Gateway Solo 1400 Parts list manual

www.gateway.com
Replacing the Solo 1400/1450
Keyboard
This package includes a replacement keyboard for your Solo 1400 or Solo 1450
notebook and these printed instructions.
Tools you need
You need a small Phillips and flat blade screwdriver to replace the keyboard.
Preventing static electricity discharge
The components inside your computer are extremely sensitive to static
electricity, also known as electrostatic discharge (ESD).
Before replacing the keyboard, follow these guidelines:
■Turn off the computer power.
■Wear a grounding wrist strap (available at most electronics stores) and
attach it to a bare metal part of the computer.
■Touch a bare metal surface on the back of the computer.
■Unplug the power cord and modem and network cables.
■Remove the battery.
Caution ESD can permanently damage electrostatic
discharge-sensitive components in the computer. Prevent
ESD damage by following ESD guidelines every time you
open the computer case.
Warning To avoid exposure to dangerous electrical voltages and
moving parts, turn off your computer and unplug the power
cord and modem and network cables before opening the
case.
Warning To prevent risk of electric shock, do not insert any object
into the vent holes of the notebook.

2www.gateway.com
Before working with computer components, follow these guidelines:
■Avoid static-causing surfaces such as carpeted floors, plastic, and packing
foam.
■Remove components from their antistatic bags only when you are ready
to use them. Do not lay components on the outside of antistatic bags
because only the inside of the bags provide electrostatic protection.
Removing the keyboard
To remove the keyboard:
1Follow the guidelines under “Preventing static electricity discharge” on
page 1.
2Shut down your notebook.
3Unplug the AC adapter and modem and network cables.
4Remove the battery.
5Open the LCD panel to the normal viewing position.
Warning To avoid injury, disconnect the AC adapter and modem and
network cables before removing the keyboard. Replace the
keyboard before reconnecting power.

3
Replacing the Solo 1400/1450 Keyboard
www.gateway.com
6Insert a small flat blade screwdriver under the bottom-right corner of the
keyboard bezel, between the INS and DEL keys, and gently pry it up.
Important Inserting a piece of cloth between the screwdriver and
keyboard and notebook case will help prevent damage to
your notebook.

4www.gateway.com
7Pull the bezel off the notebook. You will hear small snapping sounds as
the bezel comes off of the notebook. Be careful not to break off the tabs
located on the left end of the bezel.
8With a small Phillips screwdriver, remove the two keyboard screws and
put them in a safe place.

5
Replacing the Solo 1400/1450 Keyboard
www.gateway.com
9Raise the back edge of the keyboard slightly, then carefully slide the
keyboard back until the five tabs on the front edge of the keyboard are
free from their slots.
10 Slowly rotate the keyboard toward you so it lies keys-down on top of
the notebook. Be careful not to damage the LCD panel.

6www.gateway.com
11 Pull up on the plastic keyboard connector using two fingers. After the
connector is in the raised position, gently pull the cable out of the
connector. Be careful not to touch or damage any other components.

7
Replacing the Solo 1400/1450 Keyboard
www.gateway.com
Installing the keyboard
To install the new keyboard:
1Place the new keyboard keys-down on the notebook with the space bar
away from you.
2Pull up on the keyboard connector, located near the middle of the system
board, to verify the connector is in the raised position.
3Slide the end of the keyboard cable into the keyboard connector.
4Press down on the keyboard connector using two fingers. This locks the
keyboard cable into the keyboard connector.
5Rotate the keyboard toward the LCD panel until the keyboard is almost
face-up.
Important The keyboard cable should slide easily into the keyboard
connector. The cable is correctly oriented if it is not twisted.

8www.gateway.com
6Insert the five tabs located on the front edge of the keyboard into the
corresponding slots under the palm rest.
7Gently press the keyboard down until it is flat all the way across. The
keyboard should easily fall into place. Be careful not to damage the LCD
panel.

9
Replacing the Solo 1400/1450 Keyboard
www.gateway.com
8Replace the two keyboard screws.
9Slide the two tabs located on the left end of the bezel under the notebook
frame.

10 www.gateway.com
10 Press down on the bezel in several places until it clicks in place.
The bezel is correctly mounted when you can run you finger along the
bezel and find no loose spots. The bezel should be flat all the way across.
If the bezel is mounted incorrectly, complete the instructions under
“Replacing the bezel” on page 11.
11 Replace the battery.
12 Plug in the AC adapter and modem and network cables.
13 Turn on the notebook.
Warning If the bezel is not correctly replaced, your notebook could
be damaged when you try to close the LCD panel.