Garmin StreetPilot I2 - Automotive GPS Receiver Setup guide

➋
Set Up the i2/i3
Press and hold the Power button to
turn on the i2/i3. Follow the instructions
on the screen to set up the i2/i3. Roll
the Wheel up and down to highlight
options. Press in to select options.
➌
Install Software and Load Maps
Do not connect your i2/i3 to your computer until you are told to do so!
1. Insert the Setup DVD-ROM into your computer’s DVD-ROM
drive.
If the welcome screen does not automatically appear, click
Start and then Run on your personal computer. Type the
letter of your DVD-ROM drive followed by setup.exe (example:
D:\setup.exe). Then press Enter.
2. Follow the instructions on the screen to install software and
load maps to your i2/i3.
3. When MapInstall opens, click the map to select the regions you
want to load to your i2/i3. Selected maps are shaded pink.
Find a Place and Go!
Select Start Navigating.
➎
Select a destination.
➍
Enjoy the route!
➏
Select a category.
➌
Select Food, Hotels,
and More.
➋
Select Where To?
➊
Tip: To narrow your search, select the <Spell> field and enter letters in the name of
the place.
➍
Mount the i2/i3
1. Place the suction cup mount on your windshield with the lever
pulled toward you, as shown above.
2. Press the lever toward the windshield.
3. Plug one end of the vehicle adapter into the USB port on the
i2/i3. Plug the other end into a receptacle in your vehicle.
Windshield USB port
Lever
PowerWheel
Getting Started
➊
Insert Batteries
1. Press down on the tab and pull to remove the battery door.
2. Insert two AA batteries.
3. Press down on the battery door as you slide it back into place.
Tab
Setup
DVD-ROM
Unlock sheet
USB cable
Vehicle adapter cable
i2/i3 and mount
WARNING: For use in vehicles, it is the sole responsibility of the owner/operator of a vehicle with the i2/i3 installed
to place and secure the device so it will not interfere with the vehicle operating controls and safety devices, obstruct the
driver’s view of driving conditions, or cause personal injury in the event of an accident.
NOTICE TO STATE OF CALIFORNIA DRIVERS: California Vehicle Code Section 26708 (a) (1) provides that
drivers in California should not use suction mounts on their windshield or side or rear windows. Other Garmin dashboard
or friction mounting options should be used. For available accessories, refer to the Garmin Web site at www.garmin.com.
Also, refer to the Owner’s Manual for instructions on using the included mounting disk with the suction cup mount.
Keep batteries installed in your i2/i3 so it can find satellites quickly.
NOTE: Keep your Unlock sheet in a safe place for future reference.

StreetPilot® i2/i3
Set up and go!
Following Your Route
Follow the route to your destination using the map. The position icon shows
your current location.
Your position
Distance to the
next turn
Time you will arrive at
your destination
Press to return to
main page Roll to zoom in
and out
Text directions
A checkered flag marks
your destination.
Follow the arrows as
you take turns.
Your route is marked
with a red line.
Finding an Address
Select Where To? > Address to begin.
➍
If necessary, select
a city.
Select the correct
address.
➎
Select Start
Navigating.
➏
Enter the street name.
Press and select
the correct street from
the list.
➌
Enter the house number.
Then press .
➋
Select a state.
➊
Setting a Home Location
You can set a Home location for the place you return to most often. Then,
select Where To? > Go Home to go Home.
From the main page,
select Where To? > Go
Home.
➊
Press the Wheel to
acknowledge the
message.
➌
Select an option.
➋
Adjusting Volume and Screen Brightness
From the main page, select Settings. Then select Set Volume or Set
Brightness. Roll the Wheel up or down to change the setting.
More Information
For more information about your i2/i3, refer to the Owner’s Manual located
on the Setup DVD-ROM. You can also view it online at http://www.garmin.
com/products/spi3 or spi2. Click the Manuals link and then select Download.
July 2005 190-00613-01 Rev. B Printed in Taiwan
StreetPilot i3 shown