select
an
existing
course.
4
Select
Send
to
Device.
5
Disconnect
the
device,
and
turn
it
on.
6
Select
II
>
Courses.
7
Select
the
course.
8
Select
RIDE.
Locations
You
can
record
and
store
locations
in
the
device.
Saving
Your
Location
You
can
save
your
present
location,
such
as
your
home
or
parking
spot.
9

From
the
home
screen,
select
*-
>
System
>
GPS
>
Mark
Location
>
~.
History
History
includes
time,
distance,
calories,
speed,
lap
data,
elevation,
and
optional
ANT+
sensor
information.
NOTE:
History
is
not
recorded
while
the
timer
is
stopped
or
paused.
When
the
device
memory
is
full,
a
message
appears.
The
device
does
not
automatically
delete
or
overwrite
your
history.
Upload
your
history
to
Garmin
Connect
periodically
to
keep
track
of
all
your
ride
data.
Viewing
Your
Ride
1
From
the
home
screen,
select
II
>
Rides.
2
Select
Last
Ride
or
All
Rides.
3
Select
an
option.
Deleting
History
1
From
the
home
screen,
select
II
>
Delete.
2
Select
an
option:
10
•
Select
All
Rides
to
delete
all
saved
activities
from
the
history.
•
Select
Old
Rides
to
delete
activities
recorded
more
than
one
month
ago.
•
Select
All
Totals
to
reset
all
distance
and
time
totals.
NOTE:
This
does
not
delete
any
saved
activities.
•
Select
All
Courses
to
delete
all
courses
you
have
saved
or
transferred
to
the
device.
•
Select
All
Workouts
to
delete
all
workouts
you
have
saved
or
transferred
to
the
device.
•
Select
All
Personal
Records
to
delete
all
personal
records
saved
to
the
device.
NOTE:
This
does
not
delete
any
saved
activities.
3
Select~.
ANT+
Sensors
Your
device
can
be
used
with
wireless
ANT+
sensors.
For
more
information
about
compatibility
and
purchasing